Canon iR3570 Service Manual page 654

Chapter 16
DC-CON
R-CON
JAM-HIST
ERR-HIST
PWD-CLR
ADRS-BK
CNT-MCON
CNT-DCON
OPTION
MMI
MN-CON
CARD
ALARM
16-28
COPIER > FUNCTION > CLEAR
Sub-item
Clearing RAM on the DC controller circuit board
The RAM is cleared when the main power switch is turned OFF and ON.
<Operating procedure>
1) Select COPIER>FUNCTION>MISC-P>P-PRINT to print out the contents of
the service mode.
2) Select this item and press the OK key.
3) Turn the main power switch OFF and ON.
4) Enter the P-PRINT output data as required.
Clearing RAM on the reader controller circuit board
The RAM is cleared when the main power switch is turned OFF and ON.
<Operating procedure>
1) Select COPIER>FUNCTION>MISC-P>P-PRINT to print out the contents of
the service mode.
2) Select this item and press the OK key.
3) Turn the main power switch OFF and ON.
4) Enter the P-PRINT output data as required.
Clearing the jam history
The jam history is cleared when the OK key is pressed.
<Operating procedure>
1) Select this item and press the OK key.
Clearing the error history
The error history is cleared when the OK key is pressed.
<Operating procedure>
1) Select this item and press the OK key.
Clearing the password of the system administrator set in user mode
The password is cleared when the OK key is pressed.
<Operating procedure>
1) Select this item and press the OK key.
Clearing the address book on the reader controller circuit board
The address book is cleared when the main power switch is turned OFF and ON.
<Operating procedure>
1) Select this item and press the OK key.
2) Turn the main power switch OFF and ON.
Clearing the service counter incremented by the main controller circuit board
The password is cleared when the OK key is pressed.
<Operating procedure>
1) Select this item and press the OK key.
Clearing a service counter incremented by the DC controller circuit board
The password is cleared when the OK key is pressed.
This applies to SORT, FIN-STPR, SADDLE, and SDL-STPL under
COPIER>COUNTER>DRBL-2.
<Operating procedure>
1) Select this item and press the OK key.
Resetting a service mode (OPTION) to default (values after RAM clearance)
The service mode is reset when the OK key is pressed.
This clears data in the main controller, DC controller, and reader controller.
<Operating procedure>
1) Select COPIER>FUNCTION>MISC-P>P-PRINT to print the contents of the
service mode.
2) Select this item and press the OK key.
Clearing the following settings in User mode
- Backup data (user-defined values) for copy operations
- Backup data (user-defined values) of common settings
- Various backup data (user-defined values), excluding fax
The settings are cleared when the main power switch is turned OFF and ON.
<Operating procedure>
1) Select this item and press the OK key.
2) Turn the main power switch OFF and ON.
Clearing RAM on the main controller circuit board
The RAM is cleared when the main power switch is turned OFF and ON.
<Operating procedure>
1) Select COPIER>FUNCTION>MISC-P>P-PRINT to print the contents of the
service mode.
2) Select this item and press the OK key.
3) Turn the main power switch OFF and ON.
4) Enter the P-PRINT output data as required.
Clearing the card ID (department) related data
The card ID related data is cleared when the main power switch is turned OFF and
ON.
<Operating procedure>
1) Select this item and press the OK key.
2) Turn the main power switch OFF and ON.
Clearing the alarm log
The alarm log is cleared when the main power switch is turned OFF and ON.
<Operating procedure>
1) Select this item and press the OK key.
2) Turn the main power switch OFF and ON.
Description Level
1
1
1
1
1
1
1
1
1
1
1
1
1