Error Code Details - Canon LBP351 Series Service Manual

Error Code Details

Error Code Title
A4-nn-Error System error
A5-nn-Error System error
A7-nn-Error System error
D0-nn-Error System error
D7-nn-Error System error
D8-nn-Error System error
D9-nn-Error System error
F9-nn-Error System error
E000-0000 Fixing temperature
rising error
E001-0000 Abnormally high
fixing temperature
1
E001-0001 Abnormally high
fixing temperature
2
E003-0000 Abnormally low fix-
ing temperature de-
tection 1
E003-0001 Abnormally low fix-
ing temperature de-
tection 2
Detection description
System error
System error
System error
System error
System error
System error
System error
Communication error be-
tween the Main Controller and
the Control Panel
Temperature of the Main
Thermistor did not become
the specified temperature al-
though the specified time had
passed.
The Main Thermistor detec-
ted a temperature higher than
the specified temperature.
The Sub Thermistor detected
a temperature higher than the
specified temperature.
Temperature of the Main
Thermistor was lower than the
specified temperature when
the heater was ON.
Temperature of the Sub Ther-
mistor 1 was lower than the
specified temperature when
the heater was ON.
- Turn OFF and then ON the main power. If the error persists, obtain
the following information and contact the department in charge of
quality management. - Output STATUS PRINT/P-PRINT. - Collect
Sublog - Collect information on conditions to reproduce the error -
Obtain user's print data (binary data)
- Turn OFF and then ON the main power. If the error persists, obtain
the following information and contact the department in charge of
quality management. - Output STATUS PRINT/P-PRINT. - Collect
Sublog - Collect information on conditions to reproduce the error -
Obtain user's print data (binary data)
- Turn OFF and then ON the main power. If the error persists, obtain
the following information and contact the department in charge of
quality management. - Output STATUS PRINT/P-PRINT. - Collect
Sublog - Collect information on conditions to reproduce the error -
Obtain user's print data (binary data)
- Turn OFF and then ON the main power. If the error persists, obtain
the following information and contact the department in charge of
quality management. - Output STATUS PRINT/P-PRINT. - Collect
Sublog - Collect information on conditions to reproduce the error -
Obtain user's print data (binary data)
- Turn OFF and then ON the main power. If the error persists, obtain
the following information and contact the department in charge of
quality management. - Output STATUS PRINT/P-PRINT. - Collect
Sublog - Collect information on conditions to reproduce the error -
Obtain user's print data (binary data)
- Turn OFF and then ON the main power. If the error persists, obtain
the following information and contact the department in charge of
quality management. - Output STATUS PRINT/P-PRINT. - Collect
Sublog - Collect information on conditions to reproduce the error -
Obtain user's print data (binary data)
- Turn OFF and then ON the main power. If the error persists, obtain
the following information and contact the department in charge of
quality management. - Output STATUS PRINT/P-PRINT. - Collect
Sublog - Collect information on conditions to reproduce the error -
Obtain user's print data (binary data)
- Check for any poor contact/open circuit of the connector between
the Main Controller and the Control Panel. If there is no problem with
the connector but the error persists, obtain the following information
and contact the department in charge of quality management. - Out-
put STATUS PRINT/P-PRINT. - Collect Sublog - Collect information
on conditions to reproduce the error
1. Check the drawer connector between the Fixing Assembly and
the Power Supply PCB. 2. Replace the Fixing Assembly. 3. Replace
the Power Supply PCB.
1. Check the drawer connector between the Fixing Assembly and
the Power Supply PCB. 2. Replace the Fixing Assembly. 3. Replace
the Power Supply PCB.
1. Check the drawer connector between the Fixing Assembly and
the Power Supply PCB. 2. Replace the Fixing Assembly. 3. Replace
the Power Supply PCB.
1. Check the drawer connector between the Fixing Assembly and
the Power Supply PCB. 2. Replace the Fixing Assembly. 3. Replace
the Power Supply PCB.
1. Check the drawer connector between the Fixing Assembly and
the Power Supply PCB. 2. Replace the Fixing Assembly. 3. Replace
the Power Supply PCB.
155
8. Error/Jam/Alarm
Remedy