Canon imageRUNNER ADVANCE C350 series Service Manual page 909

COPIER> OPTION> IMG-FIX
TMP-TBL7 Fixing control temperature:Plain paper 2
Lv.1 Details To set the offset of fixing control temperature for plain paper 2 (76 to
90 g/m2).
As the value is incremented by 1, the control temperature is
increased by 5 deg C from the specified value.
Increase the value when a fixing failure occurs.
Decrease the value when fixing offset occurs.
Use case When offset/fixing failure occurs on plain paper 2
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to change the value a little at a time. Otherwise, offset/image
failure occurs when setting an extreme value.
Display/adj/set range -2 to 2
-2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: +5 deg C, 2: +10 deg C
Unit 5 deg C
Default value 0
TMP-TBL8 Fixing control temperature:Transparency
Lv.1 Details To set the offset of fixing control temperature for transparency.
As the value is incremented by 1, the control temperature is
increased by 5 deg C from the specified value.
Increase the value when a fixing failure occurs.
Decrease the value when fixing offset occurs.
Use case When offset/fixing failure occurs on transparency
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to change the value a little at a time. Otherwise, offset/image
failure occurs when setting an extreme value.
Display/adj/set range -2 to 2
-2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: +5 deg C, 2: +10 deg C
Unit 5 deg C
Default value 0
8
Service Mode > COPIER > OPTION > IMG-FIX
8 Service Mode > COPIER > OPTION > IMG-FIX
COPIER> OPTION> IMG-FIX
FXS-TMP7 Image leading edge control temp: pln 2
Lv.1 Details To set the offset of image leading edge control temperature for plain
paper 2 (76 to 90 g/m2).
As the value is incremented by 1, the control temperature is
increased by 5 deg C from the specified value.
Increase the value when a fixing failure occurs on the leading edge
of paper.
Decrease the value when uneven gloss occurs on the leading edge
(56.5 mm).
Use case When uneven gloss occurs on the leading edge (56.5 mm) of plain
paper 2
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to change the value a little at a time. Otherwise, offset/image
failure occurs when setting an extreme value.
Display/adj/set range -2 to 2
-2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: +5 deg C, 2: +10 deg C
Unit 5 deg C
Default value 0
FXS-TMP8 Image leading edge control temp: transp
Lv.1 Details To set the offset of image leading edge control temperature for
transparency.
As the value is incremented by 1, the control temperature is
increased by 5 deg C from the specified value.
Increase the value when a fixing failure occurs on the leading edge
of paper.
Decrease the value when uneven gloss occurs on the leading edge
(56.5 mm).
Use case When uneven gloss occurs on the leading edge (56.5 mm) of
transparency
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to change the value a little at a time. Otherwise, offset/image
failure occurs when setting an extreme value.
Display/adj/set range -2 to 2
-2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: +5 deg C, 2: +10 deg C
Unit 5 deg C
Default value 0
8-139
8-139