Copier; Test (Test Print Mode) - Canon iR3570 Service Manual

FONTDL
MENU-1 to
MENU-4

16.7 TEST (Test Print Mode)

16.7.1 COPIER

16.7.1.1 Copier List
iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 /
<PG>
TYPE
TXPH
PG-PICK
2-SIDE
PG-QTY
<NETWORK>
PING
1) Press the switch at the operating section long for the shutdown sequence and turn the main power switch OFF.
2) Connect the network cable to this machine and turn the main power switch ON.
3) Notify the system administrator that the machine has been installed to request network setup.
4) Notify the system administrator of the network connection check plan and check the PING remote host address (IP address of a PC terminal in the user network).
5) Select the service mode (COPIER>TEST>NETWORK>PING), enter the IP address checked at Step 4 from the ten-key pad of the operating section, and press
the OK key and the Start key.
- Once the network has been connected normally, OK is displayed. (End)
- If NG is displayed, check the connection of the network cable first. If the network cable is connected normally, do Step 6 and later. If the network cable is not
connected normally, repeat Step 5.
6) Select the service mode (COPIER>TEST>NETWORK>PING), enter the loopback address *(127.0.0.1), and press the OK key and the Start key.
- If NG is displayed, the TCP/IP setting of the local machine may be wrong. Return to Step 3 and check the setting again.
- If OK is displayed, the TCP/IP setting of the local machine seems correct but the network controller (main controller circuit board) may be faulty. Check the
controller at Step 7.
*: Since the loopback address signal is returned before the network controller, the TCP/IP setting of the local machine can be checked.
7) Select the service mode (COPIER>TEST>NETWORK>PING), enter the local host address (IP address of the local machine), and press the OK key.
- If NG is displayed, the IP address of the local machine may be wrong or the network controller may be faulty. Check the IP address with the system
administrator or replace the main controller circuit board.
Sub-item
Setting whether or not to display the font service setting screen for list
display by the PS kanji font downloader
<Setting value>
0: Do not display [Default]
1: Display
Setting whether or not to display Levels 1 to 4 of the printer setting menu
<Setting value>
0: Do not display
1: Display
[Value at shipping/Value after RAM clearance: 0]
Sub-item
Enter a test print type number and press the Start key for test printing. (After test
printing, be sure to return the number to 0.)
0: Image from CCD (Ordinary print)
1: Checker
2: 17 tones (Error diffusion method [T0BIC])
3: 17 tones (Dither screen method)
4: Totally white 00H
5: Halftone 80H (Error diffusion method [T0BIC])
6: Halftone 80H (Dither screen method)
7: Totally black FFH
8: Horizontal line (space: 27 dots, line width: 40 dots)
9: Horizontal line (space: 50 dots, line width: 60 dots)
10: Horizontal line (space: 3 dots, line width: 2 dots)
11: Halftone 60H (Error diffusion method [T0BIC])
12: Halftone 60H (Dither screen method)
13: Halftone 30H (Error diffusion method [T0BIC])
14: Halftone 30H (Dither screen method)
15 - 20: For development
Reserved
Selecting an output stage for test printing
1: Cassette 1
2: Cassette 2
3: Cassette 3
4: Cassette 4
5: Side deck
6: Manual feed
7 - 8: Not used
Setting the output mode for test printing
0: Simplex [Default] 1: Duplex
Setting the number of pages for test printing
1 to 999 [Default: 1]
Sub-item
Checking the connection from this machine to the network (TCP/IP only)
The network connection is checked when the machine has been installed and when the
connection has become faulty.
T-16-61
BOARD > OPTION
Description
T-16-62
COPIER>TEST>PG
Description
T-16-63
COPIER>TEST>NETWORK
Description
Chapter 16
Level
1
2
Level
1
1
1
1
1
Level
1
0008-0571
16-49