Canon imageRUNNER ADVANCE C350 series Service Manual page 688

Table of Contents

Advertisement

Error
Detail
Location
Item
code
Code
E537 0001 02
Title
Rear Alignment Motor error
Detection
The Rear Alignment Motor did not move from the HP.
description
Remedy
1. Check that the connector (P7-5/P7/J7) of the Rear Alignment
Plate HP Sensor (S5) is not disconnected.
2. Check that the connector (P5-13/P5-3/J5-3/P5/J5) of the
Rear Alignment Motor (M5) is not disconnected.
3. Replace the Rear Alignment Plate HP Sensor (S5).
4. Replace the Rear Alignment Motor (M5).
5. Check the conditions of the rear alignment drive parts (belt
and gear).
6. Replace the Finisher Controller PCB.
7. Replace the Harness Assembly.
E537 0002 02
Title
Rear Alignment Motor error
Detection
The Rear Alignment Motor did not return to the HP.
description
Remedy
1. Check that the connector (P7-5/P7/J7) of the Rear Alignment
Plate HP Sensor (S5) is not disconnected.
2. Check that the connector (P5-13/P5-3/J5-3/P5/J5) of the
Rear Alignment Motor (M5) is not disconnected.
3. Replace the Rear Alignment Plate HP Sensor (S5).
4. Replace the Rear Alignment Motor (M5).
5. Check the conditions of the rear alignment drive parts (belt
and gear).
6. Replace the Finisher Controller PCB.
7. Replace the Harness Assembly.
E540 0001 02
Title
Stack Tray Shift Motor timeout
Detection
Timeout
description
Remedy
1. Check that the connector (P8-11/P8-1/J8-1/J8) of the Stack
Tray Paper Height Sensor (S9) is not disconnected.
2. Check that the connector (J14-3/P14-3/P14/J14) of the Stack
Tray Shift Motor (M8) is not disconnected.
3. Replace the Stack Tray Paper Height Sensor (S9).
4. Replace the Stack Tray Shift Motor (M8).
5. Check the conditions of the stack tray shift motor drive parts
(belt and gear).
6. Replace the Finisher Controller PCB.
7. Replace the Harness Assembly.
7
Error•Jam•Alarm > Error Code > Error Code Details
Description
7
Error•Jam•Alarm > Error Code > Error Code Details
Error
Detail
Location
Item
code
Code
E575 0001 02
Title
Gripper Motor error
Detection
The Gripper Motor did not move from the HP.
description
Remedy
1. Check that the connector (P7-14/P7-6/J7-6/P7/J7) of the
Gripper HP Sensor (S7) is not disconnected.
2. Check that the connector (P6-3/J6-3/P6/J6) of the Gripper
Motor (M7) is not disconnected.
3. Replace the Gripper HP Sensor (S7).
4. Replace the Gripper Motor (M7).
5. Check the conditions of the gripper drive parts (belt and
gear).
6. Replace the Finisher Controller PCB.
7. Replace the Harness Assembly.
E575 0002 02
Title
Gripper Motor error
Detection
The Gripper Motor did not return to the HP.
description
Remedy
1. Check that the connector (P7-14/P7-6/J7-6/P7/J7) of the
Gripper HP Sensor (S7) is not disconnected.
2. Check that the connector (P6-3/J6-3/P6/J6) of the Gripper
Motor (M7) is not disconnected.
3. Replace the Gripper HP Sensor (S7).
4. Replace the Gripper Motor (M7).
5. Check the conditions of the gripper drive parts (belt and
gear).
6. Replace the Finisher Controller PCB.
7. Replace the Harness Assembly.
E575 0004 02
Title
Gripper clock error
Detection
Clock error
description
Remedy
1. Check that the connector (P13-1/P13/J13) of the Gripper
Encoder Sensor (S8) is not disconnected.
2. Replace the Gripper Encoder Sensor (S8).
E577 0001 02
Title
Paddle Motor error
Detection
The Paddle Motor did not move from the HP.
description
Remedy
1. Check that the connector (P8-4/P8/J8) of the Paddle HP
Sensor (S3) is not disconnected.
2. Check that the connector (P5-4/P5/J5) of the Paddle Motor
(M3) is not disconnected.
3. Replace the Paddle HP Sensor (S3).
4. Replace the Paddle Motor (M3).
5. Check the conditions of the paddle drive parts (gear).
6. Replace the Finisher Controller PCB.
7. Replace the Harness Assembly.
7-74
Description
7-74

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents