Mitsubishi Electric MELSEC iQ-R Series User Manual page 169

Message
Message discarded because spooling
is disabled
Cyclic measurement cancelled
Sending cancelled due to offline (1)
Sending cancelled due to offline (2)
Sending cancelled due to offline (3)
Sending cancelled due to line
disconnection (1)
Sending cancelled due to line
disconnection (2)
Sending cancelled due to line
disconnection (3)
Dialog interrupted due to dialog
violation
Dialog monitoring target
T1 timeout error
T2 timeout error
T3 timeout error
T4 timeout error
T6 timeout error
T7 timeout error
T8 timeout error
T9 timeout error
Reception notification trigger not set
Unclear secondary reception
*2
Abort reception (transfer continued)
Abort reception (transfer interrupted)
*1 Displayed for only the MELSEC-Q series SECS/GEM communication software pre-installed model module.
*2 Appears in the non-GEM version only.
Description
A spooled sending message requested during spooling was
discarded because spooling is disabled.
Although the cyclic message sending request trigger is ON,
sending was cancelled due to an offline status, etc.
Although a message sending request trigger was detected,
sending was not performed because the status was offline.
Although a message sending request trigger was detected, a
message was not created since the status was offline and the
message is a non-spooled message.
Although a message sending request trigger was detected, a
message was not created because the status was offline and
the spooling is disabled.
Although a message sending request trigger was detected,
the message was not sent because the line is disconnected.
Although a message sending request trigger was detected,
the message was not created because the line is
disconnected and the message is a non-spooled message.
Although a message sending request trigger was detected, a
message was not created because the line is disconnected
and spooling is disabled.
A message with the response message monitoring (dialog)
setting was sent, but a notification was received from the host
regarding a message other than the one subject to
monitoring.
This error is output in combination with "Dialog interrupted
due to dialog violation" or "T9 timeout error".
T1 timeout
T2 timeout
T3 timeout
T4 timeout
T6 timeout
T7 timeout
T8 timeout
T9 timeout
Although there is a format definition, notification of message
reception is not possible since the reception notification
trigger is disabled.
A secondary message that is not transaction-monitored by the
SECS/GEM communication software has been received.
An abort message was received during spool transmission.
*2
An abort message was received during spool transmission.
Notes
Check the Enable spooling relay. Note that the
Enable spooling relay can be configured only by a
non-GEM version.
• Offline, line disconnected, spooling in progress
(excluding cases where the message is a spooled
message)
• An error is output periodically until either the
status changes to sending enabled or the request
trigger is turned OFF. (Measurement resumes
once the status changes to sending enabled.)
• An attempt was made to send a message other
than S1F1 while offline.
• Cyclic messages are excluded.
• When the "Spool during offline" option is enabled
• Cyclic messages are excluded.
• When the "Spool during offline" option is enabled
• Cyclic messages are excluded.
This error is for secondary messages only.
Cyclic messages are excluded.
Cyclic messages are excluded.
The output SF is the one of the sending message
with the dialog setting.
The SF output is the one of the monitoring target
configured to dialog.
Only for SECS-
Only for SECS-
S9F9 sending
Only for SECS-
Only for HSMS
Only for HSMS
Only for HSMS
The output SF is the one of the sending message
with the dialog setting.
For primary messages, an abort is returned after
detection of this error.
For secondary messages, this error is not detected.
• A T3 timeout already occurred for the secondary
message.
• The SF code does not match the code of the sent
primary message (the stream is different; the
function is not primary message +1).
• A response was returned from the host for a
primary message without a wait bit.
• The host sent a message with even-numbered
functions as a primary message.
Issued when configuring "Skip and continue
transfer" for "Abort Reception Upon Spooling" in the
spool common setting.
Issued when setting "Transmit Is Interrupted To Hold
Message" for "Abort Reception Upon Spooling" in
the spool common setting.
7 BASIC FUNCTIONS
7.17 Log Output
7
167