GRAUPNER mz-24 Pro Programming Manual page 84

Deleting Saved Trimming Positions
Press to highlight the field with the trimming value to
be deleted. In the example below, T3 needs to be
reset:
BACK
PHASE 1 Trim Step
SE T1 T2 T3 T4
02 04 04
STEP 04
POS 000% +13% 000% –07%
SET 000% 000% –006% 000%
D.TRIM 1 NONE AUTO TRIM INH
D.TRIM 2 NONE CTL ON
Press the RES button to reset the highlighted field
back to the default value. In the example below, T3
has been reset to 000%:
BACK PHASE 1 Trim Step
SE T1 T2 T3 T4
STEP 04 02 04 04
+13% 000%
POS 000% –07%
SET 000% 000% 000% 000%
D.TRIM 1 NONE AUTO TRIM BLK
D.TRIM 2 NONE CTL ON
Use the same procedure for other trimming values.
Digital Trim 1 and 2
Independent of the trim control 1 - 4 settings de-
scribed above, the INC/DEC buttons DT1 and DT2
on the transmitter (near switches S2 and S3) can be
assigned to control channels 5 - 12 via the D.TRIM
1 and D.TRIM 2 lines of this display. Depending on
the CO (common) or SE (single) setting at the top
left side of the display, follow the storage of their trim
options accordingly CO (common) or SE (single).
The possible trim amount is ±30 %.
84 Base menu - Trim setting
Programming
Press the button in the line of the desired control. In
the example below, D.TRIM 1 needs to be reassigned:
BACK
SERVO
VIEW
STEP
INC
POS
RES
SET
DEC
D.TRIM 1
SET
D.TRIM 2
The field highlights blue:
BACK
STEP
SERVO
POS
VIEW
SET
INC
D.TRIM 1
RES
D.TRIM 2
DEC
Press the INC
SET
the display to increase/decrease the channels CH5 -
CH12. Alternatively, press the arrow keys ( pq ) to
the left of the display screen to achieve the same re-
sult. Press the
ue back to the default
D.TRIM 1 needs to be reassigned to Channel 8:
BACK
STEP
POS
SET
D.TRIM 1
D.TRIM 2
Use the same procedure for D.TRIM 2.
PHASE 1 Trim Step SERVO
SE T1 T2 T3 T4 VIEW
INC
04 02 04 04
000% +13% –06% –07% RES
Press
000% 000% 000% 000% DEC
NONE AUTO TRIM INH SET
NONE CTL ON
PHASE 1 Trim Step SERVO
SE T1 T2 T3 T4 VIEW
INC
04 02 04 04
000% +13% –06% –07% RES
000% 000% 000% 000% DEC
NONE AUTO TRIM INH SET
NONE CTL ON
or DEC button at the right edge of
RES button to reset the changed val-
NONE
. In the example below,
PHASE 1 Trim Step SERVO
SE T1 T2 T3 T4 VIEW
INC
04 02 04 04
000% +13% –06% –07% RES
000% 000% 000% 000% DEC
CH8 AUTO TRIM INH SET
NONE CTL ON
Tip
Refer to the Programming Examples section (page
230) for trim setting examples.
Press the VIEW button on the top right of the display
to view and verify setting changes. All trim controls
are graphically displayed, as shown below:
BACK
PHASE 1
000% 000%
000% 000%
000%
000 000 000
000
The graphic display represents individual trim control-
lers according to the following schematic:
BACK PHASE 1
DV1 000% 000% DV4
SL2
000% 000%
DT1 DT2
TRIM
000%
DV2 DV3
000 000 000
000
TRIM
Tip
The main menu shortcut for this display can be reached
by pressing on the top central yellow bar graphics:
000%
TX RX
RX 05.5V
000:00.0
000 000
Press
mz
000:00.0
0:01:23
M - 1
000 000
PHASE 1
MODEL NAME 1
BATT TIME 00: 01: 23
000
STEP
000%
000
000
STEP
SL1
000%
000
000
000%
4.2V
000