Canon iR3570 Service Manual page 648

Chapter 16
RG-HF-SP
ADJ-RE-L
LOOP-THK
LOOP-SP
LOOP-ENV
<CST-ADJ>
MF-A4R
MF-A6R
MF-A4
<FIXING>
FX-FL-SP
FX-FL-TH
FX-FL-LW
<MISC>
16-22
COPIER > ADJUST > FEED-ADJ
Sub-item
Adjusting the registration clutch ON timing
<Setting range> -128 to 127 (Default: 0)
If RAM on the DC controller circuit board has been cleared or the board itself
has been replaced, enter the value from the service label.
Adjusting the horizontal registration at paper re-feed (Large paper)
- If the image is deviated to this side, increase the value.
<Setting range> -128 to 127 (Default: 0)
If RAM on the DC controller circuit board has been cleared or the board itself
has been replaced, enter the value from the service label.
Adjusting the registration loop amount at thick-paper feed
<Setting range> -128 to 127 (Default: 0)
A higher setting will increase the degree of paper arching. (unit:0.1mm)
Adjusting the registration loop amount at special-paper feed
<Setting range> -128 to 127 (Default: 0)
A higher setting will increase the degree of paper arching. (unit:0.1mm)
Adjusting the registration loop amount at envelope feed from a cassette
<Setting range> -128 to 127 (Default: 0)
A higher setting will increase the degree of paper arching. (unit:0.1mm)
COPIER > ADJUST > CST-ADJ
Sub-item
Entering the basic paper width of the manual feed tray (A4R)
<Setting range> 0 to 1024 (Default: 516)
If RAM on the DC controller circuit board has been cleared or the board itself has
been replaced, enter the value from the service label.
For replacing the paper with detection VR or registering a new value for the firs
time, this service mode shall be executed by FUNCTION>CST.
Entering the basic paper width of the manual feed tray (A6R)
<Setting range> 0 to 1024 (Default: 175)
If RAM on the DC controller circuit board has been cleared or the board itself has
been replaced, enter the value from the service label.
For replacing the paper with detection VR or registering a new value for the firs
time, this service mode shall be executed by FUNCTION>CST.
Entering the basic paper width of the manual feed tray (A4)
<Setting range> 0 to 1024 (Default: 791)
If RAM on the DC controller circuit board has been cleared or the board itself has
been replaced, enter the value from the service label.
For replacing the paper with detection VR or registering a new value for the firs
time, this service mode shall be executed by FUNCTION>CST.
Sub-item
Entering a fine adjustment value for the fixing film speed when plain paper is
used.
Make a fine adjustment of the target control speed for the fixing film speed when
plain paper is used.
<Setting range> -3 to 3 (Default: 0) (Unit: ms)
If RAM on the DC controller circuit board has been cleared or the board itself has
been replaced, enter the value from the service label.
Entering a fine adjustment value for the fixing film speed when thick paper is
used.
Make a fine adjustment of the target control speed for the fixing film speed when
thick paper is used.
<Setting range> -3 to 3 (Default: 0) (Unit: ms)
If RAM on the DC controller circuit board has been cleared or the board itself has
been replaced, enter the value from the service label.
Entering a fine adjustment value for the fixing film speed when low-speed plain
paper is used.
Make a fine adjustment of the target control speed for the fixing film speed when
low-speed plain paper is used.
<Setting range> -3 to 3 (Default: 0) (Unit: ms)
If RAM on the DC controller circuit board has been cleared or the board itself has
been replaced, enter the value from the service label.
Description
T-16-29
Description
T-16-30
COPIER > ADJUST > FIXING
Description
Level
1
1
2
2
2
Level
1
1
1
Level
2
2
2