Omron CS1D DUPLEX SYSTEM - 10-2009 Operation Manual page 520

Specifications of Basic I/O Units and High-density I/O Units
CS1W-OD262 Transistor Output Unit (64 Points, Sourcing)
Rated Voltage
Operating Load Voltage
Range
Maximum Load Current
Leakage Current
Residual Voltage
ON Response Time
OFF Response Time
Load Short-circuit Prevention
Insulation Resistance
Dielectric Strength
No. of Circuits
Internal Current Consumption 5 V DC 390 mA max.
External Power Supply
Weight
Accessories
Circuit Configuration
Terminal Connections
484
24 V DC
20.4 to 26.4 V DC
0.3 A/point, 1.6 A/common, 6.4 A/Unit
0.1 mA max.
1.5 V max.
0.5 ms max.
1.0 ms max.
Detection current: 0.7 to 2.5 A
Automatic restart after error clearance. (Refer to page 499.)
20 M between the external terminals and the GR terminal (100 V DC)
1,000 V AC between the external terminals and the GR terminal for 1 minute at a leakage
current of 10 mA max.
64 (16 points/common, 4 circuits)
20.4 to 26.4 V DC, 130 mA max.
270 g max.
Two connectors for external wiring (soldered)
SW
Output indicator
ERR indicator
When overcurrent is detected, the ERR indicator will light. At the same time, the corre-
sponding flag (one for each common) in the Basic I/O Unit Information Area (A050 to
A089) will turn ON.
CN1
I/O word "m+1" I/O word "m"
B A
20 20
COM1 (+V) COM0 (+V)
19 19
0 V 0 V
L 18 18 L
15 15
17 17
L L
14 14
16 16
L L
13 13
15 15
L L
12 12
14 14
L L
11 11
13 13
L L
10 10
12 12
L L
9 9
11 11
L L
8 8
10 10
COM1 (+V) COM0 (+V)
9 9
0 V 0 V
L 8 8 L
7 7
L 7 7 L
24 VDC 6 6
L 6 6 L
5 5
L 5 5 L
4 4
4 4
L L
3 3
3 3
L L
2 2
2 2
L L
1 1
1 1
L L
0 0
• When wiring, pay careful attention to the polarity of the external power supply. The load
may operate if the polarity is reversed.
• Although the COM(+V) and 0V of rows A and B of CN1 and CN2 are internally con-
nected, wire all points completely.
COM0 (+V)
COM0 (+V)
A
OUT00
to
OUT15
CN1
0 V
COM1 (+V)
COM1 (+V)
OUT00
B
to
OUT15
0 V
COM2 (+V)
COM2 (+V)
A
OUT00
to
OUT15
CN2
0 V
COM3 (+V)
COM3 (+V)
OUT00
B
to
OUT15
0 V
CN2
I/O word "m+2"
A B
0 0
1 1
L
1 1
2 2
L
2 2
3 3
L
3 4 4 3
L
4 4
L 5 5
5 5
6 6
L
24 VDC
6 6
L 7 7
7 7
L 8 8
0V 0V
9 9
COM2 (+V) COM3 (+V)
10 10
8 8
11 11
L
9 9
12 12
L
10 10
13 13
L
11 11
14 14
L
24 VDC
12 12
15 15
L
13 16 16 13
L
14 17 17 14
L
15 15
L 18 18
0 V 0 V
19 19
COM2 (+V) COM3 (+V)
20 20
Appendix A
I/O word "m+3"
L
L
L
L
L
24 VDC
L
L
L
L
L
L
L
L
L
L
L