Canon imageRUNNER ADVANCE C350 series Service Manual page 872

COPIER> ADJUST> FEED-ADJ
REG-MFH2 Adj ppr lead edge margin: heavy 3, MP
Lv.1 Details To adjust the leading edge margin by changing the timing to turn ON
the Registration Motor when feeding heavy paper 3 from the Multi-
purpose Tray.
As the value is changed by 1, the leading edge margin is changed by
0.1 mm.
+: Leading edge margin becomes smaller. (An image moves
upward.)
-: Leading edge margin becomes larger. (An image moves
downward.)
When replacing the DC Controller PCB/clearing RAM data, either
restore the backup data or enter the value of service label.
Use case - When adjusting the leading edge margin
- When replacing the DC Controller PCB/clearing RAM data
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Caution If data is not backed up before replacing the DC Controller PCB/
clearing RAM data, enter the value of service label.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value The value differs according to the product configuration.
LP-FEED3 Adj of per-rest arch amount: 2/3 speed
Lv.1 Details To adjust the arch amount before registration at 2/3 speed.
The setting is applied in case of pickup from a cassette/Multi-purpose
Tray and 1-sided/2-sided printing.
As the value is incremented by 1, the arch amount changes by 0.1
mm.
+: Increase
-: Decrease
Use case When adjusting the arch amount before registration at 2/3 speed
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -20 to 20
Unit 0.1 mm
Default value 0
8
Service Mode > COPIER > ADJUST > FEED-ADJ
8 Service Mode > COPIER > ADJUST > FEED-ADJ
COPIER> ADJUST> FEED-ADJ
REG-MENV Adj ppr lead edge margin: envelope, MP
Lv.1 Details To adjust the leading edge margin by changing the timing to turn
ON the Registration Motor when feeding envelope from the Multi-
purpose Tray.
As the value is changed by 1, the leading edge margin is changed by
0.1 mm.
+: Leading edge margin becomes smaller. (An image moves
upward.)
-: Leading edge margin becomes larger. (An image moves
downward.)
When replacing the DC Controller PCB/clearing RAM data, either
restore the backup data or enter the value of service label.
Use case - When adjusting the leading edge margin
- When replacing the DC Controller PCB/clearing RAM data
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Caution If data is not backed up before replacing the DC Controller PCB/
clearing RAM data, enter the value of service label.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value The value differs according to the product configuration.
REG-ENV Adj ppr lead edge margin: envelope, cst
Lv.1 Details To adjust the leading edge margin by changing the timing to turn ON
the Registration Motor when feeding envelope from a cassette.
As the value is changed by 1, the leading edge margin is changed by
0.1 mm.
+: Leading edge margin becomes smaller. (An image moves
upward.)
-: Leading edge margin becomes larger. (An image moves
downward.)
When replacing the DC Controller PCB/clearing RAM data, either
restore the backup data or enter the value of service label.
Use case - When adjusting the leading edge margin
- When replacing the DC Controller PCB/clearing RAM data
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Caution If data is not backed up before replacing the DC Controller PCB/
clearing RAM data, enter the value of service label.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value The value differs according to the product configuration.
8-102
8-102