Chrysler RAM TRUCK 2500 1994 Service Manual page 758

• 3.9L ENGINE 9 - 37
(6) Lightly oil the new lower seal lips with engine
oil.
(7) Install the new lower rear bearing oil seal into
the bearing cap with the yellow paint facing towards
the rear of the engine.
(8) Apply 5 mm (0.20 in) drop of Loctite 515, or
equivalent, on each side of the rear main bearing cap
(Fig. 7). DO NOT over apply sealant or allow the
sealant to contact the rubber seal. Assemble bearing
cap to cylinder block immediately after sealant appli­
cation.
(9) To align the bearing cap, use cap slot, align­
ment dowel and cap bolts. DO NOT remove excess
material after assembly. DO NOT strike rear cap
more than 2 times for proper engagement.
(10) Clean and oil all cap bolts. Install all main
bearing caps. Install all cap bolts and alternately
tighten to 115 N-m (85 ft. lbs.) torque.
(11) Install oil pump.
(12) Apply Mopar Silicone Rubber Adhesive Seal­
ant, or equivalent, at bearing cap to block joint to
provide cap to block and oil pan sealing (Fig. 8). Ap­
ply enough sealant until a small amount is squeezed
out. Withdraw nozzle and wipe excess sealant off the
oil pan seal groove.
(13) Install new front crankshaft oil seal.
(14) Immediately install the oil pan.
UPPER SEAL REPLACEMENT (CRANKSHAFT
INSTALLED!
(1) Remove the oil pan.
(2) Remove the oil pump from the rear main bear­
ing cap.
(3) Remove the rear main bearing cap. Remove
and discard the old lower oil seal.
(4) Carefully remove and discard the old upper oil
seal.
(5) Clean the cylinder block mating surfaces before
oil seal installation.
(6) Lightly oil the new upper seal lips with engine
oil. To allow ease of installation of the seal, loosen at
least the 2 main bearing caps forward of the rear
bearing cap.
(7) Rotate the new upper seal into the cylinder
block being careful not to shave or cut the outer sur­
face of the seal. To assure proper installation, use the
installation tool provided with the kit. Install the
new seal with the yellow paint facing towards the
rear of the engine.
(8) Install the new lower rear bearing oil seal into
the bearing cap with the yellow paint facing towards
the rear of the engine.
(9) Apply 5 mm (0.20 in) drop of Loctite 515, or
equivalent, on each side of the rear main bearing cap
(Fig. 7). DO NOT over apply sealant or allow the
sealant to contact the rubber seal. Assemble bearing
cap to cylinder block immediately after sealant appli­
cation. Be sure the yellow paint faces toward the rear
of the engine.
(10) To align the bearing cap, use cap slot, align­
ment dowel and cap bolts. DO NOT remove excess
material after assembly. DO NOT strike rear cap
more than 2 times for proper engagement.
(11) Install the rear main bearing cap with cleaned
and oiled cap bolts. Alternately tighten A L L cap bolts
to 115 N-m (85 ft. lbs.) torque.
(12) Install oil pump.
(13) Apply Mopar Silicone Rubber Adhesive Seal­
ant, or equivalent, at bearing cap to block joint to
provide cap to block and oil pan sealing (Fig. 8). Ap­
ply enough sealant until a small amount is squeezed
out. Withdraw nozzle and wipe excess sealant off the
oil pan seal groove.
(14) Immediately install the oil pan.
LOWER SEAL REPLACEMENT
(1) Remove the oil pan.
(2) Remove the oil pump from the rear main bear­
ing cap.
(3) Remove the rear main bearing cap and discard
the old lower seal.
(4) Clean the rear main cap mating surfaces i n ­
cluding the oil pan seal grooves.
(5) Carefully install a new upper seal (refer to Up­
per Seal Replacement - Crankshaft Installed proce­
dure above).
(6) Lightly oil the new lower seal lips with engine
oil.
(7) Install a new lower seal i n bearing cap with
yellow paint facing the rear of engine.
(8) Apply 5 mm (0.20 in) drop of Loctite 515, or
equivalent, on each side of the rear main bearing cap
(Fig. 7). DO NOT over apply sealant or allow the
sealant to contact the rubber seal. Assemble bearing
cap to cylinder block immediately after sealant appli­
cation.
(9) To align the bearing cap, use cap slot, align­
ment dowel and cap bolts. DO NOT remove excess
material after assembly. DO NOT strike rear cap
more than 2 times for proper engagement.
(10) Install the rear main bearing cap with cleaned
and oiled cap bolts. Alternately tighten the cap bolts
to 115 N-m (85 ft. lbs.) torque.
(11) Install oil pump.
(12) Apply Mopar Silicone Rubber Adhesive Seal­
ant, or equivalent, at bearing cap to block joint to
provide cap to block and oil pan sealing (Fig. 8). Ap­
ply enough sealant until a small amount is squeezed
out. Withdraw nozzle and wipe excess sealant off the
oil pan seal groove.
(13) Immediately install the oil pan.
CYLINDER BLOCK
Remove the engine assembly from the vehicle.