Canon iR3570 Service Manual page 673

AP-CODE
<COMBO>
Sub-item
PPR-SLCT
MOD-SLCT
ENV-SLCT
TR-SW1/2/3/4/5
<LCNS-TR>
Example of display: ST-XXXX 1 ( ) {0 to 0}
[1] [2]
[1] Status display 0: Not installed [Default] 1: Installed
[2] Invalidation 0: Invalidate (Only 0 can be entered.)
Transfer invalidation procedure
1. Select ST-XXXX, enter 0, and press the OK key.
2. A transfer license number (24 digits) is displayed at TR-XXXX.
ST-SEND
TR-SEND
COPIER > OPTION > INT-FACE
Sub-item
Setting a CPCA path for a print job from the PrintMe application installed in the PS
print server unit
<Setting range>
0 to 99999999 [Default: 0]
SW for the setting of transfer lead edge weak bias (paper type)
<Setting range>
1: Plain paper (Default), 2: Thick paper, 3: Envelope, 4: Intermediate paper, 5: OHP, 6: Postcard, 7: Label
paper, 8: Bond paper
<Additional information>
The transfer lead edge weak bias becomes effective with the following settings.
1.Output condition: Execute 'COPIER>OPTION>COMBO> (1) PPR-SLCT (paper type) / (2) MOD-SLCT
(paper pick-up mode) / (3) ENV-SLCT (environment selection)' and register them under TR-SW 1 to 5.
2. Execute 'COPIER>ADJUST>HV-TR> (1) TR-TP-TM (length of application time) / (2) TR-TP-LV
(application level).'
SW for the setting of transfer lead edge weak bias (paper pick-up mode)
1: One-sided (Default)
2: Second side of the paper picked up from a cassette
3: Second side of the paper manually fed
<Additional information>
The transfer lead edge weak bias becomes effective with the following settings.
1. Output condition: Execute 'COPIER>OPTION>COMBO> (1) PPR-SLCT (paper type) / (2) MOD-SLCT
(paper pick-up mode) / (3) ENV-SLCT (environment selection)' and register them under TR-SW 1 to 5.
2. Execute 'COPIER>ADJUST>HV-TR> (1) TR-TP-TM (length of application time) / (2) TR-TP-LV
(application level).'
SW for the setting of transfer lead edge weak bias (environment selection)
<Setting range>
1: Low humidity
2: Rather low humidity
3: Normal humidity (Default: 3)
4: Rather high humidity
5: High humidity
<Additional information 1>
The setting of '17 becomes valid in all environments only for iR3570/3570F/4570/4570F/iR3530/4530.
<Additional information 2>
The transfer lead edge weak bias becomes effective with the following settings.
1.Output condition: Execute 'COPIER>OPTION>COMBO> (1) PPR-SLCT (paper type) / (2) MOD-SLCT
(paper pick-up mode) / (3) ENV-SLCT (environment selection)' and register them under TR-SW 1 to 5.
2.Execute 'COPIER>ADJUST>HV-TR> (1) TR-TP-TM (length of application time) / (2) TR-TP-LV
(application level).'
SW 1/2/3/4/5 for the setting of transfer lead edge weak bias
<Setting range>
0: OFF (Default)
1: ON
Register the following setting under this switch.
COPIER>OPTION>COMBO>PPR-SLCT/MOD-SLCT/ENV-SLCT
How to use this mode
1) Set a required combination of the 3 service modes shown above.
2) Select any of TR-SW 1 through 5.
3) Set the selected switch to '1'.
* The transfer lead edge weak bias becomes effective under this condition.
** When you select one of TR-SW 1 through 5 while setting any of them to '1', the setting of the selected
switch is displayed under OPIER>OPTION>COMBO>PPR-SLCT/MOD-SLCT/ENV-SLCT.
The transfer lead edge weak bias becomes effective with the settings shown above and below.
COPIER>ADJUST>HV-TR (1) TR-TP-TM (length of application time) / (2) TR-TP-LV (application level)
Sub-item
Displaying the send function installation status in transfer invalidation and executing
transfer invalidation
Acquiring a transfer license key for the send function in transfer invalidation
Description
T-16-57
COPIER >OPTION > COMBO
Description
T-16-58
COPIER >OPTION >LCNS-TR
Description
Chapter 16
Level
2
Level
1
1
1
1
Level
2
2
16-47