Yamaha A3000 Owner's Manual page 357

Name Range Contents
Loop number 0—16383 Loop number
16383 ($7F, $7F) means to delete all loops
Loop type $00/$01/$7F Loop type
$00= forward only
$01= backward/forward
$7F= loop off
Loop start address 0—2097151 Loop start address (word units)
Loop end address 0—2097151 Loop end address (word units)
If the sample contains a release loop, this message is transmitted after the sample dump.
Alternatively, this message is transmitted in reply to a Loop Point Request message.
4.2.2. Loop Point Request
0 11110000 F0
1 01111110 7E
2 0nnnnnnn nnnnnnn = Channel Number
3 00110100 05
4 00110100 02
5 0sssssss sssssss = Sample number (LSB first)
6 0sssssss sssssss =
7 0bbbbbbb bbbbbbb = Loop number(LSB first)
8 0bbbbbbb bbbbbbb =
9 11110111 F7
This message requests loop points.
Name Range Contents
Loop number 0—16383 Loop number
16383 ($7F, $7F) requests all loops
This message is only received.
4.3. INQUIRY MESSAGE
4.3.1. Identity Request
0 11110000 F0
1 01111110 7E
2 0nnnnnnn nnnnnnn = Channel Number
3 00110100 06
4 00110100 01
5 11110111 F7
This message requests device-specific information.
4.3.2. Identity Reply
0 11110000 F0
1 01111110 7E
2 0nnnnnnn nnnnnnn = Channel Number
3 00110100 06
4 00110100 02
5 01000011 43 = Manufacturers System Exclusive ID code
6 0fffffff fffffff = Device family code(LSB first)
7 0fffffff fffffff =
8 0ddddddd ddddddd = Device family number code(LSB first)
9 0ddddddd ddddddd =
10 0vvvvvvv vvvvvvv = Software revision level. Format device specific
11 0vvvvvvv vvvvvvv = (LSB first)
12 0vvvvvvv vvvvvvv =
13 0vvvvvvv vvvvvvv =
14 11110111 F7
This message is returned in response to an Identity Request message asking for device-specific informa-
tion.
Name Range Contents
Device family code 0041 LM
Device family number code 0116 #0278
Software revision level 0100-nnnn A3000 software version
This message is only transmitted in response to an Identity Request message.
5. YAMAHA SYSTEM EXCLUSIVE
5.1. Bulk dump
This message is transmitted when an editing operation "Bulk" is executed, when the MIDI UTILITY
"Bulk" operation is executed, or when a dump request is received.
This message can be received if bulk protect is off.
Data format
0 11110000 F0
1 01000011 43
2 0000nnnn nnnn = Device Number
3 00001010 7A
4 0bbbbbbb
number of bytes
5 0bbbbbbb
6 01001100 4C(ASCII"L")
7 01001101 4D(ASCII"M")
8 00100000 20(ASCII" ")
9 00100000 20(ASCII" ")
10 00110000 30(ASCII"0")
11 00110001 32(ASCII"2")
12 00110000 37(ASCII"7")
13 00110000 38(ASCII"8")
14 0mmmmmmm mmmmmmm = data format name ending (ASCII)
15 0mmmmmmm mmmmmmm = data format name ending (ASCII)
16 0ccccccc
object name(ASCII)
31 0ccccccc
32 0ddddddd ddddddd = data
0sssssss sssssss = check_sum
11110111 F7
The data format name ending in bytes 14 and 15 specifies the type of bulk data, as follows.
mm Data type
SY System parameter bulk dump
PG Program bulk dump
SB Sample bank bulk dump
SP Sample bulk dump
WD Wave data bulk dump
SQ Sequence bulk dump
OL Object list bulk dump
Note) mm is ASCII code
"Object name" is the name attached to the bulk dump. However for system parameters and object lists,
this will always be eight bytes of 20 (ASCII " ").
If a bulk dump is 4096 bytes or more including the header, data will be divided into packets of 4096, and
all data will be transmitted in the above format.
Data bytes are divided in the order of upper nibble and lower nibble. For details on the data contents, refer
to table 1.
MIDI data format
Appendix
355