Chrysler RAM TRUCK 2500 1994 Service Manual page 808

(7) After removal, install bearing cap on the mat­
ing rod.
INSPECTION
Check the crankshaft connecting rod journal for ex­
cessive wear, taper and scoring.
Check the cylinder block bore for out-of-round,
taper, scoring and scuffing.
Check the pistons for taper and elliptical shape be­
fore they are fitted into the cylinder bore (Fig. 3).
DIAMETER (D)
SHOULD BE
0.0000-0.0152 mm
(0.0000-0.0006 in.
LARGER THAN (C)
98.704-98.831 mm
(3.886-3.891 in.)
ELLIPTICAL SHAPE OF THE PISTON
SKIRT SHOULD BE 0.254-0.304 mm
(0.010-0.012 in.) LESS AT DIAMETER
(A) THAN ACROSS THE THRUST
FACES AT DIAMETER (B).
J9309-9
Fig. 3 Piston Measurements
FITTING PISTONS
Piston and cylinder wall must be clean and dry.
Specified clearance between the piston and the cylin­
der wall is 0.013-0.038 mm (0.0005-0.0015 inch).
Piston diameter should be measured at the top of
skirt, 90° to piston pin axis. Cylinder bores should be
measured halfway down the cylinder bore and trans­
verse to the engine crankshaft center line.
Pistons and cylinder bores should be measured at
normal room temperature, 21°C (70°F).
FITTING R I N G S
(1) Measurement of end gaps:
(a) Measure piston ring gap 2 inches from bot­
tom of cylinder bore. An inverted piston can be
used to push the rings down to ensure positioning
rings squarely in the cylinder bore before measur­
ing.
(b) Insert feeler stock in the gap. The compres­
sion ring gap should be between 0.254-0.508 mm
(0.010-0.020 inch). The second compression ring
gap should be between 0.508-0.762 mm (0.020-
0.030 inch). The oil ring gap should be 0.254-1.270
mm (0.010-0.050 inch).
(c) Rings with insufficient end gap may be prop­
erly filled to the correct dimension. Rings with ex­
cess gaps should not be used.
(2) Install rings and confirm ring side clearance:
(a) Install oil rings being careful not to nick or
scratch the piston.
(b) Install the compression rings using Installa­
tion Tool C-4184. The top compression may be in­
stalled with either side up. The second compression
ring must be installed with the identification mark
face up (toward top of piston) and the chamfer
should face down. An identification mark on the
ring is a drill point, a stamped letter "O", an oval
depression or the word TOP.
(c) Measure side clearance between piston ring
and ring land (Fig. 4). Clearance should be 0.038-
0.076 mm (0.0015-0.0030 inch) for the compression
rings. The steel rail oil ring should be free in
groove, but should not exceed 0.203 mm (0.0080
inch) side clearance.
FEELER G A U G E
GROOVE
J9209-136
Fig. 4 Measuring Piston Ring Side Clearance
(d) Pistons with insufficient or excessive side
clearance should be replaced.
(3) Arrange ring gaps 90° apart as shown in Fig. 5.
CONNECTING ROD BEARINGS
Fit all rods on a bank until completed. DO NOT al­
ternate from one bank to another, because connecting
rods and pistons are not interchangeable from one
bank to another.
The bearing caps are not interchangeable and
should be marked at removal to ensure correct as­
sembly.
Each bearing cap has a small V-groove across the
parting face. When installing the lower bearing shell,
make certain that the V-groove in the shell is in line
with the V-groove in the cap. This provides lubrica­
tion of the cylinder wall in the opposite bank.
The bearing shells must be installed so that the
tangs are in the machined grooves in the rods and
caps.