Canon imageRUNNER ADVANCE C350 series Service Manual page 866

COPIER> ADJUST> HV-TR
T2TR-N1 Adj of lead edge weak bias: pln ppr 1
Lv.2 Details To adjust the offset of the leading edge weak bias for plain paper 1.
Decrease the value if white spots occur.
Increase the value if density on the leading edge of paper is low
(transfer is weak).
Use case When an image failure (white spots at the leading edge) occurs
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Caution Use this item only when an image failure occurs.
Display/adj/set range -128 to 127
Unit 30 V
Default value 0
T2TR-N2 Adj of lead edge weak bias: pln ppr 2
Lv.2 Details To adjust the offset of the leading edge weak bias for plain paper 2.
Decrease the value if white spots occur.
Increase the value if density on the leading edge of paper is low
(transfer is weak).
Use case When an image failure (white spots at the leading edge) occurs
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Caution Use this item only when an image failure occurs.
Display/adj/set range -128 to 127
Unit 30 V
Default value 0
T2TR-N3 Adj of lead edge weak bias: pln ppr 3
Lv.2 Details To adjust the offset of the leading edge weak bias for plain paper 3.
Decrease the value if white spots occur.
Increase the value if density on the leading edge of paper is low
(transfer is weak).
Use case When an image failure (white spots at the leading edge) occurs
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Caution Use this item only when an image failure occurs.
Display/adj/set range -128 to 127
Unit 30 V
Default value 0
8
Service Mode > COPIER > ADJUST > HV-TR
8 Service Mode > COPIER > ADJUST > HV-TR
COPIER> ADJUST> HV-TR
T2TR-R1 Adj of lead edge weak bias: rcycl ppr 1
Lv.2 Details To adjust the offset of the leading edge weak bias for recycled paper
1.
Decrease the value if white spots occur.
Increase the value if density on the leading edge of paper is low
(transfer is weak).
Use case When an image failure (white spots at the leading edge) occurs
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Caution Use this item only when an image failure occurs.
Display/adj/set range -128 to 127
Unit 30 V
Default value 0
T2TR-R2 Adj of lead edge weak bias: rcycl ppr 2
Lv.2 Details To adjust the offset of the leading edge weak bias for recycled paper
2.
Decrease the value if white spots occur.
Increase the value if density on the leading edge of paper is low
(transfer is weak).
Use case When an image failure (white spots at the leading edge) occurs
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Caution Use this item only when an image failure occurs.
Display/adj/set range -128 to 127
Unit 30 V
Default value 0
T2TR-R3 Adj of lead edge weak bias: rcycl ppr 3
Lv.2 Details To adjust the offset of the leading edge weak bias for recycled paper
3.
Decrease the value if white spots occur.
Increase the value if density on the leading edge of paper is low
(transfer is weak).
Use case When an image failure (white spots at the leading edge) occurs
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Caution Use this item only when an image failure occurs.
Display/adj/set range -128 to 127
Unit 30 V
Default value 0
8-96
8-96