Error Code (Send); Results Of Self-Diagnosis - Canon iR3570 Service Manual

Chapter 15
Code
0004 An attempt to switchover to a language on the HDD fails.
1000 The boot ROM that is mounted is of the wrong type.
2000 The engine ID indicated by the software ID is illegal.
E745 There is a fault on the TokeRing board.
0001 An attempt at PCI initialization has failed.
0002 The MAC address is faulty.
0003 There is an error in the acquisition/setting of board information.
0004 There is a connection error.
0005 Other Errors
E746 The accessories board is of the wrong type.
0003 At startup, a board for a different model has been detected.
E748 There is a mismatch between controller board and SDRAM size.
1001 There is a mismatch between the control board and the SDRAM.
E805 There is a fan error.
0000 While the fan is at rest, the lock signal has been detected for 5 sec.
While the fan is in operation, the lock signal is not detected for 5 sec.

15.3 Error Code (SEND)

15.3.1 Results of Self-Diagnosis

iR2270 / iR2870 / iR3570 / iR4570 / / iR2270N / / iR2870N / / iR3570N / / iR4570N / iR2230 / / iR3530 /
Cause
There is a shortage of TCP/IP resources. Try again later.
While continuous transmission is under way or has
ended in FTP or Windows (SMB), a shortage of TCP/IP
resources has occurred, not permitting reference.
Set the IP address.
The IP address of the machine has yet to be set.
The server does not respond. Check the settings.
The settings of the selected server are not correct, or the
server has not been turned on. Or, there may be a
shortage of resources.
NetWare is in use. Try again later.
NetWare is printing using PSeve or NDSPServer, not
permitting browsing.
The layer in question at the target is too deep to browse.
The number of characters is in excess of the number
allowed.
There is no response.
The server is not ready for file transmission.
The network is cut for file transmission. (An attempt to
connect to the target of transmission may have failed, or
there is an open circuit in the middle.)
The tree name is not specified for NetWare
transmission.
An error has occurred for TCP/IP in the course of e-mail
or i-fax transmission.
Check TCP/IP.
The machine's TCP/IP is not in operation.
The selected server cannot be found. Check the settings.
The IP address in question cannot be identified.
If the login information for the LDAP server is set to
'use (security authentication)', the host name in question
cannot be identified.
The selected server cannot be connected. Check the settings.
15-16
Cause
T-15-8
Remedy
Wait a while; then, try again.
In user mode, set the IP address; thereafter, turn off and
then on the machine.
Wait a while; then, try again. If browsing is still not
permitted, select a different server.
Wait until NetWare finishes printing; then, try again.
The layer in question cannot be specified. Specify a
different address.
Check the target.
Check the network.
Type in the tree name.
Check the condition of the network cable and the
connector.
In user mode, check the TCP/IP settings (IP address,
DHCP, RARP, BOOTP).
1. In user mode, check the DNS settings.
2. On the DNS side, check the DNS data settings.
In user mode, check the TCP/IP settings (DNS settings).
Remedy
Download a language file of the correct version.
Replace the boot ROM with one of the model in question.
Replace it with a software ID of the correct model.
1. Disconnect and then connect the TokeRing board.
2. Replace the TokeRing board.
1. Replace the TokenRing board.
1. Replace the TokenRing board.
1. Check the connection of the cable.
2. Replace the cable.
3. Check the power source of the MAU.
4. Replace the MAU.
5. Replace the TokenRing board.
Replace the UFR board of the correct type (model).
Check the correct combination between board and SDRAM.
Replace the fan. Replace the DC controller PCB.
0008-0278