Canon imageRUNNER ADVANCE C350 series Service Manual page 905

COPIER> OPTION> DSPLY-SW
WT-WARN Dspl/hide of Wst Tonr Cntner prep mssg
Lv.1 Details To set whether to display the preparation warning message of the
Waste Toner Container on the status area of LUI.
Use case When there is no need to notify the preparation timing of the Waste
Toner Container to the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Hide, 1: Display
Default value 1
Related service mode COPIER> OPTION> CUSTUM> EXT-TBOX
DF-DSP Dspl/hide DADF Roll counter initial scrn
Lv.1 Details To set whether to display the DADF Roller on the counter initialization
screen in Settings/Registration.
Use case When the user does not replace the parts
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: Hide, 1: Display
Default value 1
2TR-DSP Dspl/hide Sec Trn Out Rol cntr init scrn
Lv.1 Details To set whether to display the Secondary Transfer Outer Roller on the
counter initialization screen in Settings/Registration.
Use case When the user does not replace the parts
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: Hide, 1: Display
Default value 0
DRM-DSP Cntr initial screen dspl sw: Drum Unit
Lv.1 Details To set whether to display/hide the Drum Unit in the counter initial
screen in Settings/Registration.
Use case When the customer replaces the parts
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: Hide, 1: Display
Default value 0
Related UI menu Settings/Registration> Adjustment/Maintenance> Maintenance>
Initialize After Replacing Parts> Drum Unit
8
Service Mode > COPIER > OPTION > IMG-FIX
T-8-39
8 Service Mode > COPIER > OPTION > IMG-FIX
■ IMG-FIX
COPIER> OPTION> IMG-FIX
NEGA-GST ON/OFF of pre-exposure operation
Lv.2 Details To set whether to execute pre-exposure operation at warm-up
rotation/paper interval when ghost due to negatively charged drum
occurs.
Use case When ghost due to negatively charged drum occurs
Adj/set/operate method Enter the setting value, and then press OK key.
Caution Be sure to get approval from the user in advance by telling that
productivity decreases.
Display/adj/set range 0 to 2
0: OFF, 1: ON (at warm-up rotation only), 2: Not used
Default value 0
FX-S-TMP Image leading edge control temp: pln 1
Lv.1 Details To set the offset of image leading edge control temperature for plain
paper 1 (60 to 75 g/m2).
As the value is incremented by 1, the control temperature is
increased by 5 deg C from the specified value.
Increase the value when a fixing failure occurs on the leading edge
of paper.
Decrease the value when uneven gloss occurs on the leading edge
(56.5 mm).
Use case When uneven gloss occurs on the leading edge (56.5 mm) of plain
paper 1
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to change the value a little at a time. Otherwise, offset/image
failure occurs when setting an extreme value.
Display/adj/set range -2 to 2
-2: -10 deg C, -1: -5 deg C, 0: 0 deg C, 1: 5 deg C, 2: 10 deg C
Unit 5 deg C
Default value 0
8-135
8-135