Canon imageRUNNER ADVANCE C350 series Service Manual page 911

COPIER> OPTION> IMG-FIX
FXS-TM11 Image leading edge control temp: rcycl 1
Lv.1 Details To set the offset of image leading edge control temperature for
recycled paper 1 (64 to 75 g/m2).
As the value is incremented by 1, the control temperature is
increased by 5 deg C from the specified value.
Increase the value when a fixing failure occurs on the leading edge
of paper.
Decrease the value when uneven gloss occurs on the leading edge
(56.5 mm).
Use case - When a fixing failure occurs on the leading edge of paper
- When uneven gloss occurs on the leading edge (56.5 mm)
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to change the value a little at a time. Otherwise, offset/image
failure occurs when setting an extreme value.
Display/adj/set range -2 to 2
-2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: +5 deg C, 2: +10 deg C
Unit 5 deg C
Default value 0
FXS-TM12 Image leading edge control temp: pln 3
Lv.1 Details To set the offset of image leading edge control temperature for plain
paper 3 (91 to 105 g/m2).
As the value is incremented by 1, the control temperature is
increased by 5 deg C from the specified value.
Increase the value when a fixing failure occurs on the leading edge
of paper.
Decrease the value when uneven gloss occurs on the leading edge
(56.5 mm).
Use case When uneven gloss occurs on the leading edge (56.5 mm) of plain
paper 3
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to change the value a little at a time. Otherwise, offset/image
failure occurs when setting an extreme value.
Display/adj/set range -2 to 2
-2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: +5 deg C, 2: +10 deg C
Unit 5 deg C
Default value 0
8
Service Mode > COPIER > OPTION > IMG-FIX
8 Service Mode > COPIER > OPTION > IMG-FIX
COPIER> OPTION> IMG-FIX
FXS-TM13 Image leading edge control temp: rcycl 2
Lv.1 Details To set the offset of image leading edge control temperature for
recycled paper 2 (76 to 90 g/m2).
As the value is incremented by 1, the control temperature is
increased by 5 deg C from the specified value.
Increase the value when a fixing failure occurs on the leading edge
of paper.
Decrease the value when uneven gloss occurs on the leading edge
(56.5 mm).
Use case - When a fixing failure occurs on the leading edge of paper
- When uneven gloss occurs on the leading edge (56.5 mm)
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to change the value a little at a time. Otherwise, offset/image
failure occurs when setting an extreme value.
Display/adj/set range -2 to 2
-2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: +5 deg C, 2: +10 deg C
Unit 5 deg C
Default value 0
FXS-TM14 Image leading edge control temp: rcycl 3
Lv.1 Details To set the offset of image leading edge control temperature for
recycled paper 3 (91 to 105 g/m2).
As the value is incremented by 1, the control temperature is
increased by 5 deg C from the specified value.
Increase the value when a fixing failure occurs on the leading edge
of paper.
Decrease the value when uneven gloss occurs on the leading edge
(56.5 mm).
Use case - When a fixing failure occurs on the leading edge of paper
- When uneven gloss occurs on the leading edge (56.5 mm)
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to change the value a little at a time. Otherwise, offset/image
failure occurs when setting an extreme value.
Display/adj/set range -2 to 2
-2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: +5 deg C, 2: +10 deg C
Unit 5 deg C
Default value 0
8-141
8-141