Chrysler RAM TRUCK 2500 1994 Service Manual page 843

9 - 122 5.9L (DIESEL) ENGINE
T O R Q U E S P E C I F I C A T I O N S
•
| Description I Torque
75
N
T n
(55 ft. lbs.)
Camshaft Thrust Plate Torx Bolts . . . .
22 N*m (16ft. lbs.)
Coil Pack Bracket Bolts
21 N*m(190in. lbs.)
Connecting Rod Cap Bolts . . . . . . . .
61N*m(45ft. lbs.)
Crankshaft Main Bearing Cap Bolts
1st Step . . . . . . . . . . . .
2nd Step
27N*m(20 ft.
115
N^m
(85 ft.
lbs.)
lbs.)
Crankshaft Pulley/Damper Bolt
183N*m(135 ft. lbs.)
Crankshaft Rear Seal Retainer Bolts . . . . 22N«m(16fr. lbs.)
Cylinder Head Bolts
1st Step
2nd Step
58N*m(43 ft.
143N«m(105 ft.
lbs.)
lbs.)
Cylinder Head Cover Bolts/Studs . . .
16N«m(144in. lbs.)
Drive Plate-to-Crankshaft Bolts . . . . . .
75N*m(55ft. lbs.)
Drive Plate-to-Torque Converter Bolts . . . .75 N*m (55 ft. lbs.)
EGR Tube Nut.
34N*m(25 ft. lbs.)
EGR Bolts
20N*m(174in. lbs.)
Engine Support Bracket/Cushion
Thru-Bolt
102N*m(75 ft. lbs.)
Engine Support Bracket/Cushion
41 N*m(30ft. lbs.)
Exhaust Manifold-to-Cylinder
22N*m(16ft. lbs.)
Flywheel-to-Crankshaft Bolts . . . . . . .
75N#m(55 ft. lbs.)
41 N*m(30ft. lbs.)
Generator-to-intake Manifold
Bracket Bolts
41 N«m(30ft. lbs.)
20N«m(175 in. lbs.)
hydraulic Tappet Yoke Retaining
22N*m(16ft. lbs.)
Intake Manifold Bolts (Lower)
54N*m(40ft. lbs.)
Description | Torque |
Intake Manifold Bolts (Upper) 22 N*m (16 ft. lbs.)
Oil Filter 9 N*m (80 in. lbs.)
+45°
Oil Filter Connector 46 N»m (34 ft. lbs.)
Oil Pan Bolts (1/4-20) 11 N*m (96 in. lbs.)
Oil Pan Stud Bolts . 16 N*m (144 in. lbs.)
Oil Pan Bolts (5/16-18) 16 N*m (144 in. lbs.)
Oil Pan Drain Plug 34 N*m (25 ft. lbs.)
Oil Pan Pick-Up Tube Bolts 16 N*m (144 in. lbs.)
Oil Pump Attaching Bolts 41 N*m (30 ft. lbs.)
Oil Pump Cover Bolts 14 N«m (125 in. lbs.)
Oil Pump Pressure Relief Plug 20 N*m (15 ft. lbs.)
Rear Oil Seal Retainer Bolts . 22 N*m (16 ft. lbs.)
Rocker Arm Bolts . . . . . . . . 28 N*m (21 ft. lbs.)
Spark Plugs 41 N*m (30 ft. lbs.)
Starter Mounting Bolts 68 N«m (50 ft. lbs.)
Timing Chain Cover Bolts 47 N»m (35 ft. lbs.)
Thermostat Housing Bolts 25 N»m (220 in. lbs.)
Throttle Body Nuts 11 N«m (96 in. lbs.)
Torque Converter Drive Plate Bolts 31 N«m (270 in. lbs.)
Transfer Case-to-lnsulator Mounting
Plate Nuts . 2 0 4 N « m (150 ft. lbs.)
Transmission Support Bracket Bolts 68 N«m (50 ft. lbs.)
Transmission Support Cushion Bolts 41 N»m (30 ft. lbs.)
Transmission Support Cushion
Stud Nuts .41 N » m (30 ft. lbs.)
Water Pump-to-Chain Case Cover Bolt . . 41 N*m (30 ft. lbs.)
Water Pump Pulley Bolts . . . . . . . . . . . . 22 N*m (16 ft. lbs.)
J9409-130