Canon iR3570 Service Manual page 658

Chapter 16
FIX-TEMP
TRANS-SW Switching transfer high-voltage control from constant current control to constant
TEMP-CON Switching the thick paper fixing temperature mode
PRIAC-SW Improving the image quality in case of a drum charging fault
TEMPCON
2
CONFIG
W/SCNR
16-32
Sub-item
Switching the plain paper down sequence table
<Setting range>
0: OFF (Default)
1: Prioritize productivity. Set the control temperature at -20 deg C across the board.
2: Set the control temperature at -10 deg C across the board.
3: It is -20Åé only in case of 21Åé or more in room temperature as for the control
temperature.
4: It is -10Åé only in case of 21Åé or more in room temperature as for the control
temperature.
5: Set the control temperature at +6 deg C across the board.
6: Set the control temperature at +10 deg C across the board.
7: Set the control temperature at +15 deg C across the board.
(For DCON Ver.15 or later)
<Additional information>
This can be set with TEMP-COM or TEMPCON2.
Example)
When FIX-TEMP is set to -6 deg C and TEMP-COM is set to -6 deg C , the control
temperature is offset by -12 deg C .
voltage control
<Setting range>
0: No switching [Default], 1: Constant voltage mode 1, 2: Constant voltage mode 2
<Setting range>
0: OFF (Default)
1: Prioritize productivity. Set the control temperature at -10 deg C across the board.
2: Set the control temperature at -6 deg C across the board.
3: Set the control temperature at -3 deg C across the board.
4: Prioritize fixing performance. Set the control temperature at +3 deg C across the
board.
5: Set the control temperature at +6 deg C across the board.
6: Set the control temperature at +10 deg C across the board.
7: Set the control temperature at +15 deg C across the board.
<Additional information>
This can be set with FIX-TEMP.
When FIX-TEMP is set to -6 deg C and TEMP-COM is set to -6 deg C, the control
temperature is offset by -12 deg C.
Note: This setting is cleared if APVC is executed with a new drum unit or if a
service mode (FUNCTION>D-GAMMA) is executed.
<Setting range>
0: No UP [Default], 1: 50 mA UP, 2: 100 mA UP
Improving fixing (Increasing the fixing temperature)
Switching the multiple plain paper fixing temperature mode
<Note>
This is only valid for iR3530/3570/3570F/4530/4570/4570F.
<Setting range>
0: OFF (Default)
1: Prioritize productivity. Set the control temperature at -10 deg C across the board.
2: Set the control temperature at -6 deg C across the board.
3: Set the control temperature at -3 deg C across the board.
4: Prioritize fixing performance. Set the control temperature at +3 deg C across the
board.
5: Set the control temperature at +6 deg C across the board.
6: Set the control temperature at +10 deg C across the board.
7: Set the control temperature at +15 deg C across the board.
<Additional information>
This can be set with FIX-TEMP.
When FIX-TEMP is set to -6 deg C and TEMPCOM2 is set to -6 deg C, the control
temperature is offset by -12 deg C.
Selecting several types of firmware installed on the hard disk and switching the
country, language, and paper size type of this machine
<Adjustment method>
XXYYZZAAXX: Country (UP), YY: Language (ja), ZZ(00) Destination, AA(00):
Paper size type
The display contents conform to the display method of
(COPIER>DISPLAY>USER>LANGUAGE). Enclosed in the brackets are
defaults. The country and language are only displayed.
<Operating procedure>
1) Select <CONFIG>.
2) Select an item to reverse its display. Then press the + or - key to change the
contents.
3) Each time the + or - key is pressed, the contents change sequentially.
4) Display the intended contents at all items and press the OK key.
5) Turn the main power switch OFF and ON.
Setting whether a scanner is present (Copy model)
<Setting range>
0: Printer model [Default]
1: Model with scanner
COPIER > OPTION > BODY
Description Level
1
1
1
1
1
1
1