Table of Contents
Advertisement
Control Set
In depending on the selected model type, more or fewer mixing
and other functions are activated in a newly created model mem-
ory, but are assigned and can be also operated on the model, only
stick functions ST1 ... ST4, see figure on the left. This is not a mis-
take, but is due to the model pilot's choice and the individual
model equipment. Additional control elements must be assigned
as required and according to individual preferences. Shown as an
example in the „Control Set" menu of the basic menu.
Control assignment step-by-step
1. Open desired submenu.
Here is an example of the „Control Set" submenu of the „green"
basic menu.
2. In the desired line, touch the --- symbol in the „Control" column.
Here as an example in the line of the control function „5". The
display shown on the left will appear.
3. Now press the desired control element, for example the left
slider on the middle board. The selection menu shown on the
left opens:
– In the left-hand column, the position of the control is indi-
cated visually and the designation of the control is given
below, here „SL1".
– In the second column from the left, the current encoder posi-
tion is visualized optically and numerically.
– Tapping the box labeled „Reverse" reverses the direction of
action. Visually recognizable in the right column.
– After an encoder assignment, the symbol
mode of action of the selected control is displayed in the
„Type" column. In the example, the symbol for a propor-
tional control or three-stage switch with an effective range
from -100% to 0% to +100%.
By tapping on the symbol, you can choose between further
types of effects in the rotation process:
... as before, but with a one-sided effective range of 0%
... 100%.
... like a jog or digital switch with a preset increment of
4%, which can be adjusted accordingly in the „Switch Set"
menu.
... acts as an ON/OFF switch.
– In the right column, the result is visualized as a function of
the path.
– Tapping „OK" completes the process.
– Tapping „back" cancels the process.
40 / 64
Set transmitter and mixer characteristics
for the typical
33040_mc32exHoTT_V1.00_en
33040_mc32exHoTT_V1.00_en
Delete a Control
Tapping on the Control designation in the „Ctrl" column opens its
configuration menu. Tapping on „delete" deletes the control
assignment.
Note
Further information can be found in the help text that appears
after tapping the question mark at the top right.
Both the control characteristics in the "Control Set" submenu of
the "green" basic menu and the mixer characteristics of the vari-
ous functions in the "orange" menu are essentially set according
to the same principles. The corresponding procedure is shown
below using the gas curve. However, the settings shown are purely
for demonstrative purposes and in no way correspond to real gas
characteristics!
Select characteristic step-by-step
1. Open desired submenu.
Here is an example of the "Control Set" submenu.
2. In the desired line, tap the symbol
in the „Detail" column.
Here is an example of the „Throttle" control function. The display
shown on the left will appear.
3. Touch the „Curve" field at the bottom of the screen. Select the
desired characteristic curve using rotation method, whereby the
following information on the „desired characteristic curve" refers
to the blue characteristic curve in the left display and not to the
representation in the symbol.
You can choose from:
– A linear characteristic with no points between the two end
points.
This characteristic corresponds to the standard setting.
– A linear characteristic with 5 points evenly distributed
between the end points.
This characteristic is to be selected as the basis for nonlinear
characteristics.
– A flat curve with a single point in the center of the control.
The horizontal characteristic can only be shifted vertically
and can therefore be used, f. e. as basis for speed specifica-
tions for speed controllers.
4. If needed, at the bottom right, in the field under „smoothed",
select whether the characteristic should be „angular" or
„rounded".
41 / 64
Advertisement
Table of Contents
