Error Code Details - Canon iR3570 Service Manual

Chapter 15

15.2 Error Code Details

15.2.1 Error Code Details
iR2270 / iR2870 / iR3570 / iR4570 / / iR2270N / / iR2870N / / iR3570N / / iR4570N / iR2230 / /
E000
E001
E002
E003
E007
E010
E014
15-2
Code Error name/description
communication error for pedestal/ communication error for 3-way unit-
E716
A1
E717 communication error for NE controller
E719 coin vendor error
E730 PDL software error
E732 scanner communication error
E733 printer communication error
E740 Ether board error
E743 DDI communication error
E744 language file/boot ROM error
E745 TokenRing board error
E746 accessories board wrong model error
E748 controller board and SDRAM size mismatch
E805 fan error
Code Cause
The temperature of the fixing assembly is abnormally high.
0001 While startup control is under way, the reading of
the main thermistor is less than 30 deg C
continuously for 200 msec or more 1 sec after the
start of power supply.
While startup control is under way, the reading of
the main thermistor is less than 70 deg C
continuously for 200 msec or more 2 sec after the
start of power supply.
While startup control is under way, the reading of
the main thermistor is less than 120 deg C
continuously for 200 msec 6 sec after the start of
power supply.
The startup control does not end 30 sec after the
start of power supply.
The temperature of the fixing assembly is abnormally high.
0000 The reading of the main thermistor is 250 deg C
or more continuously for 200 msec.
0001 The hardware circuit detects overheating of the
main or sub thermistor for 200 msec.
0002 The reading of the sub thermistor is 295 deg C or
more continuously for 200 msec.
The rise in temperature of the fixing assembly is faulty.
0000 While startup control is under way, the reading of
the main thermistor is less than 115 deg C
continuously for 400 msec 1.3 sec after it has
indicated 100 deg C.
While startup control is under way, the reading of
the main thermistor is less than 150 deg C
continuously for 400 msec 1.3 sec after it has
indicated 140 deg C.
The fixing temperature is too low after a standby state.
0000 While regular temperature control is under way,
the reading of the main thermistor is less than 140
deg C continuously for 400 msec or more.
The rotation of the fixing film is faulty.
0000 While the fixing motor is rotating, the marker
signal is not detected for 6 sec with the reading of
the main thermistor indicating 100 deg C or more.
The rotation of the main motor is faulty.
0001 Detection is executed every 100 msec after the
start of motor rotation; however, the drive
detection signal is absent for 2 sec.
0002 During motor rotation, detection is executed
every 100 msec; however, the drive signal is
absent 5 times in sequence.
The rotation of the fixing motor is faulty.
0001 Detection is executed every 100 msec after the
start of motor rotation; however, the drive
detection signal is absent for 2 sec.
T-15-2
Remedy
Reset the condition in service mode:
COPIER>FUNCTION>CLEAR>ERR. Replace the
main thermistor. Replace the DC controller PCB.
Reset the condition in service mode:
COPIER>FUNCTION>CLEAR>ERR. Replace the
main thermistor. Replace the DC controller PCB.
Reset the condition in service mode:
COPIER>FUNCTION>CLEAR>ERR. Replace the
DC controller PCB.
Reset the condition in service mode:
COPIER>FUNCTION>CLEAR>ERR. Replace the
sub thermistor. Replace the DC controller PCB.
Reset the condition in service mode:
COPIER>FUNCTION>CLEAR>ERR. Replace the
main thermistor. Replace the DC controller PCB.
Reset the condition in service mode:
COPIER>FUNCTION>CLEAR>ERR. Replace the
main thermistor. Replace the DC controller PCB.
Reset the condition in service mode:
COPIER>FUNCTION>CLEAR>ERR. Replace the
main thermistor. Replace the DC controller PCB.
Replace the main motor. Replace the DC controller
PCB.
Replace the main motor. Replace the DC controller
PCB.
Replace the fixing motor. Replace the DC controller
PCB.
0008-1078