GRAUPNER mz-24 Pro Programming Manual page 106

BACK Telemetry
RECV
RX FAIL SAFE V6.35<>
>OUTPUT CH : 01
GAM
INPUT CH : 01
EAM
MODE : HOLD
F.S.POS : 1234µsec
VARIO
DELAY : 0.25sec
FAIL SAFE ALL : NO GPS
POSITION : 1234µsec
ESC
Turn off the transmitter and verify the fail safe posi-
tions by checking the servo travel.
Fail Safe in Combination With Channel Mapping
Make sure that mapped servos (controlled by com-
mon control channels) react in the same way during
a malfunction. Use the corresponding settings of the
INPUT CH to manage the mapped servo behavior.
In the example below, receiver servo connections 06,
07 and 08 are mapped by assigning the same control
channel 04 as the INPUT CH to OUTPUT CH (receiver
servo connections):
BACK Telemetry
RX FAIL SAFE V6.35 < > RECV
>OUTPUT CH : 06
GAM
INPUT CH : 04
MODE : HOLD EAM
F.S.POS : 1500µsec
VARIO
DELAY : 0.25sec
FAIL SAFE ALL : NO
GPS
POSITION : 1500µsec
ESC
BACK Telemetry
RX FAIL SAFE V6.35 < >
RECV
>OUTPUT CH : 07
GAM
INPUT CH : 04
MODE : HOLD
EAM
F.S.POS : 1500µsec
VARIO
DELAY : 0.25sec
FAIL SAFE ALL : NO
GPS
POSITION : 1500µsec
ESC
106 Base menu - Telemetry | SETTINGS/DISPLAYS
BACK
ESC
RX FAIL SAFE
>OUTPUT CH :
DEC
INPUT CH
INC
MODE
F.S.POS
ENT
DELAY
SET
FAIL SAFE ALL : NO
POSITION
The INPUT CH 04 determines the fail safe behavior
of these three servos connected to control channel
4 fully independent of the settings of the respective
OUTPUT CH:
BACK
RX FAIL SAFE
OUTPUT CH : 04
INPUT CH
>MODE
F.S.POS
DELAY
FAIL SAFE ALL : NO
POSITION
This is also true when INPUT CH 01 is used for map-
ping:
ESC
BACK
DEC
RX FAIL SAFE
OUTPUT CH : 04
INC
>INPUT CH
ENT
MODE
F.S.POS
SET
DELAY
FAIL SAFE ALL : NO
POSITION
In this case, servo connection 04 reacts according to
ESC
the fail safe settings of CH 01.
DEC
The reaction time or delay set in the DELAY line con-
INC
trastingly applies uniformly to all channels set to mode
ENT
FAI-SAFE (fail safe).
SET
Telemetry
V6.35 < > RECV
ESC
08
GAM DEC
: 04
: HOLD INC
EAM
: 1500µsec
VARIO ENT
: 0.25sec
GPS SET
: 1500µsec
ESC
Telemetry
V6.35 < > RECV ESC
DEC
GAM
: 04
: FAI-SAFE EAM INC
: 1500µsec
VARIO ENT
: 0.25sec
GPS
SET
: 1500µsec
ESC
Telemetry
V6.35 < > RECV ESC
DEC
GAM
: 01
: FAI-SAFE INC
EAM
: 1500µsec
VARIO ENT
: 0.25sec
GPS SET
: 1500µsec
ESC
RX FREE MIXER
BACK
Telemetry
RX FREE MIXER V6.35 < >
RECV
>MIXER : 1
GAM
MASTER CH : 00
SLAVE CH : 00
EAM
S-TRAVEL– : 100
VARIO
S-TRAVEL+ : 100
RX WING MIXER
GPS
TAIL TYPE : NORMAL
ESC
Value Explanation
V#.## Receiver firmware
version
MIXER
Mixer selection
MASTER Signal source or
CH
source channel
SLAVE CH Target channel
S-TRAVEL– Mixing (in percent-
age of servo travel)
the -minus side of
the servo travel
S-TRAVEL+ Mixing (in percent-
age of servo travel)
the +plus side of
the servo travel
RX WING Tail type
MIXER
TAIL TYPE
MIXER
Up to five mixers can be programmed in the MIXER-
line by selecting one of mixers 1 to 5.
The settings programmed in this display only relate to
the mixers selected in the MIXER line.
ESC
DEC
INC
ENT
SET
Settings
None
1 to 5
0, 1 + depending
on the receiver
0, 1 + depending
on the receiver
0% to 100 %
0% to 100 %
NORMAL,
V-TAIL (V-LW)
ELEVON
(elevator/aileron
mixer for delta
and flying wing)