GRAUPNER mz-24 Pro Programming Manual page 195

Notice
The available setting options depend on the
number of ailerons selected during the basic set-
tings of the model (BASE submenu Model Type).
To save and exit, press the BACK
left of the display to return to the previous menu:
BACK
THERMIK FLAP MIX
FLAP TYP ACT SET CTL
Press
>>
FLAP
AILE >> FLAP ON >> ON
>>
ELEV >> FLAP INH ON
INH >> ON
FLAP >> ELEV
ELEV >> FLAP line
To support the elevator in tight curves and aerobatics,
the flap function can be included by controlling the
elevator with this mixer. Select the mixing direction
so that the flaps move downward when the elevator is
pulled (up), and conversely upward when the elevator
is pushed (down).
A symmetrical or an asymmetrical effect can be de-
fined for each flap pair. Values of ±125% are possible.
The aileron uniform default values are +30%:
BACK
SPEED Flap MIX
ELEV >> FLAP CTL ON
AILE1 AILE3 AILE4 AILE2
RATE A +030% +030% +030% +030%
+030%
RATE B +030% +030% +030%
The flaps uniform default values are +30%:
ELEV >> FLAP
button at the top
RATE A
RATE B
SERVO
Adapt the individual values as described in the FLAP
Line section (page 192).
Notice
The available setting options depend on the
number of ailerons selected during the basic set-
tings of the model (BASE submenu Model Type).
To save and exit, press the
left of the display to return to the previous menu:
Press
SERVO
FLAP >> ELEV line
NEXT
When setting flaps, upward or downward torque can
INC
arise about the transverse axis. Elevated flaps also
RES cause the models to fly faster. These reactions can
DEC
be achieved with the mixer.
When setting the flaps, use this mixer to have the ai-
leron position automatically track the flaps depending
on the set value.
BACK SERVO
SPEED Flap MIX
CTL ON
NEXT
FLAP1 FLAP2 INC
FLAP3 FLAP4
+030% +030% +030% +030% RES
DEC
+030% +030% +030% +030%
BACK
button at the top
BACK SPEED Flap MIX SERVO
FLAP TYPE ACT SET CTL
>>
FLAP
>>
AILE >> FLAP ON ON
RUDD >> FLAP ON >> ON
>>
FLAP >> ELEV INH ON
The setting can be symmetrical or asymmetrical to the
flap control center point.
The adjustment range is ±125%. This mixers normal
settings lie within the single-digit to low double-digit
range. By default, 0% is uniformly set:
BACK
SPEED Flap MIX
FLAP >> ELEV CTL
ELEV1
RATE A 000%
RATE B 000%
Adapt the individual values as described in the FLAP
Line section (page 192).
BACK
To save and exit, press the
left of the display to return to the previous menu:
BACK SPEED Flap MIX
FLAP TYPE ACT SET
Press
>>
FLAP
>>
AILE >> FLAP ON
ELEV >> FLAP ON >>
>>
FLAP >> ELEV ON
BACK
Press the button at the top left of the display
to return to the FUNCTION menu:
BACK BASE FUNCTION
Phase D/R,EXPO THR.CRV Idle LOW
Snap roll Aile diff Wing MIX Flap MIX
Airbrake TTrainer Logical sw Sequence
Function menu | Airplane models - Flaps mixer
SERVO
ON
INC
RES
DEC
button at the top
SERVO
CTL
ON
ON
ON
SYSTEM
Prog.MIX
Flap set
V-Tail
195