1. Press the counter check key on the control panel, and then press "Device Configuration" to check if a printer option is displayed on any of the software

option fields. Note that the Printer Expansion Kit-A1 can be checked in this field, however, the UFR II Printer Kit-E3 cannot be checked. If no option is

displayed in the field, go to the step2.

2. In service mode [COPIER > ACC-STS > PDL-FNC1], check the value of each bit displayed. Starting from the left, each bit shows the following in

sequence: BDL, PS. PCL, PDF, LIPS, N201, I5577, ESC/P, HPGL, HPGL2, IMAGING, and KS. (The remaining bits are reserved.) If a printer option has

been extended, the corresponding bit is set to "1".

14.2.10.1.55 Are all destinations in Address Book deleted when RAM on Main controller PCB is cleared?

iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 / / / /

[ Manual-related ]

Description

All destinations registered in the address book and all service data are deleted when the data of RAM on the DC controller PCB is cleared in the service mode.

When clearing the RAM data, follow the procedure below in advance to keep all the destinations in the address book and all service data.

a. Backup of all destinations in Address Book to a PC

In the Remote UI screen [Add. Func. > Import/Export > Address Book > Export > Start Export].

b. Backup of all service data

In service mode [COPIER > FUNCTION < MISC-P > P-PRINT], output all the service mode values as a P-Print.

14.2.10.1.56 How many sheets of paper can be loaded on Buffer Pass Unit-E1?

iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 / / / /

[ Manual-related ]

Description

The number of sheets that can be loaded on the buffer pass unit-E1 is as follows:

- A4/A5R/LTR/STMTR size paper: 100 sheets at a maximum

- A3/A4R/LDR/LGL/LTRR size paper: 50 sheets at a maximum

14.2.10.1.57 Horizontal registration adjustment is not as required even after adjusting cassette position: 2-Cassette Pedestal-Y2

iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 / / / /

[ Case in the field ]

Description

At time of installation, horizontal registration adjustment is performed by executing the cassette position adjustment and the service mode adjustment.

Therefore, when horizontal registration adjustment is not as required under the set of standards even after executing the cassette position adjustment, follow

the procedure below to enter the horizontal registration adjustment value in service mode.

Field Remedy

In serviced mode (Level2) [COPIER > ADJUST > MISC > C3-ADJ-Y (for cassette 3)/C4-ADJ-Y (for cassette 4) > enter a value > OK]. This will change

the laser write start position for paper fed from a cassette. An increase of '1' will increase the front margin by 0.1mm. (Adjustment range: -128 to 127, the

value at time of factory shipment:0)

14.2.10.1.58 DADF-N1: Adjustments to be required when installing DADF-N1

iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 / / / /

[ Case in the field ]

Description

The following adjustments are required when installing DADF-N1.

Field Remedy

When installing the DADF-N1, make the following eight adjustments referring to the installation manual that comes with the unit.

1. Height adjustment

2. Tray width adjustment

3. Right angle adjustment

4. Read position adjustment

5. Magnification adjustment

6. Horizontal registration adjustment

7. Trailing edge registration adjustment

8. White level adjustment

14.2.10.1.59 DADF-N1: Scanning operation in different size originals mode

iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 / / / /

[ Case in the field ]

Description

When selecting the different size originals mode as a special feature of a copying job and scanning either of the following combination of original size from

the DADF-N1; LTR and LDR, LTRR and LGL, STMT and LTRR, or LGL and STMT, if "Same Width" is selected in the copy screen [Special Features >

Different Size Originals], the machine feeds the originals as if it scans two-sided originals. However, if "Different Width" is selected under Special Features,

the machine never operates in such a manner.