Canon imageRUNNER ADVANCE C350 series Service Manual page 958

TEST
■ PG
COPIER> TEST> PG
TYPE Test print
Lv.1 Details To execute the test print.
Use case At trouble analysis
Adj/set/operate method Enter the setting value, and then press OK key.
Test print is executed.
Caution Be sure to return the value to 0 after the test print output.
Display/adj/set range 0 to 100
0: Image from CCD (normal print)
1 to 3: For R&D use
4: 16 gradations
5: Halftone for all areas
6: Grid
7 to 9: For R&D use
10: MCYBk horizontal line
11: For R&D use
12: YMCBk 64 gradations
13: For R&D use
14: Full color 16 gradations
15 to 100: For R&D use
Default value 0
TXPH Setting of test print image mode
Lv.1 Details To set the image mode at the time of test print output.
This mode is enabled for test print only.
Use case At trouble analysis
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 14
0: Error diffusion
1: Low screen ruling (approx. 133 to 190 lines)
2: High screen ruling (approx. 200 to 268 lines)
3 to 4: Not used
5: Error diffusion (with trailing edge adjustment)
6: High screen ruling (with trailing edge adjustment)
7 to 8: Not used
9: 1/2 speed, low screen ruling (approx. 133 to 190 lines)
10: 1/2 speed, high screen ruling (approx. 200 to 268 lines)
11 to 13: Not used
14: 1/2 speed, high screen ruling (with trailing edge adjustment)
8
Service Mode > COPIER > TEST > PG
8 Service Mode > COPIER > TEST > PG
COPIER> TEST> PG
THRU Image correction table use at test print
Lv.1 Details To set whether to use the image correction table at the time of test
print output.
Use case At trouble analysis
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: Used, 1: Not used
DENS-Y Adj of Y-color density at test print
Lv.1 Details To adjust Y-color density when performing test print (TYPE=5).
As the value is increased, the density becomes higher.
Use case At test print (TYPE=5)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 255
Default value 128
DENS-M Adj of M-color density at test print
Lv.1 Details To adjust M-color density when performing test print (TYPE=5).
As the value is increased, the density becomes higher.
Use case At test print (TYPE=5)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 255
Default value 128
DENS-C Adj of C-color density at test print
Lv.1 Details To adjust C-color density when performing test print (TYPE=5).
As the value is increased, the density becomes higher.
Use case At test print (TYPE=5)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 255
Default value 128
DENS-K Adj of Bk-color density at test print
Lv.1 Details To adjust Bk-color density when performing test print (TYPE=5).
As the value is increased, the density becomes higher.
Use case At test print (TYPE=5)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 255
Default value 128
COLOR-Y Y-color output setting at test print
Lv.1 Details To make a setting of Y-color output for test print.
The setting is applied to all types.
When setting "COLOR-Y" to 1 and other items to "0", a single Y-color
is output.
Use case At test print
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: Not output, 1: Output
Default value 1
8-188
8-188