Canon imageRUNNER ADVANCE C350 series Service Manual page 927

COPIER> OPTION> NETWORK
IFX-CHIG Set operation by IFAX recv e-mail text
Lv.1 Details To set the number of characters for the IFAX received mail content,
so that the mail is not printed/forwarded when the characters in the
text is less than the number of specified characters.
This machine can output blank paper because some senders send
e-mail text consists of linefeed codes only. In such case, specify 2
(number of characters) so that there will be no output of blank paper.
In the case of specifying any number other than 0, header/footer is
printed/forwarded in 1 sheet only if the e-mail (body) text is less than
the specified value while no TIFF file is attached.
As the value is incremented by 1, the number of target characters in
e-mail body text is increased by 1 character.
Use case When reducing print of blank paper due to e-mail received by IFAX.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to get approval from the user by telling that there will be no
print of e-mail (body) text if the number of characters is less than the
specified value.
Display/adj/set range 0 to 999
0: E-mail (body) text is not ignored.
Unit 1 char
Default value 0
Supplement/memo 1 Japanese Kanji character is calculated as 2 bytes, and the control
codes (such as linefeed code, etc) are included in the number of
characters.
DNSTRANS Setting of DNS transfer priority
Lv.1 Details To set priority order of the protocol (IPv4/IPv6) to be used for DNS
query.
In the case of using both IPv6 and IPv4 while the DNS server
supports IPv4, it takes time because of timeout when executing DNS
query with priority on IPv6.
Giving priority on query by IPv4 can shorten the time.
Use case When it takes time to execute DNS query with priority on IPv6
because the DNS server supports IPv4
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: IPv4, 1: IPv6
Default value 1
8
Service Mode > COPIER > OPTION > NETWORK
8 Service Mode > COPIER > OPTION > NETWORK
COPIER> OPTION> NETWORK
PROXYRES Setting of proxy response to Windows
Lv.2 Details To set whether to provide proxy response or return the device status
when an inquiry is received via Windows while the device is in sleep
mode.
Use case When executing status response for query from Windows correctly
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: No proxy response, 1: Proxy response
Default value 1
WOLTRANS Setting of sleep recovery protocol
Lv.1 Details To set the protocol for recovery from sleep mode according to the
value of WOL (Wake On LAN) trans.
Reception of a specific network packet is one of the requirements for
the device to recover from sleep mode.
When the number of network protocols supported by the device
increases, the types of network packets which activate recovery from
sleep mode vary. However, there is a possibility that the existing
network protocol is actually used.
Select the type of network packet which activates recovery from
sleep mode according to the environment where the device is used.
Use case When selecting protocol for sleep recovery
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 1 to 3
1: WSD and SNMP, 2: WSD and CPCA, 3: CPCA and SNMP
Default value 1
802XTOUT Set of IEEE802.1X authentication timeout
Lv.1 Details To set timeout value for IEEE802.1X authentication.
If the device executes 802.1X authentication, change the wait time
for response from the authentication server.
Use case When response from the authentication server is slow/fast
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 10 to 120
Unit 1 second
Default value 30
IKERETRY Setting of IKE retry times
Lv.1 Details To set the number of retries in the case of no response from the
communication target at the time of IKE packet transmission.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 3
Default value 1
Supplement/memo IKE: Internet Key Exchange
8-157
8-157