Canon imageRUNNER ADVANCE C350 series Service Manual page 887

COPIER> FUNCTION> MISC-P
FX-RG-H Exe of ppr side rgst displace check mode
Lv.2 Details To execute the mode to check side registration displacement of
paper based on the position at the Fixing Assembly.
By executing this item, a paper is picked up from the paper source
specified by FX-RGPOS and it stops at the position where a
specified length of it comes out from the Fixing Assembly.
Adjust the paper position at pickup side (inside a cassette) based on
the side registration position at that time.
Use case When feeding speed of A4 size paper is decreased
Adj/set/operate method 1) Specify a paper source by FX-RGPOS.
2) Select the item, and then press OK key.
A paper stops at the Fixing Assembly.
3) Turn OFF the main power switch.
4) Remove the Fixing Assembly, and check the side registration
position of the paper.
5) Pull out the paper, and install the Fixing Assembly.
6) Turn ON the main power switch.
7) Enter 0, and then press OK key.
8) Execute mechanical adjustment using the Adjustment Plate in a
cassette to adjust the side registration position of paper.
9) Repeat the above procedure as needed.
Caution Be sure to set A4 paper on the paper source (Cassette 2 to 4, Multi-
purpose Tray) specified by FX-RGPOS.
Related service mode COPIER> FUNCTION> MISC-P> FX-RGPOS
FX-RGPOS Spec ppr src at side reg displc ppr chck
Lv.2 Details To specify the paper source that is used for checking side registration
displacement of paper.
After setting A4R paper on the specified paper source, execute
COPIER> FUNCTION> MISC-P> FX-RG-H.
Use case When feeding speed of A4 size paper is decreased
Adj/set/operate method Enter the setting value, and then press OK key.
Caution Be sure to set A4 paper on the specified paper source.
Display/adj/set range 1 to 5
1: Cassette 1, 2: Cassette 2, 3: Cassette 3, 4: Cassette 4, 5: Multi-
purpose Tray
Related service mode COPIER> FUNCTION> MISC-P> FX-RG-H
OPF-DSEQ Set of DADF pickup noise reduction
Lv.2 Details To set whether to control drive noise that is generated when picking
up paper (plain paper, thin paper, etc.) from DADF at 1/1 speed.
When 1 is set, noise is alleviated, but productivity is decreased (A4R,
35 ppm -> 32.2 ppm).
The setting is not applied to pickup at 1/2 speed (heavy paper).
Use case Upon user's request (to alleviate noise)
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
8
Service Mode > COPIER > FUNCTION > SYSTEM
T-8-35
8 Service Mode > COPIER > FUNCTION > SYSTEM
■ SYSTEM
COPIER> FUNCTION> SYSTEM
DOWNLOAD Shift to download mode
Lv.1 Details To make the machine enter the download mode and wait for a
command.
Perform downloading by SST.
Use case At upgrade
Adj/set/operate method 1) Select the item, and then press OK key.
2) Perform downloading by SST/USB.
Caution Do not turn OFF the power before HOLD is displayed.
Display/adj/set range When waiting for a command: STAND-BY/STNDBY, In
communication: CONNECTED, Communication terminated: HOLD
Supplement/memo SST: Service Support Tool
CHK-TYPE HD-CLEAR/HD-CHECK exe partition No.
Lv.1 Details To specify the partition number of the HDD to execute HD-CLEAR/
HD-CHECK.
Since the partition number on the Flash side cannot be specified,
specify the partition number on the HDD side that is also deleted
when E614 (Flash error) occurs.
Use case When specifying the repair area at occurrence of E614/E602 (file
corruption, HDD failure, etc.)
Adj/set/operate method Enter the value, and then press OK key.
Display/adj/set range 0 to 32
0: Entire HDD/related Flash area
1 to 32: Target partition number of the HDD
1: System area *1
2: SWAP (temporary file/memory alternative area) *1
3: MEAP-related storage area
4: Not used *1
5: Image data storage area *2
6: PDL-related file storage area
7: Image data storage area *2
8: PDL spool data (temporary file) *3
9: General application storage area (temporary file) *3
10: SEND-related data storage area
11: General application storage area *3
12: Update-related area *3
13: License-related area *1
14: Debug log-related area *3
15 to 32: Not used
*1: The area is not cleared even if HD-CLEAR is executed.
*2: Although which area is specified, HD-CLEAR/HD-CHECK is
executed to both areas.
*3: Although which area is specified, HD-CLEAR/HD-CHECK is
executed to all of the areas.
Default value 0
Related service mode COPIER> FUNCTION> SYSTEM> HD-CLEAR, HD-CHECK
8-117
8-117