Page 1 Town & Country 2 0 1 2 O W N E R ’ S M A N U A L...
Page 2 With respect to any Vehicles Sold in Canada, the name Chrysler This manual illustrates and describes the operation of features and Group LLC shall be deemed to be deleted and the name Chrysler equipment that are either standard or optional on this vehicle. This Canada Inc.
Page 3: Introduction
TABLE OF CONTENTS SECTION PAGE ............3 INTRODUCTION .
Page 5: Table Of Contents
INTRODUCTION CONTENTS Introduction ......4 Vehicle Identification Number ....6 How To Use This Manual .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized Congratulations on selecting your new Chrysler Group dealer knows your vehicle best, has factory-trained tech- LLC vehicle. Be assured that it represents precision nicians and genuine MOPAR parts, and cares about workmanship, distinctive styling, and high quality - all your satisfaction.
Page 7 INTRODUCTION 5...
Page 8: Vehicle Identification Number
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
Page 9: Vehicle Modifications/Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. Stamped VIN Location NOTE: It is illegal to remove or alter the VIN.
Page 11: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Remote Starting System — If Equipped ..30 ▫...
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Enhanced Seat Belt Use Reminder System Sliding Side Door ..... . 46 (BeltAlert ) .
Page 13 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Exhaust Gas ......104 Commercial Cargo Vehicles (No Factory Installed Rear Seats) —...
Page 14: A Word About Your Keys
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Wireless Ignition Node (WIN) with integral ignition switch.
Page 15 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired posi- tion.
Page 16 14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Power window switches will also remain active WARNING! (Continued) for up to 90 seconds after the ignition switch has been • Do not leave the key fob in or near the vehicle, and turned to OFF, depending upon the accessory delay do not leave Keyless Enter-N-Go in the ACC or setting.
Page 17: Sentry Key
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 NOTE: The Key-In-Ignition reminder only sounds seconds for a bulb check. If the light remains on after the when the Key Fob is placed in the OFF or ACC ignition bulb check, it indicates that there is a problem with the position.
Page 18: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE All of the Key Fobs provided with your new vehicle have Duplication of Key Fobs may be performed at an autho- been programmed to the vehicle electronics. rized dealer, this procedure consists of programming a blank Key Fob to the vehicle electronics.
Page 19: Vehicle Security Alarm - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 • This device must accept any interference that may be Rearming Of The System received, including interference that may cause unde- The Vehicle Security Alarm will rearm itself after the 15 sired operation. additional minutes of headlights and Vehicle Security Light flashing, if the Vehicle Security Alarm has not been VEHICLE SECURITY ALARM —...
Page 20 18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Perform one of the following methods to lock the To Disarm The System vehicle: The Vehicle Security Alarm can be disarmed using any of the following methods: • Press LOCK on the interior power door lock switch •...
Page 21 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: you are in the vehicle or not. If you remain in the vehicle • The driver’s door key cylinder and the liftgate button and open a door, the alarm will sound. If this occurs, on the RKE transmitter cannot arm or disarm the disarm the Vehicle Security Alarm.
Page 22: Illuminated Entry - If Equipped
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The illuminated entry system will not operate if the ILLUMINATED ENTRY — IF EQUIPPED The courtesy lights will turn on when you use the dimmer control is in the “dome defeat” position Remote Keyless Entry (RKE) transmitter to unlock the (extreme bottom position).
Page 23: Using The Rke Transmitter
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 NOTE: Inserting the Key Fob with RKE transmitter into Using The RKE Transmitter the ignition switch disables the system from responding Three-button RKE transmitters will provide basic UN- to any button presses from that RKE transmitter. Driving LOCK, LOCK and PANIC functions.
Page 24 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seven-button RKE transmitters will provide functions Remote Unlock Doors And Liftgate that allow the same basic operation as the three-button, Press and release the UNLOCK button on the RKE but may also be used to operate the power liftgate transmitter once to unlock the driver’s side or twice to (optional), power sliding doors, Remote Start feature unlock all doors and liftgate.
Page 25 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 • For vehicles not equipped with the EVIC, the Remote NOTE: Pressing the LOCK button on the RKE transmit- Unlock feature can be enabled or disabled by perform- ter while you are inside the vehicle will activate the ing the following steps: Vehicle Security Alarm.
Page 26 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Settings (Customer-Programmable Features)” in “Un- 5. Repeat these steps if you want to return this feature to derstanding Your Instrument Panel” for further infor- its previous setting. mation. NOTE: Pressing the LOCK button on the RKE transmit- •...
Page 27 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 NOTE: If the vehicle is locked and Vehicle Security Alarm is • When you turn off the Panic Alarm by pressing the armed, using RKE transmitter to open the power liftgate PANIC button a second time, you may have to move does not unlock the vehicle or disarm the Vehicle Security closer to the vehicle due to the Radio Frequency (RF) Alarm.
Page 28 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Open/Close Right Power Sliding Door — If Turn Off Flash Lights With RKE Lock — If Equipped Equipped Press the RIGHT Power Sliding Door button twice on the This feature will cause the turn signal lights to flash when RKE transmitter within five seconds to Power Open/ the doors are locked or unlocked with the RKE transmit- Close the Right Power Sliding Door.
Page 29 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 2. Press and hold the UNLOCK button on a programmed Programming Additional Transmitters RKE transmitter for at least 4 seconds, but no longer than If you do not have a programmed RKE transmitter, 10 seconds.
Page 30 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Remove the emergency key by sliding the mechanical 2. Insert the tip of the emergency key or a #2 flat blade latch at the top of the RKE transmitter sideways with screwdriver into the slot and gently pry the two halves of your thumb and then pull the key out with your other the RKE transmitter apart.
Page 31 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 4. To assemble the RKE transmitter case, snap the two halves together. General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: •...
Page 32: Remote Starting System - If Equipped
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Hood closed REMOTE STARTING SYSTEM — IF EQUIPPED This system uses the Remote Keyless Entry • Liftgate closed (RKE) transmitter to start the engine conve- • Hazard switch off niently from outside the vehicle while still maintaining security.
Page 33 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 • Remote Start Aborted — Hood Ajar WARNING! • Remote Start Aborted — Fuel Low • Do not start or run an engine in a closed garage or • Remote Start Disabled — Start Vehicle To Reset confined area.
Page 34 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The park lights will turn on and remain on during into the ignition switch and move it to the ON/RUN Remote Start mode. position), otherwise the engine will shut off at the end of 15- minute cycle.
Page 35 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Key Fob. Once inserted, the message “Remote Start Cancel Remote Start Active - Key To Run will display in the EVIC until you Remote Starting will also cancel if any of the following insert and turn the key to the ON/RUN position.
Page 36: Door Locks
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: To avoid unintentional shutdowns while in the If the lock knob is down when you shut either front door, Remote Start Mode, the system will not allow the Remote the door will lock. Make sure the keys are not inside the Start button to shut down the engine for two seconds vehicle before closing the door.
Page 37 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 If the lock knob is rearward when you shut either side WARNING! sliding door, the door will lock. Make sure the keys are • For personal security and safety in the event of an not inside the vehicle before closing the door.
Page 38: Power Door Locks - If Equipped
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks — If Equipped the Key Fob or closing the door will allow the locks to A power door lock switch is on each front door trim operate. A chime will sound if the Key Fob is in the panel.
Page 39: Keyless Enter-N-Go
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 If you press the power door lock switch while the sliding The Unlock Doors Automatically On Exit feature will not door is open, the sliding door will lock. operate if there is any manual operation of the power door locks (lock or unlock).
Page 40 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: To Unlock From The Driver’s Side: • Passive Entry may be programmed ON/OFF; refer to With a valid Passive Entry RKE transmitter within 5 ft “Electronic Vehicle Information Center (EVIC)/ (1.5 m) of the driver’s door handle, grab the driver’s front Personal Settings (Customer-Programmable Fea- door handle to unlock the driver’s door automatically.
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 NOTE: If “Unlock All Doors 1st Press” is programmed To Enter The Liftgate all doors will unlock when you grab hold of the driver’s With a valid Passive Entry RKE transmitter within 5 ft front door handle.
Page 42 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Preventing Inadvertent Locking Of Passive Entry RKE To Lock The Vehicle’s Doors Transmitter In Vehicle The front door handles have LOCK buttons located on To minimize the possibility of unintentionally locking a the outside of the handles.
Page 43: Windows
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 With one of the vehicle’s Passive Entry RKE transmitters WINDOWS within 5 ft (1.5 m) of the driver or passenger front door Power Vent Windows — If Equipped handle, press the door handle LOCK button to lock all The Power Vent Window Switch located on the driver’s four doors.
Page 44: Power Windows
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Windows NOTE: Power Window switches will also remain active You can control either the front or rear windows using for up to 10 minutes after the ignition switch has been switches located on the driver’s door trim panel. The turned to OFF, depending upon the accessory delay switches will operate only when the ignition switch is in setting.
Page 45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Power Window Lockout Switch Front Passenger Power Door Switches Front Passenger Power Window Switch 1 - Window Open/Close There is a single switch on the front passenger’s door 2 - Power Door Locks trim panel which operates the passenger door window and a set of switches that lock and unlock all doors.
Page 46 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto-Down Feature — If Equipped To stop the window from going all the way up during the The front window switches may be equipped with an Auto Up operation, push down on the switch briefly. Auto-Down feature.
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 2. Push the window switch down firmly to the second WARNING! detent to open the window completely and continue to hold the switch down for an additional two seconds after There is no anti-pinch protection when the window the window is fully open.
Page 48: Sliding Side Door
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The switches will not operate if the driver has Wind Buffeting activated the Power Window Lockout. Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.
Page 49: Power Sliding Side Door - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 To keep your door operating properly, observe the fol- NOTE: The left side sliding door cannot be opened lowing guidelines: while the fuel door is open. This feature operates only when the sliding door is fully closed prior to opening the •...
Page 50 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Press the button on the RKE transmitter twice within five seconds to open a power sliding door. When the door is fully open, pressing the button twice within five seconds a second time will close the door. There are power sliding side door switches located on the b-pillar trim panel, just in front of the power sliding door for the rear seat passengers and in the overhead console...
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 • If the power sliding door encounters multiple obstruc- master lock button, located in the overhead console, to disable the switches and handles for the rear seat passen- tions within the same cycle, the system will automati- gers.
Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Sliding Side Door Open Flash You can turn the feature back on by repeating the The left and right exterior hazard lights will flash for previous procedure. 12 seconds when either sliding door is opened. This will Power Sliding Side Door Master Lock Switch alert other drivers in the area that passenger(s) could be To provide a safer environment for small children riding...
Page 53: Sliding Side Door Child Protection Lock
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Sliding Side Door Child Protection Lock To provide a safer environment for small children riding in the rear seats, the sliding doors are equipped with a Child Protection Door Lock system. NOTE: When the Child Protection Door Lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position.
Page 54 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Slide the Child Protection Door Lock control inward NOTE: • After engaging the Child Protection Door Lock, al- (toward the vehicle) to engage the Child Protection Door Lock. ways test the door from the inside to make certain it is in the desired position.
Page 55: Liftgate
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 NOTE: WARNING! • After setting the Child Protection Door Lock system, always test the door from the inside to make certain it Avoid trapping anyone in the vehicle in a collision. is in the desired position. Remember that the sliding doors can only be opened from the outside door handle or the switches located •...
Page 56: Power Liftgate - If Equipped
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To open the liftgate, press the liftgate release handle Power Liftgate — If Equipped located on the underside of the license plate bar and pull The power liftgate may be opened manually or by using the liftgate open with one fluid motion.
Page 57 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Overhead Console Master Power Switch Rear Power Liftgate Switch When the RKE transmitter button is pressed and the 1 — Left Door 3 — Right Door 2 — Liftgate 4 — Master Lock Flash Lights feature is enabled, the tail lights will flash and several audible beeps will occur to signal that the The power liftgate may be closed by pressing the button,...
Page 58 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The power liftgate must be in the full open or close WARNING! positions for any of the buttons to operate. If the liftgate is not in the full open or close positions, it must During power operation, personal injury or cargo be opened or closed manually.
Page 59: Occupant Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 • If the power liftgate encounters multiple obstructions OCCUPANT RESTRAINTS within the same cycle, the system will automatically Some of the most important safety features in your stop and must be opened or closed manually. vehicle are the restraint systems: •...
Page 60 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • An energy-absorbing steering column and steering If you will be carrying children too small for adult-sized wheel seat belts, the seat belts or the Lower Anchors and Tether for CHildren (LATCH) feature also can be used to hold •...
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 If a child from 1 to 12 years old (not in a rear facing child WARNING! seat) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint. Infants in rear facing child restraints should never (Refer to “Child Restraints”) ride in the front seat of a vehicle with a passenger...
Page 62 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. If the air bag system in this vehicle needs to be WARNING! (Continued) modified to accommodate a disabled person, contact • Being too close to the steering wheel or instrument the Customer Center. Phone numbers are provided panel during Advanced Front Air Bag deployment under If You Need Assistance .
Page 63: Lap/Shoulder Belts
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Buckle up even though you are an excellent driver, even you under normal conditions. However, in a collision the on short trips. Someone on the road may be a poor driver belt will lock and reduce the risk of you striking the and cause a collision that includes you.
Page 64 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions WARNING! (Continued) 1. Enter the vehicle and close the door. Sit back and • Wearing a seat belt incorrectly is dangerous. Seat adjust the seat. belts are designed to go around the large bones of your body.
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 WARNING! • A belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries.
Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch WARNING! plate into the buckle until you hear a “click”. • A belt that is buckled into the wrong buckle will not protect you properly.
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen.
Page 68 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. Pull the strap down and secure the small latch plate of The belt will automatically retract to its stowed position. the lap belt into the small buckle until you hear a “click”.
Page 69: Seat Belts In Passenger Seating Positions
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 pushing anywhere on the anchorage. To move the an- you will prefer a higher position. When you release the chorage downward, squeeze the actuation buttons while anchorage, try to move it up or down to make sure that simultaneously pushing down on the anchorage assem- it is locked in position.
Page 70: Automatic Locking Retractor Mode (Alr) - If Equipped
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the passenger seating position is equipped with an position that has a belt with this feature. Children ALR and is being used for normal usage: 12 years old and under should always be properly restrained in the rear seat.
Page 71: Energy Management Feature
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Seat Belt Pretensioners WARNING! The seat belts for both front seating positions are • The belt and retractor assembly must be replaced equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. if the seat belt assembly Automatic Locking Re- These devices may improve the performance of the seat tractor (ALR) feature or any other seat belt func-...
Page 72: Supplemental Active Head Restraints (Ahr) - If Equipped
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Active Head Restraints (AHR) — If When AHRs deploy during a rear impact, the front half Equipped of the head restraint extends forward to minimize the gap These head restraints are passive, deployable compo- between the back of the occupant’s head and the AHR.
Page 73 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 CAUTION! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision.
Page 74 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Grasp the deployed AHR from the rear seat. 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. Hand Positioning Points On AHR 2.
Page 75 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 AHR In Reset Position 3 — Final Downward Movement To Engage Locking Mechanism NOTE: 4. The AHR front soft foam and trim half should lock • If you have difficulties or problems resetting the into the back decorative plastic half.
Page 76: Enhanced Seat Belt Use Reminder System (Beltalert )
5 mph (8 km/h), by blinking the Seat Belt BeltAlert can be enabled or disabled by your authorized Reminder Light and sounding an intermittent chime. dealer. Chrysler Group LLC does not recommend deac- Once the sequence starts, it will continue for the entire tivating BeltAlert .
Page 77: Seat Belt Lock Out
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Seat Belt Lock Out extender should be used only if the existing belt is not The center rear seat belt system has a lock out feature that long enough. When it is not required, remove the ex- will not allow you to extract the center webbing unless tender and store it.
Page 78 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In addition, the vehicle is equipped with a Supplemental NOTE: The Driver and Front Passenger Advanced Front Driver Side Knee Air Bag mounted in the instrument Air Bags are certified to the new Federal regulations for panel below the steering column.
Page 79: Air Bag System Components
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 • Air Bag Warning Light and rear passengers sitting next to a window. The SABIC air bags are located above the side windows and their • Steering Wheel and Column covers are also labeled: SRS AIRBAG. •...
Page 80: Advanced Front Air Bag Features
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Advanced Front Air Bag Features WARNING! (Continued) The Advanced Front Air Bag system has multistage • Do not put anything on or around the air bag driver and front passenger air bags. This system provides covers or attempt to open them manually.
Page 81 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Supplemental Side Air Bag Inflatable Curtain (SABIC) SABIC air bags may offer side-impact and vehicle roll- over protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each air bag features inflated chambers placed adjacent to the head of each outboard occupant that reduce the potential for side-impact head injuries.
Page 82 80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The system includes side impact sensors that are cali- Supplemental Driver Side Knee Air Bag brated to deploy the side air bags during impacts that The Supplemental Driver Side Knee Air Bag provides require air bag occupant protection.
Page 83: Air Bag Deployment Sensors And Controls
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Air Bag Deployment Sensors And Controls The Advanced Front Air Bags and Supplemental Driver Side Knee Air Bag will not deploy in all frontal collisions, Occupant Restraint Controller (ORC) including some that may produce substantial vehicle The ORC is part of a Federally regulated safety system damage —...
Page 84 82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat belts are necessary for your protection in all acci- turns on the Air Bag Warning Light, either momentarily dents, and also are needed to help keep you in position, or continuously. A single chime will sound if the light away from an inflating air bag.
Page 85 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 Driver And Passenger Advanced Front Air Bag The Advanced Front Air Bag gas is vented through the Inflator Units vent holes in the sides of the air bag. In this way, the air The Driver and Passenger Advanced Front Air Bag bags do not interfere with your control of the vehicle.
Page 86 84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Seat-Mounted Side Air Bag (SAB) Supplemental Side Air Bag Inflatable Curtain Inflator Units (SABIC) Inflator Units The Supplemental Seat-Mounted Side Air Bags (SAB) are During collisions where the impact is confined to a designed to activate only in certain side collisions.
Page 87 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 • Flash hazard lights as long as the battery has power or Because air bag sensors estimate deceleration over time, vehicle speed and damage are not good indicators of until the ignition key is turned off. whether or not an air bag should have deployed.
Page 88 86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision which deploys the air bags, any throat irritation, move to fresh air. If the irritation or all of the following may occur: continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s in- •...
Page 89 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 Maintaining Your Air Bag System WARNING! (Continued) • Do not attempt to modify any part of your air bag WARNING! system. The air bag may inflate accidentally or • Modifications to any part of the air bag system may not function properly if modifications are could cause it to fail when you need it.
Page 90: Event Data Recorder (Edr)
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Air Bag Warning Light NOTE: If the speedometer, tachometer, or any engine You will want to have the air bags ready to related gauges are not working, the Occupant Restraint inflate for your protection in a collision. The Controller (ORC) may also be disabled.
Page 91: Child Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 • Whether or not the driver and passenger safety belts To read data recorded by an EDR, special equipment is were buckled/fastened; required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, •...
Page 92 90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The infant carrier is only used rearward-facing in the WARNING! vehicle. It is recommended for children from birth until they reach the weight or height limit of the infant carrier. In a collision, an unrestrained child, even a tiny baby, Convertible child seats can be used either rearward- can become a projectile inside the vehicle.
Page 93 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 in the vehicle by the lap/shoulder belt or the LATCH WARNING! child restraint anchorage system. Refer to “Lower An- chors and Tether for CHildren (LATCH)”. Rearward-facing child seats must never be used in the front seat of a vehicle with the front passenger air All children whose weight or height is above the bag.
Page 94 Transport Canada’s web- restraint: site for additional information: http://www.tc.gc.ca/ • Before buying any restraint system, make sure that it roadsafety/safedrivers/childsafety/index.htm has a label certifying that it meets all applicable Safety Standards. Chrysler Group LLC also recommends that...
Page 95 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 you make sure that you can install the child restraint in Installing The Child Restraint System the vehicle where you will use it, before you buy it. We urge you to carefully follow the directions of the manufacturer when installing your child restraint.
Page 96 94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Not all child restraint systems will be installed as we row fold-in-floor seats. Second-row seats also feature have described here. Again, carefully follow the instruc- tether strap anchorages, located in the rear surface of the tions that come with the child restraint system.
Page 97 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 that the seat belts are not toys and should not be NOTE: It is recommended to loosen the top tether strap played with, and never leave your child unattended in and route it loosely prior to securing the lower anchors so the vehicle.
Page 98 96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Tighten the lower attachment strap while firmly push- ing the child restraint rearward and downward into the vehicle seat. Remove all slack in the lower attachment straps. Reference the child restraint instructions for infor- mation on properly removing slack.
Page 99 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 Installing the Top Tether Strap (with either Lower Anchors or Vehicle Seat Belt): 1. Route the top tether strap under the adjustable head restraint between the steel posts. 2. Provide enough slack (reference child restraint in- structions) for the tether strap to reach the tether anchor located near the bottom of the seat back.
Page 100 98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap.
Page 101 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 “Automatic Locking Mode” description under “Seat then allow the belt to retract into the retractor. As the belt Belts in Passenger Seating Positions” section. The chart retracts, you will hear a ratcheting sound. This indicates below defines the seating positions with an Automatic the safety belt is now in the Automatic Locking mode.
Page 102: Commercial Cargo Vehicles (No Factory Installed Rear Seats) - If Equipped
100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transporting Pets WARNING! Air Bags deploying in the front seat could harm your pet. An unrestrained pet could be thrown about and possibly NEVER carry a child in a rear facing infant carrier in injured, or injure a passenger during panic braking or in a vehicle without rear seats.
Page 103: Restraining Infants And Small Children In Commercial Cargo Vehicles
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 This vehicle is equipped with a child restraint tether Restraining Infants And Small Children In anchor located on the lower rear of the front passenger Commercial Cargo Vehicles seat. Use this tether anchor to secure only forward- There are different sizes and types of restraints for facing child restraints equipped with an upper tether children from newborn size to the child almost large...
Page 104 102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Children more than 40 lbs (18 kg) should be secured in 3. Route the tether strap under the head rest. the passenger seat in a child restraint or belt- NOTE: Ensure that the child restraint tether strap is positioning booster seat with the seat adjusted to the centered between the headrest supports underneath the rear most position.
Page 105: Engine Break-In Recommendations
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 103 While cruising, brief full-throttle acceleration within the WARNING! limits of local traffic laws contributes to a good break-in. Wide-open throttle acceleration in low gear can be detri- The vehicle tether anchor is designed to be used with mental and should be avoided.
Page 106: Safety Tips
104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS Exhaust Gas Transporting Passengers WARNING! NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. WARNING! Breathing it can make you unconscious and can •...
Page 107: Safety Checks You Should Make Inside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 105 Safety Checks You Should Make Inside The WARNING! (Continued) Vehicle • If it is necessary to sit in a parked vehicle with the Seat Belts engine running, adjust your heating or cooling Inspect the belt system periodically, checking for cuts, controls to force outside air into the vehicle.
Page 108 106 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defroster WARNING! (Continued) Check operation by selecting the defrost mode and place • Always make sure that floor mats are properly the blower control on high speed. You should be able to attached to the floor mat fasteners.
Page 109: Periodic Safety Checks You Should Make Outside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 107 lodged in the tread or sidewall. Inspect the tread for cuts WARNING! (Continued) and cracks. Inspect sidewalls for cuts, cracks and bulges. • Always make sure that objects cannot fall into the Check the wheel nuts for tightness.
Page 111: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS ▫ Tilt Mirrors In Reverse (Available With Mirrors ......116 Memory Seat Only) —...
Page 112 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Phone Call Features ....139 ▫ Heated Seats — If Equipped ... . 167 ▫...
Page 113 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 ▫ Front Fog Lights — If Equipped ..207 Driver Memory Seat — If Equipped ..196 ▫...
Page 114 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Parksense Display ....222 Tilt/Telescoping Steering Column ..214 ▫...
Page 115 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 ▫ Courtesy/Interior Lighting ... . . 233 ▫ General Information ....245 ▫...
Page 116 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Sunroof Fully Closed ....248 ▫ Driver Seatback Storage — If Equipped ..260 ▫...
Page 117 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Cargo Area Features ....272 Rear Load-Leveling System — If Equipped . . . 274 ▫...
Page 118: Mirrors
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror — If Equipped A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).
Page 119: Outside Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 NOTE: This feature is disabled when the vehicle is CAUTION! moving in reverse. To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.
Page 120: Driver's Automatic Dimming Mirror - If Equipped
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror Folding Feature WARNING! All outside mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have Vehicles and other objects seen in an outside convex three detent positions: full forward, full rearward and mirror will look smaller and farther away than they normal.
Page 121: Heated Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 NOTE: A light in the selected button will illuminate indicating the mirror is activated and can be adjusted. Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move.
Page 122: Tilt Mirrors In Reverse (Available With Memory Seat Only) - If Equipped
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tilt Mirrors In Reverse (Available With Memory Power Folding Mirrors — If Equipped Seat Only) — If Equipped The switch for the power folding mirrors is located Tilt Mirrors in Reverse provides automatic outside mirror between the power mirror switches L (left) and R (right).
Page 123: Blind Spot Monitoring - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Illuminated Mirror Rear Detection Zones BLIND SPOT MONITORING — IF EQUIPPED When the vehicle is started, the BSM warning light will The Blind Spot Monitoring (BSM) system uses two radar- momentarily illuminate in both outside rear view mirrors based sensors, located inside the rear bumper fascia, to to let the driver know that the system is operational.
Page 124 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The BSM system detection zone DOES NOT change if The BSM detection zone covers approximately one lane on both sides of the vehicle (11 ft or 3.35 m). The zone your vehicle is towing a trailer. Therefore, visually starts at the outside rear view mirror and extends ap- verify the adjacent lane is clear for both your vehicle proximately 20 ft (6 m) to the rear of the vehicle.
Page 125 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Sensor Locations BSM Warning Light The BSM system notifies the driver of objects in the The BSM system monitors the detection zone from three detection zones by illuminating the BSM warning light different entry points (side, rear, front) while driving to located in the outside mirrors in addition to sounding an see if an alert is necessary.
Page 126 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Entering From The Side Entering From The Rear Vehicles that move into your adjacent lanes from either Vehicles that come up from behind your vehicle on either side of the vehicle. side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h).
Page 127 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Overtaking Traffic If you pass another vehicle slowly (with a relative speed of less than 10 mph (16 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated.
Page 128 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The BSM system is designed not to issue an alert on The BSM system will not alert you of objects that are stationary objects such as guardrails, posts, walls, foliage, traveling in the opposite direction of the vehicle in berms, etc.
Page 129: Rear Cross Path
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 WARNING! The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones. The BSM system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicle’s mirrors, glance over your shoulder, and use your turn signal before changing lanes.
Page 130: Modes Of Operation
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In a parking lot situation, oncoming vehicles can Modes Of Operation be obscured by vehicles parked on either side. If the Three selectable modes of operation are available in the sensors are blocked by other structures or vehicles, the Electronic Vehicle Information Center (EVIC).
Page 131: Uconnect™ Phone - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 turn signal is then activated, and it corresponds to an Blind Spot Alert Off alert present on that side of the vehicle, an audible chime When the BSM system is turned off there will be no will also be sounded.
Page 132 (be it your purse, pocket, or briefcase), as websites: long as your phone is turned on and has been paired to • www.chrysler.com/uconnect the vehicle’s Uconnect™ Phone. The Uconnect™ Phone allows up to seven mobile phones to be linked to the •...
Page 133 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Voice Command Button WARNING! Actual button location may vary with the ra- dio. The individual buttons are described in the Any voice commanded system should be used only “Operation” section. in safe driving conditions following local laws and phone use.
Page 134: Operation
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Operation example, you can use the compound form voice Voice commands can be used to operate the Uconnect™ command “Phonebook New Entry”, or you can break Phone and to navigate through the Uconnect™ Phone the compound form command into two voice com- menu structure.
Page 135 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 • When prompted, after the beep, say “Pair a Device” Cancel Command At any prompt, after the beep, you can say “Cancel” and and follow the audible prompts. you will be returned to the main menu. However, in a •...
Page 136 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The Uconnect™ Phone will confirm the phone number phone to use if multiple mobile phones are in the vehicle at the same time. For example, if priority three and then dial. The number will appear in the display and priority five phones are present in the vehicle, the of certain radios.
Page 137 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 • The Uconnect™ system will confirm the name and • When prompted, enter the number designation (e.g., then dial the corresponding phone number, which “Home”, “Work”, “Mobile”, or “Other”). This will may appear in the display of certain radios. allow you to store multiple numbers for each phone- book entry, if desired.
Page 138 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Depending on the maximum number of entries down- Phonebook Download – Automatic Phonebook Transfer From Mobile Phone loaded, there may be a short delay before the latest If equipped and specifically supported by your phone, downloaded names can be used.
Page 139 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Edit Uconnect™ Phonebook Entries After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in NOTE: the phonebook, call the number you just edited, or return •...
Page 140 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After you enter the Phonebook Delete menu, you will Delete/Erase “All” Uconnect™ Phonebook Entries then be asked for the name of the entry that you wish • Press the button to begin. to delete.
Page 141: Phone Call Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 • After the “Ready” prompt and the following beep, say mobile service plan. For example, if your mobile service “Phonebook List Names”. plan provides three-way calling, this feature can be accessed through the Uconnect™ Phone. Check with •...
Page 142 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE mobile phone. Press the button to place the current Place/Retrieve A Call From Hold call on hold and answer the incoming call. To put a call on hold, press the button until you hear a single beep.
Page 143 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 • After the “Ready” prompt and the following beep, say Three-Way Calling To initiate three-way calling, press the button while “Redial”. a call is in progress, and make a second phone call, as •...
Page 144: Uconnect™ Phone Features
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ignition key is switched to OFF, a call can After selecting one of the languages, all prompts and continue on the Uconnect™ Phone for a certain dura- voice commands will be in that language. tion, after which the call is automatically transferred NOTE: After every Uconnect™...
Page 145 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 • After the “Ready” prompt and the following beep, say WARNING! “Emergency” and the Uconnect™ Phone will instruct the paired mobile phone to call the emergency num- To use your Uconnect™ Phone System in an emer- ber.
Page 146 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mexico City in Mexico). Please refer to the 24-Hour Working With Automated Systems “Towing Assistance” coverage details on the DVD in This method is used in instances where one generally has the Warranty Information Booklet and the 24-Hour to press numbers on the mobile phone keypad while Towing Assistance references.
Page 147 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 is also to be used for navigating through an automated Barge In — Overriding Prompts customer service center menu structure, and to leave a The “Voice Command” button can be used when you number on a pager.
Page 148 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phone And Network Status Indicators NOTE: Certain brands of mobile phones do not send the If available on the radio and/or on a premium display dial ring to the Uconnect™ Phone to play it on the vehicle such as the instrument panel cluster, and supported by audio system, so you will not hear it.
Page 149: Advanced Phone Connectivity
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Advanced Phone Connectivity List Paired Mobile Phone Names • Press the Transfer Call To And From Mobile Phone button to begin. The Uconnect™ Phone allows ongoing calls to be trans- • After the “Ready” prompt and the following beep, say ferred from your mobile phone to the Uconnect™...
Page 150: Things You Should Know About Your Uconnect™ Phone
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the “Ready” prompt and the following beep, say • You can also press the button at any time while the “Setup Select Phone” and follow the prompts. list is being played, and then choose the phone you wish to delete.
Page 151 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 • Press the button and say the “Voice Training, This will delete all phone pairing, phone book entries, System Training, or Start Voice Training” command. and other settings in all language modes. The System will prompt you before resetting to factory settings.
Page 152 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • low-to-medium vehicle speed, • Phonebook (Downloaded and Uconnect™ Phone Lo- cal) name recognition rate is optimized when the • low road noise, entries are not similar. • smooth road surface, • Numbers must be spoken in single digits. “800” must •...
Page 153 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 • low road noise, Recent Calls If your phone supports “Automatic Phonebook Down- • smooth road surface, load”, Uconnect™ Phone can list your Outgoing, Incom- • fully closed windows, ing and Missed Calls. •...
Page 154 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After reading a message, you can “Reply” or “Forward” List of Preset Messages: the message using Uconnect™ Phone. 1. Yes Send Messages: 2. No You can send messages using Uconnect™ Phone. To send a new message: 3.
Page 155 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 • After the “Ready” prompt and the following beep, say 13. I’ll be late “Setup, SMS Incoming Message Announcement,” you 14. Are you there yet? will then be given a choice to change it. 15.
Page 156 154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 157 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155...
Page 158 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 159 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) zero call cancel confirmation prompts three continue four delete five dial download seven edit eight emergency nine English star (*) erase all plus (+) Espanol pound (#) Francais add location...
Page 160 158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) language return to main menu return or main menu list names select phone select list phones send mobile set up phone settings or phone set up mute towing assistance mute off...
Page 161: General Information
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 General Information NOTE: Take care to speak into the Voice Interface This device complies with Part 15 of the FCC rules and System as calmly and normally as possible. The ability of RSS 210 of Industry Canada. Operation is subject to the the Voice Interface System to recognize user voice com- following conditions: mands may be negatively affected by rapid speaking or a...
Page 162: Commands
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you ever wish to interrupt the system while it lists The system will best recognize your speech if the win- options, press the Voice Command button, listen dows are closed, and the heater/air conditioning fan is for the beep, and say your command.
Page 163 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 3. Use the ON/OFF VOLUME rotary knob to adjust the Radio AM volume to a comfortable level while the Voice Command To switch to the AM band, say “AM” or “Radio AM”. In system is speaking.
Page 164 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • “Menu Radio” (to switch to the radio menu) Disc To switch to the disc mode, say “Disc”. In this mode, you • “Main Menu” (to switch to the main menu) may say the following commands: Satellite Radio •...
Page 165 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 • “Switch to system setup” − “Continue” (to continue recording) • “Change to setup” − “Delete” (to delete the recording) • “Play Memos” (to play previously recorded memos) • “Main menu setup” or —...
Page 166: Voice Training
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Training SEATS For users experiencing difficulty with the system recog- Seats are a part of the Occupant Restraint System of the nizing their voice commands or numbers the Uconnect™ vehicle. Voice “Voice Training” feature may be used. WARNING! 1.
Page 167: Power Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Power Seats — If Equipped Adjusting The Seat Forward Or Rearward Some models may be equipped with eight-way power The seat can be adjusted both forward and rearward. seats for the driver and front passenger. The power seat Push the seat switch forward or rearward, the seat will switches are located on the outboard side of the seat.
Page 168 166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining The Seatback WARNING! (Continued) The angle of the seatback can be adjusted forward or • Do not ride with the seatback reclined so that the rearward. Push the seatback switch forward or rearward, shoulder belt is no longer resting against your the seat will move in the direction of the switch.
Page 169: Power Lumbar - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Power Lumbar — If Equipped Heated Seats — If Equipped Vehicles equipped with power driver or passenger seats On some models, the front and rear seats may be may be also be equipped with power lumbar. The power equipped with heaters in both the seat cushions and lumbar switch is located on the outboard side of the seatbacks.
Page 170 168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Heated Seats WARNING! (Continued) There are two heated seat switches that allow the driver • Do not place anything on the seat that insulates and passenger to operate the seats independently. The against heat, such as a blanket or cushion.
Page 171 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 When the HIGH-level setting is selected, the heater will provide a boosted heat level during the initial stages of operation. Then, the heat output will drop to the normal HIGH-level. If the HIGH-level setting is selected, the system will automatically switch to LOW-level after a maximum of 60 minutes of continuous operation.
Page 172: Manual Front/Second Row Seat Adjuster
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the switch once to select HIGH-level Manual Front/Second Row Seat Adjuster heating. Press the switch a second time to select Both front seats are adjustable forward or rearward. The LOW-level heating. Press the switch a third manual seat adjustment handle is located under the seat time to shut the heating elements OFF.
Page 173: Manual Reclining Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 While sitting in the seat, pull up on the handle and slide Manual Reclining Seats — If Equipped the seat forward or rearward. Release the bar once you For models equipped with manual reclining seats, the have reached the desired position.
Page 174: Head Restraints
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To recline, lean forward slightly, lift the lever, then push WARNING! back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its The head restraints for all occupants must be prop- normal position.
Page 175 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 When AHRs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the AHR. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear impacts.
Page 176 174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For comfort the Active Head Restraints can be tilted forward and rearward. To tilt the head restraint closer to the back of your head, pull outward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head.
Page 177 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 • In the event of deployment of an Active Head Re- WARNING! (Continued) straint, refer to “Occupant Restraints/Resetting Active • Active Head Restraints may be deployed if they Head Restraints (AHR)” in “Things To Know Before are struck by an object such as a hand, foot or loose Starting Your Vehicle”...
Page 178: Stow 'N Go Seating - If Equipped
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Head Restraints — Second Row Quad Seats Head Restraints — Second Row Bench To raise the head restraint, pull upward on the head To raise the head restraint, pull upward on the head restraint.
Page 179 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 Second Row Stow ’n Go On vehicles equipped with Stow ’n Go seats, the seats will fold and tumble in one motion. 1. Move the front seat fully forward. 2. Recline the front seatback fully forward. 3.
Page 180 178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Pull upward on the seatback recliner lever located on The non-adjustable head restraint and seatback will fold the outboard side of the seat. automatically during the seat tumble. No additional actuation is necessary. Seatback Recliner Lever, Seat Tumble, And Head Restraint Fold Lever Non-Adjustable Head Restraint...
Page 181 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 The seat will automatically tumble into position for easy storage. Automatic Folding Seatback Tumbled Second Row Seat...
Page 182 180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. Push the seat into the storage bin. CAUTION! The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover. WARNING! In a collision, serious injury could result if the seat storage bin covers are not properly latched.
Page 183 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 To Unstow Second Row Seats 1. Return the seatback to the upright position. 1. Pull up on the storage bin latch to open the cover. 2. Pull up on the strap to lift the seat out of the storage bin and push the seat rearward to latch the seat anchors.
Page 184 182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Return the head restraint to the upright position. Easy Entry Second Row The second row Stow ’n Go seats allow easy entry to the third row seat or rear cargo area. Pull up on the seatback recliner lever on the outboard side of the seat.
Page 185: Quad Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 The seat will automatically fold into position for easy entry into the third row. WARNING! In the event of a collision you could be injured if the seat is not fully latched. Quad Seats — If Equipped Both Quad seats are adjustable forward or rearward.
Page 186 184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked.
Page 187 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 Fold-Flat Easy Entry To fold the seat, lift the recliner lever to the full upward The Quad seats can be tilted forward for easy entry into position and push the seatback forward until it rests on the third row.
Page 188 186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For passengers seated in the third row, there is a pull To provide additional space behind the second row seats, strap located on the outboard side of the seat near the the seats can be folded forward. bottom of the seat back.
Page 189 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Pull out the retainer strap from the sewn-in pocket Place the strap around the grab handle located on the located on the base of the seat cushion. B-Pillar. Before securing the strap, adjust the buckle for proper fit.
Page 190 188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Secure the retainer strap to the inside grab handle located WARNING! on the B-Pillar. When not in use, store the strap in the sewn-in pocket located on the base of the seat cushion. To reduce the risk of personal injury: •...
Page 191: Second Row Bench Seat - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 Removal Second Row Bench Seat — If Equipped The Quad seats can be removed if additional storage is While the bench seat does not stow in the floor, it is needed. With the seat in the easy entry position, lift the removable for added cargo space.
Page 192 190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Release levers are located on the rear leg assemblies, near To reinstall the seat, align the seat into the detent posi- the floor. To remove the seat, squeeze each release handle tions on the floor. Squeeze the release handle and rotate and rotate downwards to deploy the wheels.
Page 193: Third Row Power Recline - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 Third Row Power Recline — If Equipped Third Row Power Folding Seat — If Equipped The power recline feature, located on the side of the seat A one-touch power folding seat switch is located in the cushion, adjusts the seatback angle forward/rearward left rear trim panel as part of a switch bank.
Page 194 192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The switch is only functional when the liftgate is open Left and right third row seats can be folded individually and the vehicle is in PARK. or together. The third row power folding seat adjusts to the following positions using the switch bank located on the left rear trim panel: One Touch Folding Seat Third Row...
Page 195: Manually Folding Third Row Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 NOTE: 2. Lower the outboard head restraints by pulling on the • Disconnect the center shoulder belt from the small release strap marked “1” located on the outboard side of buckle and lower the head restraints before attempting the head restraint.
Page 196 194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull release strap marked “2” located on the rear of the 4. Pull release strap marked “3” to release the anchors. seat to lower the seatback. Release Strap “3” Release Strap “2”...
Page 197 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 5. Pull release strap marked “4” and tumble the seat rearward into the storage bin. Stowed Third Row Seat To Unfold Third Row Seats Release Strap “4” 1. Pull up on the assist strap to lift the seat out of the storage bin and push the seat forward until the anchors latch.
Page 198: Plastic Grocery Bag Retainer Hooks
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pulling strap “4” releases the seatback to return to its WARNING! full upright position. To avoid serious injury or death, never operate the 4. Raise the head restraint to its upright position. vehicle with occupants in the third row seat while in the tailgate mode.
Page 199: Setting Memory Positions And Linking Rke
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 Setting Memory Positions And Linking RKE Transmitter To Memory NOTE: Each time the SET (S) button and a numbered button (1 or 2) is pressed, you erase the memory settings for that button and store a new one. 1.
Page 200 198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Turn on the radio and set the radio station presets (up 11. Select “Remote Linked to Memory” in the Electronic to 10 AM and 10 FM stations can be set). Vehicle Information Center (EVIC) and enter “Yes”. Refer to “Electronic Vehicle Information Center (EVIC)/ 6.
Page 201 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 To recall the memory setting for driver two, press 3. Press and release the memory SET (S) button located MEMORY button 2 on the driver’s door or the UNLOCK on the driver’s door. A chime will sound signaling that button on the RKE transmitter linked to Memory Position you are in the memory set mode.
Page 202: Easy Entry/Exit Seat (Available With Memory Seat Only)
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Easy Entry/Exit Seat between 0.9 – 2.7 in (22.7 – 67.7 mm) forward of the (Available With Memory Seat ONLY) rear stop. The seat will return to its previously set This feature provides automatic driver seat positioning to position when you insert the key into the ignition enhance driver mobility when entering and exiting the switch and turn it out of the LOCK position.
Page 203: To Open And Close The Hood
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 Customer-Programmable Features” in “Understanding 2. Move to the front of the vehicle and look inside the Your Instrument Panel” for further information. center of the hood opening. Locate, then push the safety catch lever downward while raising the hood at the same TO OPEN AND CLOSE THE HOOD time.
Page 204: Lights
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Use the hood prop rod to secure the hood in the open LIGHTS position. All of the lights, except the Hazard Warning lights, headlight high beams and flash-to-pass, are controlled by CAUTION! switches to the left of the steering column on the instru- ment panel.
Page 205: Interior Lighting
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 Interior Lighting Interior lights are turned on when a door or liftgate is opened, the Remote Keyless Entry (RKE) transmitter is activated, or when the dimmer control is moved to the extreme top. The interior lights will automatically turn off in approxi- mately 10 minutes for the first activation and 90 seconds every activation thereafter until the engine is started, if...
Page 206 204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dimmer Control Halo Lights — If Equipped With the parking lights or headlights on, rotating the left Halo lights are strategically placed soft lighting that help dimmer control for the interior lights on the instrument to illuminate specific areas to aid the occupants in panel upward will increase the brightness of the instru- locating specific features while driving at night.
Page 207: Parking Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 To activate the Halo lights, rotate the Halo the headlight switch to the extreme counterclockwise switch control upward or downward to in- position aligning the indicator with AUTO on the head- crease or decrease the lighting. light switch.
Page 208: Headlight Delay - If Equipped
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlight Delay — If Equipped If the headlights are turned off before the ignition, they This feature provides the safety of headlight illumination will turn off in the normal manner. for up to 90 seconds after exiting your vehicle. NOTE: The headlights must be turned off within 45 sec- To activate the delay feature, turn OFF the ignition switch onds of turning the ignition OFF to activate this feature.
Page 209: Front Fog Lights - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 the turn signal activation. Once the turn signal is no The battery protection feature will be disabled if the longer active, the DRL lamp will illuminate. ignition switch is turned to any other position other than LOCK during the eight minute delay.
Page 210: Turn Signals
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The multifunction lever controls the: Lane Change Assist Tap the lever up or down once, without moving beyond • Turn Signals the detent, and the turn signal (right or left) will flash • Headlight Beams Low/High three times then automatically turn off.
Page 211: Flash-To-Pass
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 Flash-To-Pass 2. Rotate the headlight switch counterclockwise to the You can signal another vehicle with your headlights by AUTO (A) position. lightly pulling the multifunction lever toward you. This 3. Push the multifunction lever away from you to switch will turn on the high beam headlights until the lever is the headlights to the high beam position.
Page 212: Windshield Wipers And Washers
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Rotate the headlight switch clockwise from the AUTO (A) to the on position. NOTE: Broken, muddy or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film and other obstructions on the windshield or camera lens will cause the system to function improperly.
Page 213: Mist, Front Wiper And Washer
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 Mist, Front Wiper And Washer Use one of the five intermittent wiper settings when Use the Mist feature when weather conditions make weather conditions make a single wiping cycle, with a occasional usage of the wipers necessary. variable delay between cycles, desirable.
Page 214: Rain Sensing Wipers - If Equipped
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The sensitivity of the system is adjustable from the WARNING! multifunction lever. Wiper sensitivity position 3 has been calibrated for best overall wiping sensitivity. If the opera- Sudden loss of visibility through the windshield tor desires more wiping sensitivity, they may select could lead to a collision.
Page 215 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 • The Rain Sensing feature can be turned on and off • Neutral Wipe Inhibit — The Rain Sensing feature will through the EVIC (if equipped). Refer to “Electronic not operate when the ignition is ON, and the trans- Vehicle Information Center (EVIC)/Personal Settings mission shift lever is in the NEUTRAL position, and (Customer-Programmable Features)”...
Page 216 214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT/TELESCOPING STEERING COLUMN To unlock the steering column, push the lever downward This feature allows you to tilt the steering column (toward the floor). To tilt the steering column, move the upward or downward. It also allows you to lengthen or steering wheel upward or downward as desired.
Page 217: Heated Steering Wheel - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 HEATED STEERING WHEEL — IF EQUIPPED NOTE: The engine must be running for the heated The steering wheel contains a heating element that helps steering wheel to operate. warm your hands in cold weather. The heated steering Vehicles Equipped With Remote Start wheel has only one temperature setting.
Page 218: Adjustable Pedals - If Equipped
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material. This may cause the steering wheel heater to overheat. ADJUSTABLE PEDALS —...
Page 219: Electronic Speed Control - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 • The pedals cannot be adjusted when the vehicle is in WARNING! REVERSE or when the Electronic Speed Control Sys- tem is on. The following messages will be displayed Do not adjust the pedals while the vehicle is moving. on vehicles equipped with the Electronic Vehicle In- You could lose control and have an accident.
Page 220: To Activate
218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Electronic Speed Control buttons are located on the down if multiple Speed Control functions are operated at right side of the steering wheel. the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed.
Page 221: To Set A Desired Speed
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 To Set A Desired Speed To Vary The Speed Setting Turn the Electronic Speed Control ON. When the vehicle When the Electronic Speed Control is set, you can in- has reached the desired speed, press the SET (-) button crease speed by pushing the RES (+) button.
Page 222: To Accelerate For Passing
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing WARNING! Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Electronic Speed Control can be dangerous where the system cannot maintain a constant speed.
Page 223: Parksense Sensors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 ParkSense will retain the last system state (enabled or ParkSense Sensors disabled) from the last ignition cycle when the ignition is The four ParkSense sensors, located in the rear fascia/ changed to the ON/RUN position. bumper, monitor the area behind the vehicle that is within the sensors’...
Page 224: Parksense Display
222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The ParkSense Warning Display is located in the Instru- ParkSense Display ment cluster’s EVIC display. It provides both visual and When the vehicle is in REVERSE, the warning display audible warnings to indicate the distance between the will turn ON indicating the system status.
Page 225 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 The system will indicate a detected obstacle by showing three solid arcs and will produce a one-half second tone. As the vehicle moves closer to the object the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.
Page 226 224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fast Tone Continuous Tone The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle:...
Page 227: Enabling/Disabling Parksense
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 WARNING ALERTS Rear Distance Greater than 79-39 in 39-25 in 25-12 in Less than (in/cm) 79 in (200 cm) (200-100 cm) (100-65 cm) (65-30 cm) 12 in (30 cm) Audible Alert None Single 1/2 Slow Fast Continuous...
Page 228: Service The Parksense Rear Park Assist System
226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE shift lever is moved to REVERSE and the system is If “CLEAN PARK ASSIST SENSORS” appears in the disabled, the EVIC will display the “PARK ASSIST SYS- EVIC after making sure the rear fascia/bumper is free TEM OFF”...
Page 229 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 • Jackhammers, large trucks, and other vibrations could properly. The ParkSense system might not detect an affect the performance of ParkSense . obstacle behind the fascia/bumper, or it could provide a false indication that an obstacle is behind the fascia/ •...
Page 230 228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! • ParkSense is only a parking aid and it is unable • Drivers must be careful when backing up even to recognize every obstacle, including small ob- when using the ParkSense Rear Park Assist Sys- stacles.
Page 231: Parkview Rear Back Up Camera - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229 PARKVIEW REAR BACK UP CAMERA — IF WARNING! (Continued) EQUIPPED • Before using the ParkSense Rear Park Assist Your vehicle may be equipped with the ParkView Rear System, it is strongly recommended that the ball Back Up Camera that allows you to see an on-screen mount and hitch ball assembly is disconnected image of the rear surroundings of your vehicle whenever...
Page 232 230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When displayed, static grid lines will illustrate the width that will help indicate the distance to the rear of the of the vehicle while a dashed center-line will indicate the vehicle. The following table shows the approximate center of the vehicle to assist with aligning to a hitch/ distances for each zone: receiver.
Page 233: Turning Parkview On Or Off - With Navigation/Multimedia Radio
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 WARNING! CAUTION! (Continued) • To avoid vehicle damage, the vehicle must be Drivers must be careful when backing up even when driven slowly when using ParkView to be able to using the ParkView Rear Back Up Camera. Always stop in time when an obstacle is seen.
Page 234: Turning Parkview On Or Off - Without Navigation/Multimedia Radio
232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Enable or disable the rear camera feature by selecting illuminates the instrument panel cupholders, two swiv- “enable rear camera in reverse” soft-key. eling LED lights, flip-down sunglass storage, conversa- tion mirror, optional power sliding door switches and an 5.
Page 235: Courtesy/Interior Lighting
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 Courtesy/Interior Lighting Sunglass Storage (Non-Sunroof Only) At the forward end of the console are two courtesy lights At the front of the overhead console, a compartment is (standard dome light has two buttons). The lights turn on provided for the storage of two pairs of sunglasses.
Page 236 234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The door will slowly rotate to the full open position. Conversation Mirror Position NOTE: From the “conversation mirror” position, the Full Open Position door can only be closed. From this position, the door can be fully closed or, by rotating upward about 3/4 of the way and releasing, To return to the full open position, the door must first be positioned for conversation mirror use.
Page 237: Rear Courtesy/Reading Lights - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235 Rear Courtesy/Reading Lights — If Equipped The overhead console has two sets of courtesy lights. The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry (RKE) the lights will also turn on when the UNLOCK button on the RKE transmitter is pressed.
Page 238: Garage Door Opener - If Equipped
236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE An additional LED at the front of the rear console shines Rear Console Halo Lighting down on the front foot-well area while in courtesy mode, The rear overhead console has recessed halo lighting for added convenience.
Page 239 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237 HomeLink Buttons/Sunvisor/Headliner HomeLink Buttons/Overhead Consoles NOTE: HomeLink is disabled when the Vehicle Secu- rity Alarm is active.
Page 240: Before You Begin Programming Homelink
238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Before You Begin Programming HomeLink NOTE: • Erasing all channels should only be performed when Be sure that your vehicle is parked outside of the garage before you begin programming. programming HomeLink for the first time. Do not erase channels when programming additional buttons.
Page 241 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 239 3. Simultaneously press and hold both the Homelink button you want to program and the hand-held transmit- ter button. 4. Continue to hold both buttons and observe the indi- cator light. The Homelink indicator will flash slowly and then rapidly after Homelink has received the fre- quency signal from the hand-held transmitter.
Page 242: Programming A Non-Rolling Code
240 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: You have 30 seconds in which to initiate the next 2. Press and hold the desired HomeLink button until step after the LEARN button has been pressed. the indicator light begins to flash after 20 seconds. Do not release the button.
Page 243: Canadian/Gate Operator Programming
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 241 4. Continue to hold both buttons and observe the indi- Reprogramming A Single HomeLink Button cator light. The Homelink indicator will flash slowly To reprogram a channel that has been previously trained, and then rapidly after Homelink has received the fre- follow these steps: quency signal from the hand-held transmitter.
Page 244 242 UNDERSTANDING THE FEATURES OF YOUR VEHICLE to pick up the signal during programming. Similar to this 4. Watch for the HomeLink indicator to change flash Canadian law, some U.S. gate operators are designed to rates. When it changes, it is programmed. It may take up time-out in the same manner.
Page 245: Using Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 243 Reprogramming A Single HomeLink Button Security To reprogram a channel that has been previously trained, It is advised to erase all channels before you sell or turn follow these steps: in your vehicle. 1.
Page 246: Troubleshooting Tips
244 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Troubleshooting Tips WARNING! If you are having trouble programming HomeLink , here • Your motorized door or gate will open and close are some of the most common solutions: while you are programming the universal trans- •...
Page 247: General Information
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 245 General Information POWER SUNROOF — IF EQUIPPED This device complies with FCC rules Part 15 and Industry The power sunroof switch is located between the sun Canada RSS-210. Operation is subject to the following visors on the overhead console.
Page 248: Opening Sunroof - Express
246 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof — Express WARNING! Press the switch rearward and release it within one-half • Never leave children in a vehicle with the key in second and the sunroof will open automatically from any position.
Page 249: Closing Sunroof - Manual Mode
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 247 automatically. This is called “Express Close”. During Pinch Protect Override Express Close operation, any movement of the sunroof If a known obstruction (ice, debris, etc.) prevents closing switch will stop the sunroof. the sunroof, press the switch forward and hold for two seconds after the reversal occurs.
Page 250: Wind Buffeting
248 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The sunshade cannot be closed if the sunroof is Ignition Off Operation open. For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power sunroof switch Wind Buffeting will remain active for 45 seconds after the ignition switch Wind buffeting can be described as the perception of is turned to the LOCK position.
Page 251 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 249 switch and the passenger-side power outlet is connected NOTE: To ensure proper operation a MOPAR cigar directly to the battery. The driver-side power outlet will knob and element must be used. also operate a conventional cigar lighter unit (if equipped CAUTION! with an optional Smoker’s Package).
Page 252 250 UNDERSTANDING THE FEATURES OF YOUR VEHICLE One outlet in the removable floor console (if equipped) On vehicles equipped with the Super Console the power shares a fuse with the lower outlet in the instrument outlets are located under the retractable cover. To access panel and is also connected to the battery.
Page 253 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 251 The outlet in the rear quarter panel near the liftgate and the upper outlet in the instrument panel are both con- trolled by the ignition switch. Each of these outlets can support 160 Watts (13 Amps). Do not exceed 160 Watts (13 Amps) for each of these outlets.
Page 254 252 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Many accessories that can be plugged in draw To avoid serious injury or death: • Only devices designed for use in this type of power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
Page 255: Power Inverter - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 253 CAUTION! (Continued) • Power outlets are designed for accessory plugs only. Do not hang any type of accessory or acces- sory bracket from the plug. Improper use of the power outlet can cause damage. POWER INVERTER —...
Page 256: Cupholders
254 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This outlet can power cellular phones, electronics and CUPHOLDERS other low power devices requiring power up to 150 There are cupholders located throughout the interior. All Watts. Certain high-end video games, such as Playsta- liners are removable for cleaning.
Page 257: Super Console - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 255 Super Console — If Equipped On models equipped with the Super Console, there are two cupholders located in the center of the console. Front Cupholders Pull the drawer out firmly until it stops, and place the container to be held in either one of the cupholder wells.
Page 258: Premium Console Cupholders - If Equipped
256 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For rear passengers two cupholders are located in the Premium Console Cupholders — If Equipped pull-out drawer, located in the back of the Super Console. On models equipped with premium center consoles, Pull the drawer out to the first position to use the there are four cupholders located on the top of the cupholders.
Page 259: Interior Bottle Holders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257 Interior Bottle Holders There are four bottle holders located in the interior. One bottle holder is molded into each front interior door trim panels, and one bottle holder is molded into each side sliding interior door trim panel.
Page 260: Smoker's Package Kit - If Equipped
258 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Smoker’s Package Kit — If Equipped Upper Glove Compartment With the optional authorized dealer-installed Smoker’s To open the upper compartment, press in on the button, Package Kit, a removable ash receiver is inserted into one located on the left side of the upper door.
Page 261: Door Trim Panel Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 259 Lower Glove Compartment Door Trim Panel Storage To open the lower compartment pull out on the release Front Door Storage handle. Both interior front door panels have multiple pockets for storage. WARNING! If containers of hot liquid are placed in the bottle holder, they can spill when the door is closed, burn- ing the occupants.
Page 262: Driver Seatback Storage - If Equipped
260 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driver Seatback Storage — If Equipped Umbrella Holder The drivers seatback has a primary storage pocket on all An umbrella holder has been conveniently molded into models and an optional secondary mesh pocket. the left front door entry scuff molding.
Page 263: Second Row Floor Storage Bins
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 261 Second Row Floor Storage Bins CAUTION! The area below the floor covers, located in front of the second row seats, is available for storage. The storage bin cover must lay flat and be locked to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.
Page 264: Storage Bin Safety Warning
262 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage Bin Safety Warning WARNING! (Continued) Carefully follow these warnings to help prevent personal • Do not operate the storage bin covers while the injury or damage to your vehicle: vehicle is in motion. •...
Page 265: Center And Rear Overhead Console Storage - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 263 Center And Rear Overhead Console Storage — If Equipped The overhead storage system comes in several options. Storage Bin Cover Emergency Release Lever NOTE: In the event of an individual being locked inside the storage bin, the storage bin cover can be opened from Overhead Console Features inside of the bin by pushing on the glow-in-the-dark...
Page 266: Coat Hooks
264 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Coat Hooks Coat hooks are located along the headliner for the second and third row seating positions. The coat hook load limit is 10 lbs (4.5 kg). Exceeding the recommended load limit can cause the coat hooks to break or disengage from the vehicle.
Page 267: Console Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 265 • Four cupholders accept up to extra large size beverage CONSOLE FEATURES There are three consoles available: Basic, Premium and cups or 20 oz (.6 L) plastic bottles. Cupholders are Super. dishwasher safe for cleaning. •...
Page 268: Premium Console - If Equipped
266 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Reinstall The Basic Floor Console WARNING! 1. Position the console at a slight angle (front slightly In an accident, serious injury could result if the higher than the rear). removable floor console is not properly installed. 2.
Page 269 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 267 • Large console center storage will store headphones for Position 1 shows the console closed with four cupholders the available rear DVD entertainment system or other and a convenient storage tray. items • 12 Volt DC power outlet provides continuous power inside the console for cell phones or other electronics.
Page 270 268 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Position 2 shows the raised storage tray revealing a large Dual Storage Bins storage area below. Position 3 shows the top portion of the console in a rearward position. This is accomplished by lifting the upper most latch at the front of the console.
Page 271 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 269 Position 4 shows the complete console in its rearmost To Remove The Premium Floor Console position. Again, lifting second latch handle at the front of 1. Pull up on the bottom release handle in the front of the the console, allows complete access to a lower storage bin console.
Page 272: Super Console - If Equipped
270 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Pull up on the console to be sure it is firmly latched. WARNING! In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched.
Page 273 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 271 NOTE: The front cupholder light ring and pass through lighting is controlled by a dimming switch located on the instrument panel, refer to “Lights” in “Understanding The Features Of Your Vehicle” for further information. Located in the back of the super console is a storage drawer and cupholders for the rear passengers.
Page 274: Cargo Area Features
272 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO AREA FEATURES Rechargeable Flashlight The rechargeable flashlight is mounted on the right side of the cargo area. The flashlight snaps out of the bezel when needed. The flashlight features two bright LED light bulbs and is powered by a lithium battery that recharges when snapped back into place and the vehicle is either running or the key is in the accessory position.
Page 275: Rear Window Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 273 To operate the flashlight, press the switch once for high, REAR WINDOW FEATURES twice for low, and a third time to return to off. Rear Window Defroster The rear window defroster button is located on the climate control (Mode) knob.
Page 276: Rear Load-Leveling System - If Equipped
274 UNDERSTANDING THE FEATURES OF YOUR VEHICLE A hydraulic pump contained within the shock absorbers CAUTION! raises the rear of the vehicle to the correct height. It takes approximately 1 mile (1.6 km) of driving for the leveling Failure to follow these cautions can cause damage to to complete depending on road surface conditions.
Page 277 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 275 The crossbars and side rails are designed to carry weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. NOTE: •...
Page 278: Deploying The Crossbars
276 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Deploying the Crossbars CAUTION! To deploy the crossbars, completely loosen the thumb screws at both ends of the crossbar and lift the crossbar Use care when removing and handling the crossbars from its stowed position in the side rail. Repeat with to prevent damage to the vehicle.
Page 279 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 277 Stowed Position Deployed Position Then, position the crossbars across the roof.
Page 280 278 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The crossbars are identical and can be placed in any two of the three deploy positions. Crossbar To Side Rail Installation Once the crossbars are set into position, tighten the thumb screws completely. Deploy Positions –...
Page 281 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 279 NOTE: Load should always be secured to crossbars first, with rail tie down loops used as additional securing points if needed. Tie loops are intended as supplemen- tary tie down points only. Do not use ratcheting mecha- nisms with the tie loops.
Page 282 280 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! CAUTION! (Continued) • Long loads which extend over the windshield, • Check deployed crossbars frequently and re- such as wood panels or surfboards, or loads with tighten thumb screws as necessary. large frontal area should be secured to both the •...
Page 283: Sun Screens - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 281 WARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in per- sonal injury or property damage. Follow the Roof Rack Cautions when carrying cargo on your roof rack.
Page 284 282 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Once the screen is completely to the top of the window, To lower the sun screen, gently lift the tab upward to extend the top bar of the sun screen over the two hooks disengage the hooks, and feed the screen back into the attached to the top of the window.
Page 285: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS ▫ EVIC Red Telltale Lights ....310 Instrument Panel Features ....287 ▫...
Page 286 284 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Messages # ......318 ▫ Operation Instructions — CD Mode For CD And MP3 Audio Play .
Page 287 UNDERSTANDING YOUR INSTRUMENT PANEL 285 ▫ Operating Instructions (Uconnect™ Phone) ▫ Play Video Games ....360 — If Equipped ..... . 352 ▫...
Page 288 286 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Locking The Remote Control ... . 378 Climate Controls ..... . 398 ▫...
Page 289: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 287 INSTRUMENT PANEL FEATURES 1 — Air Vents 5 — Analog Clock 9 — DVD – If Equipped 13 — Ignition Switch 2 — Instrument Cluster 6 — Upper Glove Compartment 10 — Storage Bin 14 — Hood Release 3 —...
Page 290: Instrument Cluster - Base
288 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — BASE...
Page 291: Instrument Cluster - Premium
UNDERSTANDING YOUR INSTRUMENT PANEL 289 INSTRUMENT CLUSTER — PREMIUM...
Page 292: Instrument Cluster Descriptions
290 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 4. Turn Signal Indicators The arrow will flash with the exterior turn signal 1. Tachometer when the turn signal lever is operated. The red segments indicate the maximum permissible engine revolutions per minute (RPM x 1000) for each gear If the vehicle is driven more than 1 mile (1.6 km) with range.
Page 293 UNDERSTANDING YOUR INSTRUMENT PANEL 291 U.S. Federal regulations require that upon transfer of Message Display Area vehicle ownership, the seller certify to the purchaser the When the appropriate conditions exist, the following correct mileage that the vehicle has been driven. If your odometer messages will display: odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same...
Page 294 292 UNDERSTANDING YOUR INSTRUMENT PANEL LoW tirE CHAngE OIL When the appropriate condition exists, the odometer Your vehicle is equipped with an engine oil change display will toggle between LoW and tirE for three cycles. indicator system. The CHAngE OIL message will flash in the instrument cluster odometer for approximately gASCAP 12 seconds, after a single chime has sounded, to indicate...
Page 295 UNDERSTANDING YOUR INSTRUMENT PANEL 293 2. Fully depress the accelerator pedal, slowly, three times If the ABS light remains on or turns on while driving, it within 10 seconds. indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. However, 3.
Page 296 294 UNDERSTANDING YOUR INSTRUMENT PANEL vehicle placard or tire inflation pressure label, you should Your vehicle has also been equipped with a TPMS determine the proper tire inflation pressure for those tires.) malfunction indicator to indicate when the system is not operating properly.
Page 297 UNDERSTANDING YOUR INSTRUMENT PANEL 295 does not come on when turning the key from OFF to CAUTION! ON/RUN, have the condition checked promptly. The TPMS has been optimized for the original Certain conditions, such as a loose or missing gas cap, equipment tires and wheels.
Page 298 296 UNDERSTANDING YOUR INSTRUMENT PANEL system. If this light remains on after several ignition WARNING! cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see A malfunctioning catalytic converter, as referenced your authorized dealer as soon as possible to have the above, can reach higher temperatures than in normal problem diagnosed and corrected.
Page 299 UNDERSTANDING YOUR INSTRUMENT PANEL 297 11. Electronic Stability Control (ESC) OFF Indicator 15. Air Bag Warning Light Light — If Equipped This light will turn on for four to eight seconds This light indicates the Electronic Stability Con- as a bulb check when the ignition switch is first trol (ESC) is off.
Page 300 298 UNDERSTANDING YOUR INSTRUMENT PANEL Select (ERS) feature is active. Use the +/- selector on If the light remains on when the parking brake has been the shift lever to activate ERS. Refer to “Automatic disengaged, and the fluid level is at the full mark on the Transmission”...
Page 301 UNDERSTANDING YOUR INSTRUMENT PANEL 299 NOTE: The light may flash momentarily during sharp Operation of the Brake Warning Light can be checked by cornering maneuvers, which change fluid level condi- turning the ignition switch from the OFF position to the tions.
Page 302 300 UNDERSTANDING YOUR INSTRUMENT PANEL 19. Seat Belt Reminder Light The gauge pointer will likely indicate a higher tempera- When the ignition switch is first turned to ON/ ture when driving in hot weather, up mountain grades, RUN, this light will turn on for four to eight or when towing a trailer.
Page 303 UNDERSTANDING YOUR INSTRUMENT PANEL 301 while driving, turn off some of the vehicle’s non-essential WARNING! electrical devices or increase engine speed (if at idle). If the charging system light remains on, it means that the A hot engine cooling system is dangerous. You or vehicle is experiencing a problem with the charging others could be badly burned by steam or boiling system.
Page 304 302 UNDERSTANDING YOUR INSTRUMENT PANEL 24. Engine Temperature Warning Light 25. Electronic Throttle Control (ETC) Light This light warns of an overheated engine condi- This light informs you of a problem with the tion. As engine coolant temperatures rise and the Electronic Throttle Control (ETC) system.
Page 305 UNDERSTANDING YOUR INSTRUMENT PANEL 303 26. Transmission Temperature Warning Light CAUTION! During sustained high speed driving or trailer towing up long grades on hot days, the auto- Continuous driving with the Transmission Tempera- matic transmission oil may become too hot. ture Warning Light illuminated will eventually cause When the transmission overheat warning light severe transmission damage or transmission failure.
Page 306: Electronic Vehicle Information Center (Evic) - If Equipped
304 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER This system conveniently allows the driver to select a (EVIC) — IF EQUIPPED variety of useful information by pressing the switches The Electronic Vehicle Information Center (EVIC) fea- mounted on the steering wheel. The EVIC consists of the tures a driver-interactive display that is located in the following: instrument cluster.
Page 307 UNDERSTANDING YOUR INSTRUMENT PANEL 305 The system allows the driver to select information by UP Button pressing the following buttons mounted on the steering Press and release the UP button to scroll up- wheel: ward through the main menus (Fuel Economy, Vehicle Info, Tire PSI, Cruise, Messages, Units, System Setup) and sub-menus.
Page 308: Electronic Vehicle Information Center (Evic) Displays
306 UNDERSTANDING YOUR INSTRUMENT PANEL BACK Button messages that consist of approximately 60 possible warn- Press the BACK button to scroll back to a ing or information messages. These pop up messages fall previous menu or sub-menu. into several categories: •...
Page 309 UNDERSTANDING YOUR INSTRUMENT PANEL 307 • Unstored Messages Until RUN When the appropriate conditions exist, the EVIC displays These messages deal primarily with the Remote Start the following messages: feature. This message type is displayed until the ignition • Key in ignition is in the RUN state.
Page 310 308 UNDERSTANDING YOUR INSTRUMENT PANEL • Key not programmed • Service Keyless System • Vehicle Not in Park • LOW WASHER FLUID • Key Left Vehicle • Oil Change Required • Key Not Detected • Check Gascap • Press Brake Pedal and Push Button to Start •...
Page 311: Evic White Telltale Lights
UNDERSTANDING YOUR INSTRUMENT PANEL 309 • Blind Spot System Not Available — This message is EVIC White Telltale Lights displayed to indicate the Blind Spot Monitor (BSM) This area will show reconfigurable white caution tell- system is temporarily unavailable due to sensor block- tales.
Page 312: Evic Amber Telltale Lights
310 UNDERSTANDING YOUR INSTRUMENT PANEL • Electronic Speed Control SET to turn off the message. If the problem continues, the This light will turn on when the electronic message will appear the next time the vehicle is started. speed control is SET. For further information, A loose, improperly installed, or damaged fuel filler cap refer to “Electronic Speed Control”...
Page 313 UNDERSTANDING YOUR INSTRUMENT PANEL 311 • Oil Pressure Warning Light vehicle is experiencing a problem with the charging This light indicates low engine oil pressure. The system. Obtain SERVICE IMMEDIATELY. See an autho- light should turn on momentarily when the engine rized dealer.
Page 314 312 UNDERSTANDING YOUR INSTRUMENT PANEL If the light remains lit with the engine running, your shift the transmission into NEUTRAL and idle the ve- vehicle will usually be drivable. However, see an autho- hicle. If the temperature reading does not return to rized dealer for service as soon as possible.
Page 315: Oil Change Required
UNDERSTANDING YOUR INSTRUMENT PANEL 313 Unless reset, this message will continue to display each WARNING! time you turn the ignition switch to the ON/RUN position or cycle the ignition to the ON/RUN position if If the Transmission Temperature Warning Light is equipped with Keyless Enter-N-Go.
Page 316: Fuel Economy
314 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicles Not Equipped With Keyless Enter-N-Go Fuel Economy Press and release the UP or DOWN button until “Fuel 1. Turn the ignition switch to the ON/RUN position (Do Economy” displays highlighted in the EVIC and press not start the engine.) the SELECT button.
Page 317 UNDERSTANDING YOUR INSTRUMENT PANEL 315 NOTE: Significant changes in driving style or vehicle loading will greatly affect the actual drivable distance of the vehicle, regardless of the DTE displayed value. When the DTE value is less than 30 miles (48 km) estimated driving distance, the DTE display will change to a “LOW FUEL”...
Page 318: Vehicle Speed
316 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicle Speed Trip Info Press and release the UP or DOWN button until “Vehicle Press and release the UP or DOWN button until “Trip Speed” displays highlighted in the EVIC and press the Info” is highlighted in the EVIC and press the SELECT SELECT button.
Page 319: Tire Psi
UNDERSTANDING YOUR INSTRUMENT PANEL 317 To Reset A Trip Function press and release the SELECT button until a check-mark Reset will only occur while a resettable function is appears next to the setting, showing that the setting has selected (highlighted). Press and hold the SELECT button been selected.
Page 320: Understanding Your Instrument Panel Messages
318 UNDERSTANDING YOUR INSTRUMENT PANEL Messages # Compass / Temperature Display Select from Main Menu using the UP or DOWN buttons. The compass readings indicate the direction the vehicle is This feature shows the number of stored warning mes- facing. The EVIC will display one of eight compass sages (in the # place holder).
Page 321 UNDERSTANDING YOUR INSTRUMENT PANEL 319 metallic objects) until the CAL indicator displayed in the 4. Press and release the SELECT button to start the EVIC turns off. The compass will now function normally. calibration. The “CAL” indicator will be displayed in the EVIC.
Page 322: Customer-Programmable Features (System Setup)
320 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Keep magnetic materials away from the top of 2. Press the UP or DOWN button until the Setup the instrument panel, such as iPod’s, Mobile Phones, (Customer-Programmable Features) menu is reached, Laptops and Radar Detectors. This is where the compass then press the SELECT button.
Page 323 UNDERSTANDING YOUR INSTRUMENT PANEL 321 Press and release the UP or DOWN button until System route, mile by mile, turn-by-turn until the final destina- Setup is highlighted in the main menu of the EVIC. Then tion is reached. To make your selection, press and release press the SELECT button to enter the System Setup the SELECT button until a check-mark appears next to sub-menu.
Page 324 322 UNDERSTANDING YOUR INSTRUMENT PANEL Auto Unlock Doors appears next to the feature showing the system has been When ON is selected, all doors will unlock when the activated or the check-mark is removed showing the vehicle is stopped and the transmission is in the PARK or system has been deactivated.
Page 325 UNDERSTANDING YOUR INSTRUMENT PANEL 323 In warm weather, the driver vented seat feature will Horn with Remote Start automatically turn on when the remote start is activated. When this feature is selected, a short horn sound will These features will stay on through the duration of occur when the RKE transmitter REMOTE START button remote start or until the key is turned to RUN.
Page 326 324 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic High Beams — If Equipped Headlamps with Wipers When this feature is selected, the high beam headlights (Available with Auto Headlights Only) will deactivate automatically under certain conditions. To When ON is selected, and the headlight switch is in the make your selection, press and release the SELECT AUTO position, the headlights will turn on approxi- button until a check-mark appears next to the feature...
Page 327 UNDERSTANDING YOUR INSTRUMENT PANEL 325 the SELECT button until a check-mark appears next to Illuminated Approach the feature showing the system has been activated or the When this feature is selected, the headlights will activate check-mark is removed showing the system has been and remain on for up to 90 seconds when the doors are deactivated.
Page 328 326 UNDERSTANDING YOUR INSTRUMENT PANEL Keyless Enter-N-Go (Passive Entry) NOTE: The seat will return to the memorized seat This feature allows you to lock and unlock the vehicle’s location (if Recall Memory with Remote Key Unlock is set door(s) without having to press the RKE transmitter lock to ON) when the RKE transmitter is used to unlock the or unlock buttons.
Page 329: Media Center 730N/430/430N
UNDERSTANDING YOUR INSTRUMENT PANEL 327 Alert feature can be activated in “Blind Spot Alert Lights” Take your vehicle to an authorized dealer to verify sensor mode, when this mode is selected the Blind Spot Monitor alignment. Having a sensor that is misaligned will result (BSM) system is activated and will only show a visual in the BSM not operating to specification.
Page 330: Equipped
328 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions (Voice Command System) — If Equipped Refer to “Voice Command” in the Uconnect™ User Manual located on the DVD for further details. Operating Instructions (Uconnect™ Phone) — If Equipped Refer to “Uconnect™ Phone” in the Uconnect™ User Manual located on the DVD for further details.
Page 331 UNDERSTANDING YOUR INSTRUMENT PANEL 329 Power Switch/Volume Control (Rotary) TIME Button Push the ON/VOLUME control knob to turn on the Press the TIME button to alternate display of the time radio. Push the ON/VOLUME control knob a second and radio frequency. time to turn off the radio.
Page 332 330 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Push the rotary TUNE/SCROLL control knob a third Pressing the RW (Rewind) or FF (Fast Forward) buttons time and TREBLE will display. Turn the TUNE/SCROLL causes the tuner to search for the next frequency in the control knob to the right or left to increase or decrease the direction of the arrows.
Page 333: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
UNDERSTANDING YOUR INSTRUMENT PANEL 331 SET/RND Button — To Set the Pushbutton Every time a preset button is used, a corresponding Memory button number will display. When you are receiving a station that you wish to Buttons 1 - 6 commit to pushbutton memory, press the SET/RND These buttons tune the radio to the stations that you button.
Page 334 332 UNDERSTANDING YOUR INSTRUMENT PANEL • This radio is capable of playing compact discs (CD), CAUTION! recordable compact discs (CD-R), rewritable compact • This CD player will accept 4-3/4 in (12 cm) discs discs (CD-RW), compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks.
Page 335: Notes On Playing Mp3 Files
UNDERSTANDING YOUR INSTRUMENT PANEL 333 NOTE: Ejecting with the ignition OFF is not allowed on AM/FM Button convertible or soft-top models (if equipped). Press the button to select either AM or FM mode. SEEK Button SET/RND Button (Random Play Button) Press the right SEEK button for the next selection on the Press this button while the CD is playing to activate CD.
Page 336 334 UNDERSTANDING YOUR INSTRUMENT PANEL Supported Media (Disc Types) a number instead. With a maximum number of files, The MP3 file recording media supported by the radio are exceeding 20 folders will result in this display. With CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. 200 files, exceeding 50 folders will result in this display.) Supported Medium Formats (File Systems)
Page 337 UNDERSTANDING YOUR INSTRUMENT PANEL 335 Supported MP3 File Formats MPEG Sampling Bit Rate (kbps) The radio will recognize only files with the *.MP3 exten- Specification Frequency (kHz) sion as MP3 files. Non-MP3 files named with the *.MP3 320, 256, 224, extension may cause playback problems.
Page 338: Operation Instructions - Auxiliary Mode
336 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files Operation Instructions - Auxiliary Mode When a medium containing MP3 data is loaded, the The auxiliary (AUX) jack is an audio input jack, which radio checks all files on the medium. If the medium allows the user to plug in a portable device, such as an contains a lot of folders or files, the radio will take more MP3 player, or cassette player, and utilize the vehicle’s...
Page 339: Media Center 130 With Satellite Radio (Sales Code Res+Rsc)
UNDERSTANDING YOUR INSTRUMENT PANEL 337 MEDIA CENTER 130 WITH SATELLITE RADIO Operating Instructions — Radio Mode (SALES CODE RES+RSC) NOTE: The ignition switch must be in the ON/RUN or NOTE: The radio sales code is located on the lower right ACC position to operate the radio.
Page 340 338 UNDERSTANDING YOUR INSTRUMENT PANEL to seek up and the left switch to seek down. The radio Phone Button Uconnect™ Phone — If Equipped will remain tuned to the new station until you make Press this button to operate the Uconnect™ Phone feature another selection.
Page 341 UNDERSTANDING YOUR INSTRUMENT PANEL 339 3. After adjusting the hours, press the right side TUNE/ INFO Button SCROLL control knob to set the minutes. The minutes Press the INFO button for an RDS station (one with call will begin to blink. letters displayed).
Page 342 340 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a second MUSIC TYPE Button time and MID will display. Turn the TUNE/SCROLL Pressing this button once will turn on the Music Type control knob to the right or left to increase or decrease the mode for five seconds.
Page 343 UNDERSTANDING YOUR INSTRUMENT PANEL 341 Program Type 16-Digit Character Display Program Type 16-Digit Character Display Information Inform Top 40 Top 40 Jazz Jazz Weather Weather News News By pressing the SEEK button when the Music Type icon Nostalgia Nostalga is displayed, the radio will be tuned to the next frequency Oldies Oldies station with the same selected Music Type name.
Page 344 342 UNDERSTANDING YOUR INSTRUMENT PANEL hours, press the TUNE/SCROLL control knob to set You may add a second station to each pushbutton by the minutes. The minutes will begin to blink. Adjust repeating the above procedure with this exception: Press the minutes using the right side TUNE/SCROLL the SET/RND button twice and SET 2 will show in the control knob.
Page 345: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
UNDERSTANDING YOUR INSTRUMENT PANEL 343 Operation Instructions — CD MODE for CD and If you insert a disc with the ignition ON/RUN and the MP3 Audio Play radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display NOTE: will show the track number, and index time in minutes •...
Page 346 344 UNDERSTANDING YOUR INSTRUMENT PANEL If you have ejected a disc and have not removed it within RW/FF 10 seconds, it will be reloaded. If the CD is not removed, Press and hold FF (Fast Forward) and the CD player will the radio will reinsert the CD but will not play it.
Page 347: Notes On Playing Mp3 Files
UNDERSTANDING YOUR INSTRUMENT PANEL 345 • Maximum number of files: 255 Notes On Playing MP3 Files The radio can play MP3 files; however, acceptable MP3 • Maximum number of folders. (The radio display of file file recording media and formats are limited. When names and folder names is limited.
Page 348 346 UNDERSTANDING YOUR INSTRUMENT PANEL Discs created with an option such as keep disc open after MPEG Sampling Bit Rate (kbps) writing are most likely multisession discs. The use of Specification Frequency (kHz) multisession for CD audio or MP3 playback may result in 320, 256, 224, longer disc loading times.
Page 349: List Button (Cd Mode For Mp3 Play)
UNDERSTANDING YOUR INSTRUMENT PANEL 347 Playback of MP3 Files LIST Button (CD Mode for MP3 Play) When a medium containing MP3 data is loaded, the Pressing the LIST button will bring up a list of all folders radio checks all files on the medium. If the medium on the disc.
Page 350: Uconnect™ Multimedia (Satellite Radio) - If Equipped
348 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for three seconds TIME Button (Auxiliary Mode) to return to elapsed time display. Press this button to change the display to time of day. The time of day will display for five seconds (when the Operation Instructions - Auxiliary Mode ignition is OFF).
Page 351 UNDERSTANDING YOUR INSTRUMENT PANEL 349 radio system in your vehicle. Sirius will supply a wel- using the TUNE/SCROLL control knob until Sirius ID is come kit that contains general information, including selected. Press the TUNE/SCROLL control knob and the how to setup your on-line listening account. For further Sirius ID number will display.
Page 352 350 UNDERSTANDING YOUR INSTRUMENT PANEL Reception Quality SEEK Buttons Satellite reception may be interrupted due to one of the Press and release the SEEK buttons to search for the next following reasons: channel in Satellite mode. Press the right switch to seek up and the left switch to seek down.
Page 353 UNDERSTANDING YOUR INSTRUMENT PANEL 351 RW/FF By pressing the SEEK button when the Music Type Pressing the RW (Rewind) or FF (Fast Forward) buttons function is active, the radio will be tuned to the next causes the tuner to search for the next channel in the channel with the same selected Music Type name.
Page 354: Operating Instructions (Uconnect™ Phone) - If Equipped
352 UNDERSTANDING YOUR INSTRUMENT PANEL SET Button – To Set the Pushbutton Memory Every time a preset button is used, a corresponding When you are receiving a channel that you wish to button number will display. commit to pushbutton memory, press the SET button. Buttons 1 - 6 The symbol SET 1 will now show in the display window.
Page 355: Connecting The Ipod Or External Usb Device
UNDERSTANDING YOUR INSTRUMENT PANEL 353 This feature allows an iPod or external USB device to be Connecting The iPod Or External USB Device plugged into the USB port, located in the glove compart- Use the connection cable to connect an iPod or external ment.
Page 356: Using This Feature
354 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The glove compartment will have a position Using This Feature where the iPod or consumer electronic audio device By using iPod cable or external USB device to connect to cable can be routed through without damaging the cable USB port: when closing the lid.
Page 357: Play Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 355 • Jump backward in the current track by pressing and control mode, audio tracks (if available from audio device) start playing over the vehicle’s audio system. holding the << RW button. Holding the << RW button long enough will jump to the beginning of Play Mode the current track.
Page 358: List Or Browse Mode
356 UNDERSTANDING YOUR INSTRUMENT PANEL to the next screen of data for that track. Once all device, or press the VR button and say Shuffle ON or screens have been viewed, the last INFO button press Shuffle Off . If the RND icon is showing on the radio will go back to the play mode screen on the radio.
Page 359 UNDERSTANDING YOUR INSTRUMENT PANEL 357 • Pressing a PRESET button will display the current fast will scroll through the list faster. During fast scroll, a slight delay in updating the information on list on the top line and the first item in that list on the radio display may be noticeable.
Page 360: Bluetooth Streaming Audio (Btsa)
358 UNDERSTANDING YOUR INSTRUMENT PANEL Bluetooth Streaming Audio (BTSA) CAUTION! Music can be streamed from your cellular phone to the • Leaving the iPod or external USB device (or any Uconnect™ phone system. supported device) anywhere in the vehicle in Controlling BTSA Using Radio Buttons extreme heat or cold can alter the operation or To get into the BTSA mode, press either “AUX”...
Page 361: Uconnect™ Multimedia Video Entertainment System (Ves)™ - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 359 2. After the Ready prompt and the following beep, say UCONNECT™ MULTIMEDIA VIDEO Setup , then Select Audio Devices . ENTERTAINMENT SYSTEM (VES)™ — IF EQUIPPED 3. Say the name of the audio device or ask the Getting Started Uconnect™...
Page 362: Play Video Games
360 UNDERSTANDING YOUR INSTRUMENT PANEL • Cycle the ignition to the ON or ACC position. • Turn on the VES™ player (if equipped on Dual Screen System) by pushing the Power button, located on the far left, or by pressing the button on the Remote Control. •...
Page 363 UNDERSTANDING YOUR INSTRUMENT PANEL 361 When connecting an external source to the AUX input, be sure to follow the standard color coding for the VES™ jacks: NOTE: Certain high-end video games, such as Playsta- tion3 and XBox360 will exceed the power limit of the vehicle’s Power Inverter.
Page 364 362 UNDERSTANDING YOUR INSTRUMENT PANEL Using The Touch-Screen Radio Controls 3. Touch the 1 soft-key and then touch either AUX 1 or AUX 2 in the VES column (depending which AUX input 1. Press the MENU hard-key on the radio faceplate. is used).
Page 365: Listen To An Audio Source On Channel 2 While A Video Is Playing On Channel 1
UNDERSTANDING YOUR INSTRUMENT PANEL 363 Listen To An Audio Source On Channel 2 While A Video Is Playing On Channel 1 Ensure the Remote Control and Headphone switch is on Channel 2. Using The Remote Control 1. Press the MODE button on the Remote Control and the Mode Select Screen will display, unless a video is playing then only a small banner will appear on the bottom of the screen.
Page 366 364 UNDERSTANDING YOUR INSTRUMENT PANEL Using The Touch-Screen Radio Controls 3. To listen to an audio source on Channel 2 while a video is playing on Channel 1, touch the 2 soft-key and 1. Press the MENU hard-key on the radio faceplate. choose an audio source.
Page 367: Dual Video Screen
UNDERSTANDING YOUR INSTRUMENT PANEL 365 Dual Video Screen 3. To watch a DVD on Screen 1 for second row passen- gers, ensure the Remote Control and Headphone switch NOTE: Typically there are two different ways to operate is on Channel 1. the features of the Video Entertainment System (VES)™.
Page 368 366 UNDERSTANDING YOUR INSTRUMENT PANEL Using The Remote Control NOTE: • Channel/Screen 1 select mode information is shown 1. Press the MODE button on the Remote Control. on the left side of the screen. 2. While looking at Screen 1 or 2, highlight DISC by •...
Page 369 UNDERSTANDING YOUR INSTRUMENT PANEL 367 Rear VES Soft-key Select Channel/Screen 1 And DISC In The MEDIA Column 3. Touch the 1 or 2 soft-key based on the channel you NOTE: want to change and then the DISC soft-key in the MEDIA •...
Page 370: Play A Dvd Using The Ves™ Player (If Equipped)
368 UNDERSTANDING YOUR INSTRUMENT PANEL • Viewing a DVD on the Touch-Screen radio screen is NOTE: The VES™ player has basic DVD control func- not available in all states/provinces, and the vehicle tion such as Menu, Play, Pause, FF, RW and Stop must be stopped, and the shift lever must be in the 2.
Page 371 UNDERSTANDING YOUR INSTRUMENT PANEL 369 Using The Touch-Screen Radio Controls 1. Press the MENU hard-key on the radio faceplate. 2. Touch the Rear VES soft-key to display the Rear VES Controls. If a channel list is displayed, touch the HIDE LIST soft-key to display the Rear VES Controls screen.
Page 372: Listen To An Audio Source While A Video Is Playing
370 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Touch the 1 or 2 soft-key and then the DISC soft-key in NOTE: • To view a DVD on the radio press the RADIO/MEDIA the VES column. To exit touch the back arrow soft-key at the top left of the screen.
Page 373 UNDERSTANDING YOUR INSTRUMENT PANEL 371 Using The Remote Control 1. Press the MODE button on the Remote Control and either the Mode Select Screen will display or a small banner will appear at the bottom of the screen. 2. To listen to an audio source on Channel 1 or 2, either press Up/Down/Left/Right on the Remote Control to highlight the desired audio source or press the MODE button repeatedly until the desired audio source appears...
Page 374 372 UNDERSTANDING YOUR INSTRUMENT PANEL Using The Touch Screen Radio Controls 3. To listen to an audio source on Channel 1 while a video is playing on Channel/Screen 2, touch the 1 1. Press the MENU hard-key on the radio faceplate. soft-key and choose an audio source.
Page 375: Third Row Swivel Screen (If Equipped)
UNDERSTANDING YOUR INSTRUMENT PANEL 373 Third Row Swivel Screen (If Equipped) • The third row screen or Screen 2 has the ability to lower and swivel to face forward. • While the swivel screen is facing forward, the second row screen or Screen 1 must be fully open in order for the swivel screen (Screen 2) to work.
Page 376: Important Notes For Dual Video Screen System
374 UNDERSTANDING YOUR INSTRUMENT PANEL Important Notes For Dual Video Screen System Remote Control • VES is able to transmit two channels of stereo audio and video simultaneously. • In split screen mode the left side equates to Channel 1 and the right side equates to Channel 2.
Page 377 UNDERSTANDING YOUR INSTRUMENT PANEL 375 2. Channel Selector Indicators – When a button is / Prev – In radio modes, press to select to the pressed, the currently affected channel or channel button previous station. In disc modes, press to advance to the is illuminated momentarily.
Page 378 376 UNDERSTANDING YOUR INSTRUMENT PANEL disc in a radio with a multiple-disc changer, PROG Up and the disc is stopped, press the SETUP button to access selects the next disc and PROG Down selects the previ- the DVD Setup menu. (see the DVD Setup Menu of this ous disc.
Page 379: Remote Control Storage
UNDERSTANDING YOUR INSTRUMENT PANEL 377 Remote Control Storage The video screen(s) come with a built in storage compart- ment for the remote control which is accessible when the screen is opened. To remove the remote, use your index finger to pull and rotate the remote towards you. Do not try to pull the remote straight down as it will be very difficult to remove.
Page 380: Replacing The Remote Control Batteries
378 UNDERSTANDING YOUR INSTRUMENT PANEL • Replace the batteries, making sure to orient them Locking The Remote Control All remote control functionality can be disabled as a according to the polarity diagram shown. parental control feature. • Replace the battery compartment cover. •...
Page 381: Controls
UNDERSTANDING YOUR INSTRUMENT PANEL 379 Controls The headphone power indicator and controls are located on the right ear cup. NOTE: The rear video system must be turned on before sound can be heard from the headphones. To conserve battery life, the headphones will automatically turn off approximately three minutes after the rear video system is turned off.
Page 382: Replacing The Headphone Batteries
380 UNDERSTANDING YOUR INSTRUMENT PANEL • When both switches are on Channel 2, the Remote is Replacing The Headphone Batteries controlling Channel 2 and the headphones are tuned Each set of headphones requires two AAA batteries for to the audio of the VES™ Channel 2. operation.
Page 383 UNDERSTANDING YOUR INSTRUMENT PANEL 381 How Long Does The Coverage Last? This warranty lasts NATURE WHATSOEVER. Some states and jurisdictions as long as you own the Product. may not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not What Does This Warranty Cover? Except as specified apply to you.
Page 384: System Information
382 UNDERSTANDING YOUR INSTRUMENT PANEL If you have any questions or comments regarding your If the radio functions (FM, AM, or SAT) are in the shared Unwired wireless headphones, please phone 1-888-293- mode with the VES™, only the radio is able to control the 3332 or email customersupport@unwiredtechnology.com.
Page 385 UNDERSTANDING YOUR INSTRUMENT PANEL 383 The VES™ can even control radio modes or video modes 1. Channel 1 Mode while the radio is turned off. The VES™ can access the 2. Channel 1 Shared Status radio modes or disc modes by navigating to those modes on the VES™...
Page 386 384 UNDERSTANDING YOUR INSTRUMENT PANEL Numeric Keypad Menu screen makes it easy to enter a specific tuner frequency, satellite channel, or track number. To enter the desired digit: 1. Press the remote control’s navigation buttons ( , ) to navigate to the desired digit. 2.
Page 387 UNDERSTANDING YOUR INSTRUMENT PANEL 385 press the remote control’s ENTER button to tune to that When listening to a CD Audio or CD Data disc, pressing station. To jump through the list more quickly, navigate the remote control’s MENU button displays a list of all to the Page Up and Page Down icons on the screen.
Page 388 386 UNDERSTANDING YOUR INSTRUMENT PANEL When watching a video source (DVD Video with the disc Listening To Audio With The Screen Closed in Play mode, Aux Video, etc.), pressing the remote To listen to only audio portion of the channel with the control’s SETUP button activates the Display Settings screen closed: menu.
Page 389 UNDERSTANDING YOUR INSTRUMENT PANEL 387 the remote control’s power button to turn audio on. If DVD Region Codes audio is still not heard, check that fully charged batteries The VES™ DVD player and many DVD discs are coded are installed in the headphones. by geographic region.
Page 390 388 UNDERSTANDING YOUR INSTRUMENT PANEL • For CD Data (or CD-ROM) discs, always use the Recorded Discs ISO-9660 (Level 1 or Level 2), Joliet, or Romeo format. The VES™ DVD player will play CD-R and CD-RW discs Other formats (such as UDF, HFS, or others) are not recorded in CD-Audio or Video-CD format, or as a supported.
Page 391 UNDERSTANDING YOUR INSTRUMENT PANEL 389 • Other compression formats such as AAC, MP3 Pro, Compressed Audio Files (MP3 and WMA) Ogg Vorbis, and ATRAC3 will not play. The DVD The DVD player is capable of playing MP3 (MPEG-1 player will automatically skip the file and begin play- Audio Layer 3) and WMA (Windows Media Audio) files ing the next available file.
Page 392 390 UNDERSTANDING YOUR INSTRUMENT PANEL Disc Errors Display Other Language Setup If the DVD player is unable to read the disc, a Disc Error message is displayed on the VES™ and Radio displays and the disc is automatically ejected. A dirty, damaged, or incompatible disc format are all potential causes for a Disc Error message.
Page 393 UNDERSTANDING YOUR INSTRUMENT PANEL 391 • When the entire four-digit code is entered, press the All of the Language settings have a special Other setting to accommodate languages other than Japanese or English. remote control’s ENTER button. If the language code These languages are selected using a special four-digit code.
Page 394 392 UNDERSTANDING YOUR INSTRUMENT PANEL them where lower numbers are designated for all audi- The default rating is Level 8 (play all discs without a ences and higher numbers are designated for more adult password) and the default password is 0000. audiences.
Page 395 UNDERSTANDING YOUR INSTRUMENT PANEL 393 • After the four-digit password is entered, press the To set the password, activate the DVD Setup Menu and follow these additional instructions: remote control’s ENTER button to accept the change. • Using the remote control Left and Right cursor but- tons, select the Rating tab.
Page 396 394 UNDERSTANDING YOUR INSTRUMENT PANEL • Using the remote control’s Up and Down cursor To set the rating, activate the DVD Setup Menu and follow these additional instructions: buttons, select the new rating level, and then press the remote control’s ENTER button to accept the change. •...
Page 397: Steering Wheel Audio Controls - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 395 General Information STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED This system complies with Part 15 of the FCC Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
Page 398: Radio Operation
396 UNDERSTANDING YOUR INSTRUMENT PANEL The right-hand rocker switch has a pushbutton in the Radio Operation center, and controls the volume and mode of the sound Pressing the top of the switch will SEEK up for the next system. Pressing the top of the rocker switch will increase listenable station, and pressing the bottom of the switch the volume.
Page 399: Cd/Dvd Disc Maintenance
UNDERSTANDING YOUR INSTRUMENT PANEL 397 CD/DVD DISC MAINTENANCE NOTE: If you experience difficulty in playing a particu- To keep a CD/DVD in good condition, take the following lar disc, it may be damaged (i.e., scratched, reflective precautions: coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding.
Page 400: Climate Controls
398 UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS The primary control for the rear blower is on the front The Climate Control system allows you to regulate the climate control unit located on the instrument panel. temperature, amount, and direction of air circulating When the front control is in any position other than rear, throughout the vehicle.
Page 401 UNDERSTANDING YOUR INSTRUMENT PANEL 399 2. Rear Blower Control — If Equipped Use this control to regulate the amount of air forced through the rear system in any mode you select. The rear blower speed increases as you move the control to the right from the “O”...
Page 402 400 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Rear Temperature Control — If Equipped 7. Front Defrost Mode Provides temperature control for the rear cabin. Turn left Air is directed through the windshield and side for cooler or right for warmer temperature settings in the window demist outlets.
Page 403 UNDERSTANDING YOUR INSTRUMENT PANEL 401 NOTE: CAUTION! (Continued) • You can turn off the heated mirror feature at anytime • Do not use scrapers, sharp instruments, or abra- by pressing the rear window defroster switch a second sive window cleaners on the interior surface of the time.
Page 404 402 UNDERSTANDING YOUR INSTRUMENT PANEL • In order to prevent fogging, when the Recirculation NOTE: • If the Recirculation button is pressed when the system button is pressed and the mode control is set to Panel, is in Defrost mode the Recirculation LED indicator will the A/C will engage automatically.
Page 405: Rear Manual Climate Control - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 403 11. Floor Mode Button NOTE: For maximum airflow to the rear, the center Air is directed through the floor outlets with a instrument panel outlets can be directed toward the rear small amount through the defrost and side window seat passengers.
Page 406 404 UNDERSTANDING YOUR INSTRUMENT PANEL The rear blower and temperature controls for the rear Rear Blower Control seat passengers are located in the headliner, near the The primary control for the rear blower is on the front center of the vehicle. climate control unit, located on the instrument panel.
Page 407 UNDERSTANDING YOUR INSTRUMENT PANEL 405 When rear controls are locked by the front system, the CAUTION! lock symbol on the temperature knob is illuminated, and the rear overhead adjustments are inoperable. Interior air enters the Rear Manual Climate Control system through an intake grille, located in the right Rear Mode Control side trim panel behind the third row seats.
Page 408: Automatic Temperature Control (Atc) - If Equipped
406 UNDERSTANDING YOUR INSTRUMENT PANEL Floor Mode The Three-Zone ATC system automatically maintains the Air comes from the floor outlets. interior comfort level desired by the driver and all passen- gers. The system automatically adjusts the air temperature, the airflow volume, amount of outside air recirculation and Automatic Temperature Control (ATC) —...
Page 409 UNDERSTANDING YOUR INSTRUMENT PANEL 407 1. Air Conditioning (A/C) Button 7. Right Front Seat Occupant Temperature Display Press and release to change the current Air Conditioning This display shows the temperature setting for the right (A/C) setting, the indicator illuminates when A/C is ON. front seat occupant.
Page 410 408 UNDERSTANDING YOUR INSTRUMENT PANEL 11. Rear Lock 15. Mode Control Button Press and release the Rear Lock button on the front ATC Press and release to select between Modes (Panel, Bi- panel to lock and unlock the rear climate controls Level, Floor, Mix).
Page 411 UNDERSTANDING YOUR INSTRUMENT PANEL 409 Controlling The Rear Climate Controls From The Front ATC Panel The Three-Zone ATC system allows for adjustment of the rear climate controls from the front ATC panel. To change the rear system settings: 1. Press REAR button to change control to rear control mode, Rear display (below) will appear.
Page 412 410 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Blower Control Display 3. When the system is set up for your comfort level, it is This display shows the current Blower speed selection. not necessary to change the settings. You will experience the greatest efficiency by simply allowing the system to 4.
Page 413 UNDERSTANDING YOUR INSTRUMENT PANEL 411 To provide you with maximum comfort in the automatic There are seven fixed blower speeds. mode, during cold start-ups, the blower fan will remain Use the outer dial control to regulate on low until the engine warms up. The fan will engage the amount of air forced through the immediately if the Defrost mode is selected, or by chang- system in any mode you select.
Page 414 412 UNDERSTANDING YOUR INSTRUMENT PANEL Panel Mode Floor Mode Air is directed through the outlets in the instrument Air comes from the floor outlets. A slight amount of panel. These outlets can be adjusted for direction, air is directed through the defrost and side window and turned on or off to control airflow.
Page 415 UNDERSTANDING YOUR INSTRUMENT PANEL 413 Air Conditioning (A/C) Recirculation Control The Air Conditioning (A/C) button allows the operator When outside air contains smoke, odors, or to manually activate or deactivate the air conditioning high humidity, or if rapid cooling is desired, system.
Page 416 414 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Automatic Temperature Control (ATC) — If The rear ATC system is located in the headliner, near the Equipped center of the vehicle. The rear ATC system has floor air outlets at the rear of the right side sliding door, and overhead outlets at each outboard rear seating position.
Page 417 UNDERSTANDING YOUR INSTRUMENT PANEL 415 1. Press the Rear Temperature Lock button on the front NOTE: • It is not necessary to move the temperature settings for ATC panel. This turns off the Rear Temperature Lock icon in the rear temperature knob. cold or hot vehicles.
Page 418 416 UNDERSTANDING YOUR INSTRUMENT PANEL When rear controls are locked by the front system, the CAUTION! Rear Temperature Lock symbol on the temperature knob is illuminated and any rear overhead adjustments are Interior air enters the Rear Automatic Temperature ignored. Control System through an intake grille, located in the right side trim panel behind the third row seats.
Page 419: Summer Operation
UNDERSTANDING YOUR INSTRUMENT PANEL 417 Headliner Mode Summer Operation Air comes from the outlets in the headliner. Each of The engine cooling system in air conditioned vehicles these outlets can be individually adjusted to direct must be protected with a high-quality antifreeze coolant the flow of air.
Page 420: Vacation/Storage
418 UNDERSTANDING YOUR INSTRUMENT PANEL Vacation/Storage Outside Air Intake Before you store your vehicle, or keep it out of service Make sure the air intake, located directly in front of the (i.e., vacation) for two weeks or more, run the air windshield, is free of obstructions such as leaves.
Page 421: Operating Tips
UNDERSTANDING YOUR INSTRUMENT PANEL 419 Operating Tips A/C Air Filter On vehicles equipped with Automatic Temperature Con- trol (ATC), the climate control system filters out dust and pollen from the air. Refer to “Air Conditioning” in “Maintaining Your Vehicle” for filter replacement instructions.
Page 423: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ....425 Automatic Transmission ....431 ▫...
Page 424 422 STARTING AND OPERATING Driving Through Water ....444 Tire Safety Information ....460 ▫...
Page 425 STARTING AND OPERATING 423 ▫ Full Size Spare – If Equipped ... . 475 Fuel Requirements ..... 491 ▫...
Page 426 424 STARTING AND OPERATING ▫ Selection Of Engine Oil For Flexible Fuel Vehicle Loading ..... . 501 Vehicles (E-85) And Gasoline Vehicles ..497 ▫...
Page 427: Starting Procedures
STARTING AND OPERATING 425 STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust the • Do not leave the key fob in or near the vehicle, and inside and outside mirrors, fasten your seat belt, and if do not leave Keyless Enter-N-Go in the ACC or present, instruct all other occupants to buckle their seat ON/RUN mode.
Page 428: Keyless Enter-N-Go - If Equipped
426 STARTING AND OPERATING automatically when the engine is running. If the engine CAUTION! (Continued) fails to start, the starter will disengage automatically in • Shift into or out of REVERSE only after the 10 seconds. If this occurs, turn the ignition switch to the vehicle has come to a complete stop and the engine LOCK position, wait 10 to 15 seconds, then repeat the is at idle speed.
Page 429: Normal Starting
STARTING AND OPERATING 427 2. Insert the ENGINE START/STOP button into the Normal Starting ignition switch with the lettering facing up and readable. Using The ENGINE START/STOP Button 3. Press firmly on the center of the button to secure it into NOTE: Normal starting of either a cold or a warm position.
Page 430 428 STARTING AND OPERATING 2. The ignition switch will return to the OFF position. Keyless Enter-N-Go Functions – With Driver’s Foot OFF The Brake Pedal (In PARK Or NEUTRAL 3. If the shift lever is not in PARK, the ENGINE START/ Position) STOP button must be held for two seconds and vehicle The Keyless Enter-N-Go feature operates similar to an...
Page 431: Extreme Cold Weather (Below -20°F Or 29°C)
STARTING AND OPERATING 429 Extreme Cold Weather (Below –20°F or 29°C) WARNING! (Continued) To ensure reliable starting at these temperatures, use of • Do not attempt to push or tow your vehicle to get an externally powered electric engine block heater (avail- it started.
Page 432: After Starting
430 STARTING AND OPERATING Clearing A Flooded Engine the accelerator pedal all the way to the floor and hold it. (Using ENGINE START/STOP Button) Then, turn the ignition switch to the START position and If the engine fails to start after you have followed the release it as soon as the starter engages.
Page 433: Engine Block Heater - If Equipped
STARTING AND OPERATING 431 ENGINE BLOCK HEATER — IF EQUIPPED AUTOMATIC TRANSMISSION The engine block heater warms the engine, and permits CAUTION! quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a Damage to the transmission may occur if the follow- grounded, three-wire extension cord.
Page 434: Key Ignition Park Interlock
432 STARTING AND OPERATING WARNING! WARNING! (Continued) • Unintended movement of a vehicle could injure • It is dangerous to move the shift lever out of PARK those in or near the vehicle. As with all vehicles, or NEUTRAL if the engine speed is higher than you should never exit a vehicle while the engine is idle speed.
Page 435: Brake/Transmission Shift Interlock System
STARTING AND OPERATING 433 This system prevents the key fob from being removed Fuel Economy (ECON) Mode unless the shift lever is in PARK. The Fuel Economy (ECON) mode can improve the vehi- cle’s overall fuel economy during normal driving condi- NOTE: If a malfunction occurs, the system will trap the tions.
Page 436: Six-Speed Automatic Transmission
434 STARTING AND OPERATING When the Fuel Economy (ECON) Mode is engaged, the Six-Speed Automatic Transmission vehicle control systems will change the following: The shift lever position display (located in the instrument panel cluster) indicates the transmission gear range. You •...
Page 437: Gear Ranges
STARTING AND OPERATING 435 be made using the Electronic Range Select (ERS) shift control (described later in this section). Moving the shift lever to the left or right (–/ +) while in the DRIVE position will select the highest available transmission gear, and will display that gear in the instrument cluster as 6, 5, 4, 3, 2, 1.
Page 438 436 STARTING AND OPERATING When parking on a hill, apply the parking brake before WARNING! (Continued) placing the shift lever in PARK, otherwise the load on the • Your vehicle could move and injure you and others transmission locking mechanism may make it difficult to if it is not completely in PARK.
Page 439 STARTING AND OPERATING 437 WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure • Allowing children to be in a vehicle unattended is those in or near the vehicle. As with all vehicles, dangerous for a number of reasons. A child or you should never exit a vehicle while the engine is others could be seriously or fatally injured.
Page 440 438 STARTING AND OPERATING • With brake pedal released, verify that the shift lever CAUTION! will not move out of PARK. • Before moving the shift lever out of PARK, you REVERSE must turn the ignition switch from the LOCK/OFF This range is for moving the vehicle backward.
Page 441 STARTING AND OPERATING 439 DRIVE WARNING! This range should be used for most city and highway driving. It provides the smoothest upshifts and down- Do not coast in NEUTRAL and never turn off the shifts, and the best fuel economy. The transmission ignition to coast down a hill.
Page 442 440 STARTING AND OPERATING During cold temperatures, transmission operation may PARK, REVERSE, and NEUTRAL will continue to oper- be modified depending on engine and transmission ate. The Malfunction Indicator Light (MIL) may be illu- temperature as well as vehicle speed. This feature im- minated.
Page 443 STARTING AND OPERATING 441 NOTE: Even if the transmission can be reset, we recom- current gear in the instrument cluster, and maintain that mend that you visit your authorized dealer at your earliest gear as the top available gear. Once in ERS mode, tapping possible convenience.
Page 444 442 STARTING AND OPERATING NOTE: To select the proper gear position for maximum Torque Converter Clutch deceleration (engine braking), tap the shift lever to the A feature designed to improve fuel economy has been left (-) repeatedly as the vehicle slows. The transmission included in the automatic transmission on your vehicle.
Page 445: Driving On Slippery Surfaces
STARTING AND OPERATING 443 DRIVING ON SLIPPERY SURFACES Traction When driving on wet or slushy roads, it is possible for a Acceleration layer of water to build up between the tire and road Rapid acceleration on snow covered, wet, or other slip- surface.
Page 446: Flowing/Rising Water
444 STARTING AND OPERATING DRIVING THROUGH WATER Shallow Standing Water Driving through water more than a few inches/ Although your vehicle is capable of driving through centimeters deep will require extra caution to ensure shallow standing water, consider the following Caution safety and prevent damage to your vehicle.
Page 447 STARTING AND OPERATING 445 CAUTION! (Continued) WARNING! • Driving through standing water may cause dam- • Driving through standing water limits your vehi- age to your vehicle’s drivetrain components. Al- cle’s traction capabilities. Do not exceed 5 mph ways inspect your vehicle’s fluids (i.e., engine oil, (8 km/h) when driving through standing water.
Page 448: Power Steering
446 STARTING AND OPERATING • Upon initial start-up in cold weather, the power steer- POWER STEERING The standard power steering system will give you good ing pump may make noise for a short amount of time. vehicle response and increased ease of maneuverability This is due to the cold, thick fluid in the steering in tight spaces.
Page 449: Power Steering Fluid Check
STARTING AND OPERATING 447 Power Steering Fluid Check WARNING! Checking the power steering fluid level at a defined service interval is not required. The fluid should only be Fluid level should be checked on a level surface and checked if a leak is suspected, abnormal noises are with the engine off to prevent injury from moving apparent, and/or the system is not functioning as antici- parts and to ensure accurate fluid level reading.
Page 450 448 STARTING AND OPERATING The foot operated parking brake is positioned below the When the parking brake is applied with the ignition lower left corner of the instrument panel. To apply the switch in the ON position, the “Brake Warning Light” in park brake, firmly push the park brake pedal fully.
Page 451 STARTING AND OPERATING 449 difficult to move the shift lever out of PARK. The parking WARNING! (Continued) brake should always be applied whenever the driver is • Be sure the parking brake is fully disengaged not in the vehicle. before driving; failure to do so can lead to brake failure and a collision.
Page 452: Anti-Lock Brake System (Abs)
450 STARTING AND OPERATING • A slight drop or fall away of the brake pedal at the end ANTI-LOCK BRAKE SYSTEM (ABS) The Anti-Lock Brake System (ABS) provides increased of the stop vehicle stability and brake performance under most WARNING! braking conditions.
Page 453: Anti-Lock Brake Warning Light
STARTING AND OPERATING 451 Anti-Lock Brake Warning Light WARNING! (Continued) The “Anti-Lock Brake Warning Light” moni- • The Anti-Lock Brake System cannot prevent colli- tors the anti-lock brake system. The light will sions, including those resulting from excessive come on when the ignition switch is turned to speed in turns, following another vehicle too the ON position and may stay on for as long as closely, or hydroplaning.
Page 454: Electronic Brake Control System
452 STARTING AND OPERATING If both the “Brake Warning Light” and the “Anti-Lock wheel(s) and engine power is reduced, to provide en- Brake Warning Light” remain on, the ABS and Electronic hanced acceleration and stability. A feature of the TCS Brake Force Distribution (EBD) systems are not function- functions similarly to a limited-slip differential, and ing.
Page 455: Brake Assist System (Bas)
STARTING AND OPERATING 453 brakes. This can help reduce braking distances. The BAS WARNING! complements the ABS. Applying the brakes very quickly • The TCS cannot prevent the natural laws of phys- results in the best BAS assistance. To receive the benefit of the system, you must apply continuous braking pressure ics from acting on the vehicle, nor can it increase during the stopping sequence.
Page 456: Electronic Stability Control (Esc)
454 STARTING AND OPERATING ESC uses sensors in the vehicle to determine the vehicle WARNING! (Continued) path intended by the driver and compares it to the actual • The capabilities of a BAS-equipped vehicle must path of the vehicle. When the actual path does not match never be exploited in a reckless or dangerous the intended path, ESC applies the brake of the appro- manner which could jeopardize the user’s safety...
Page 457 STARTING AND OPERATING 455 ESC On WARNING! (Continued) This mode is the normal operating mode for ESC on • ESC cannot prevent accidents, including those two-wheel drive vehicles. Whenever the vehicle is resulting from excessive speed in turns, driving on started, the ESC system will be in this mode.
Page 458 456 STARTING AND OPERATING again, momentarily press the “ESC Off” switch. This will ESC Activation/Malfunction Indicator Light And restore the normal “ESC On” mode of operation. ESC OFF Indicator Light The “ESC Activation/Malfunction Indicator NOTE: To improve the vehicle’s traction when driving Light”...
Page 459: Hill Start Assist (Hsa)
STARTING AND OPERATING 457 Malfunction Indicator Light” begins to flash during ac- Hill Start Assist (HSA) celeration, ease up on the accelerator and apply as little The HSA system is designed to assist the driver when throttle as possible. Be sure to adapt your speed and starting a vehicle from a stop on a hill.
Page 460 458 STARTING AND OPERATING • Gear selection matches vehicle uphill direction (i.e., Disabling/Enabling HSA vehicle facing uphill is in forward gear; vehicle back- If you wish to turn on or off the HSA system, it can be ing uphill is in REVERSE gear). done using the Customer Programmable Features in the Electronic Vehicle Information Center (EVIC).
Page 461 STARTING AND OPERATING 459 5. Release the clutch pedal. Towing With HSA HSA will provide assistance when starting on a grade 6. Rotate the steering wheel one-half turn to the left. when pulling a trailer. 7. Press the “ESC Off” switch (located in the lower WARNING! switch bank below the climate controls) four times within 20 seconds.
Page 462: Tire Safety Information
460 STARTING AND OPERATING TIRE SAFETY INFORMATION WARNING! (Continued) Tire Markings • HSA is not a parking brake. Always apply the parking brake fully when leaving your vehicle. Also, be certain to leave the transmission in PARK. • Failure to follow these warnings may cause the vehicle to roll down the incline and could collide with another vehicle, object or person, and cause serious or fatal injury.
Page 463 STARTING AND OPERATING 461 • LT (Light Truck) - Metric tire sizing is based on U.S. NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. The size designation for LT-Metric design standards. P-Metric tires have the letter “P” tires is the same as for P-Metric tires except for the molded into the sidewall preceding the size designa- letters “LT”...
Page 464 462 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ..blank..= Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T or S = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm)
Page 465 STARTING AND OPERATING 463 EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
Page 466: Tire Identification Number (Tin)
464 STARTING AND OPERATING Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side.
Page 467: Tire Terminology And Definitions
STARTING AND OPERATING 465 Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located behind the front door. Cold Tire Inflation Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
Page 468: Tire Loading And Tire Pressure
466 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
Page 469 STARTING AND OPERATING 467 axles must not be exceeded. For further information on This placard tells you important information about GAWRs, vehicle loading, and trailer towing, refer to the: “Vehicle Loading” in this section. 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of...
Page 470 468 STARTING AND OPERATING 3. Subtract the combined weight of the driver and pas- NOTE: • The following table shows examples on how to calcu- sengers from XXX lbs or XXX kg. late total load, cargo/luggage, and towing capacities 4. The resulting figure equals the available amount of of your vehicle with varying seating configurations cargo and luggage load capacity.
Page 471 STARTING AND OPERATING 469...
Page 472: Tires - General Information
470 STARTING AND OPERATING Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause collisions. recommended load capacity for your vehicle.
Page 473: Tire Inflation Pressures
STARTING AND OPERATING 471 Tire Inflation Pressures WARNING! (Continued) The proper cold tire inflation pressure is listed on the • Unequal tire pressures from one side of the ve- driver’s side “B” Pillar or rear edge of the driver’s side hicle to the other can cause the vehicle to drift to door.
Page 474: Tire Pressures For High-Speed Operation
472 STARTING AND OPERATING Inflation pressures specified on the placard are always Example: If garage temperature is 68°F (20°C) and the “cold tire inflation pressure.” Cold tire inflation pressure outside temperature is 32°F (0°C), then the cold tire is defined as the tire pressure after the vehicle has not inflation pressure should be increased by 3 psi (21 kPa), been driven for at least three hours, or driven less than which equals 1 psi (7 kPa) for every 12°F (7°C) for this...
Page 475: Radial-Ply Tires
STARTING AND OPERATING 473 Cuts and punctures in radial tires are repairable only in WARNING! the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs. High-speed driving, with your vehicle at or above maximum load, is dangerous. The added strain on Spare Tire Matching Original Equipped Tire And your tires could cause them to fail.
Page 476: Compact Spare Tire - If Equipped
474 STARTING AND OPERATING If your vehicle is not equipped with an original equip- Compact Spare Tire – If Equipped ment tire and wheel as a spare, a non-matching tempo- The compact spare is for temporary emergency use only. rary emergency use spare may be equipped with your You can identify if your vehicle is equipped with a vehicle.
Page 477: Full Size Spare - If Equipped
STARTING AND OPERATING 475 your original equipment tire, replace (or repair) the WARNING! original equipment tire and reinstall on the vehicle at the first opportunity. Compact spares are for temporary emergency use only. With these spares, do not drive more than Limited-Use Spare –...
Page 478: Tire Spinning
476 STARTING AND OPERATING Refer to “Freeing A Stuck Vehicle” in “What To Do In WARNING! Emergencies” for further information. Limited-use spares are for emergency use only. In- WARNING! stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the •...
Page 479: Life Of Tire
STARTING AND OPERATING 477 Life Of Tire The service life of a tire is dependent upon varying factors, including, but not limited to: • Driving style • Tire pressure • Distance driven WARNING! The tires and the spare tire should be replaced after six years, regardless of the remaining tread.
Page 480: Replacement Tires
478 STARTING AND OPERATING Replacement Tires It is recommended you contact your original equipment The tires on your new vehicle provide a balance of many or an authorized tire dealer with any questions you may characteristics. They should be inspected regularly for have on tire specifications or capability.
Page 481: Tire Chains
STARTING AND OPERATING 479 TIRE CHAINS WARNING! (Continued) Use only compact chains, or other traction aids that meet • Never use a tire with a smaller load index or SAE type “Class S” specifications. Chains must be the capacity, than what was originally equipped on proper size for the vehicle, as recommended by the chain your vehicle.
Page 482: Snow Tires
480 STARTING AND OPERATING CAUTION! (Continued) CAUTION! (Continued) • Because of restricted chain clearance between tires • Observe the tire chain manufacturer’s instructions and other suspension components, it is important on the method of installation, operating speed, that only chains in good condition are used. Bro- and conditions for use.
Page 483: Tire Rotation Recommendations
STARTING AND OPERATING 481 If you need snow tires, select tires equivalent in size and TIRE ROTATION RECOMMENDATIONS type to the original equipment tires. Use snow tires only The tires on the front and rear of your vehicle operate at in sets of four;...
Page 484: Tire Pressure Monitor System (Tpms)
482 STARTING AND OPERATING The suggested rotation method is the “rearward cross” TIRE PRESSURE MONITOR SYSTEM (TPMS) shown in the following diagram. This rotation pattern The TPMS will warn the driver of a low tire pressure does not apply to some directional tires that must not be based on the cold inflation tire placard pressure require- reversed.
Page 485 STARTING AND OPERATING 483 The TPMS will warn the driver of a low tire pressure if For example, your vehicle may have a recommended the tire pressure falls below the low pressure warning cold (parked for more than three hours) tire placard threshold for any reason, including low temperature pressure of 35 psi (241 kPa).
Page 486 484 STARTING AND OPERATING NOTE: CAUTION! • The TPMS is not intended to replace normal tire care • The TPMS has been optimized for the original and maintenance, or to provide warning of a tire failure or condition. equipment tires and wheels. TPMS pressures have been established for the tire size equipped on your •...
Page 487: Base System
STARTING AND OPERATING 485 • Seasonal temperature changes will affect tire pressure, Tire Pressure Monitoring Low Tire Pressure and the TPMS will monitor the actual tire pressure in Warnings the tire. The “Tire Pressure Monitoring Telltale Light” will illuminate in the instrument cluster, a Base System “LOW TIRE PRESSURE”...
Page 488 486 STARTING AND OPERATING The “Tire Pressure Monitoring Telltale Light” will flash Vehicles With Compact Spare on and off for 75 seconds, and remain on solid when a 1. The compact spare tire (if equipped) does not have a system fault is detected. The system fault will also sound TPMS sensor.
Page 489: Premium System - If Equipped
STARTING AND OPERATING 487 5. Once you repair or replace the original road tire and The Premium TPMS consists of the following compo- reinstall it on the vehicle in place of the compact spare nents: tire, the TPMS will automatically update, and the “Tire •...
Page 490 488 STARTING AND OPERATING Should a low tire condition occur on any of the four message is then followed by a graphic display, with - - in active road tire(s), you should stop as soon as possible, place of the pressure value(s) indicating which TPMS and inflate the low tire(s) that is flashing on the graphic Sensor(s) is not being received.
Page 491 STARTING AND OPERATING 489 4. Using tire chains on the vehicle. Vehicles With Compact Spare 5. Using wheels/tires not equipped with TPMS sensors. 1. The compact spare tire (if equipped) does not have a TPMS. Therefore, the TPMS will not monitor the pressure The EVIC will also display a “SERVICE TPM SYSTEM”...
Page 492 490 STARTING AND OPERATING 4. For each subsequent ignition switch cycle, a chime will General Information sound, the “Tire Pressure Monitoring Telltale Light” will This device complies with Part 15 of the FCC rules and flash on and off for 75 seconds and then remain on solid, RSS 210 of Industry Canada.
Page 493: Fuel Requirements
STARTING AND OPERATING 491 FUEL REQUIREMENTS Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the World- 3.6L Engine wide Fuel Charter, WWFC) which define fuel properties This engine is designed to meet all emis- necessary to deliver enhanced emissions, performance, sions regulations and provide excellent and durability for your vehicle.
Page 494: Gasoline/Oxygenate Blends
492 STARTING AND OPERATING Gasoline/Oxygenate Blends E-85 Usage In Non-Flex Fuel Vehicles Some fuel suppliers blend unleaded gasoline with oxy- Non-FFV vehicles are compatible with gasoline contain- genates such as Ethanol. Fuels blended with oxygenates ing 10% ethanol (E10). Gasoline with higher ethanol may be used in your vehicle.
Page 495: Mmt In Gasoline
STARTING AND OPERATING 493 • drain the fuel tank (see your authorized dealer) Materials Added To Fuel All gasoline sold in the United States is required to More extensive repairs will be required for prolonged contain effective detergent additives. Use of additional exposure to E-85 fuel.
Page 496: Carbon Monoxide Warnings
494 STARTING AND OPERATING Carbon Monoxide Warnings CAUTION! (Continued) • An out-of-tune engine or certain fuel or ignition WARNING! malfunctions can cause the catalytic converter to Carbon monoxide (CO) in exhaust gases is deadly. overheat. If you notice a pungent burning odor or Follow the precautions below to prevent carbon some light smoke, your engine may be out of tune monoxide poisoning:...
Page 497: Flexible Fuel - If Equipped
STARTING AND OPERATING 495 the other sections of this manual for information on WARNING! (Continued) features that are common between Flexible Fuel and • Guard against carbon monoxide with proper gasoline-only powered vehicles. maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnor- mal conditions repaired promptly.
Page 498: Ethanol Fuel (E-85)
496 STARTING AND OPERATING Ethanol Fuel (E-85) CAUTION! E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. Only vehicles with the E-85 fuel filler door label can operate on E-85. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury.
Page 499: Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles
MOPAR engine oils, and in equivalent oils meeting during warm up. Chrysler Specification MS-6395. The manufacturer re- NOTE: quires engine oils that are API Certified and meet the • When the ambient temperature is above 90° F (32° C), requirements of Material Standard MS-6395.
Page 500: Starting
498 STARTING AND OPERATING Starting Replacement Parts The characteristics of E-85 fuel make it unsuitable for use Many components in your Flexible Fuel Vehicle (FFV) are when ambient temperatures fall below 0°F (-18°C). In the designed to be compatible with ethanol. Always be sure range of 0°F (-18°C) to 32°F (0°C), you may experience an that your vehicle is serviced with correct ethanol com- increase in the time it takes for your engine to start, and...
Page 501: Adding Fuel
STARTING AND OPERATING 499 ADDING FUEL NOTE: The driver’s side sliding door cannot be opened while the fuel door is open. This feature operates only Fuel Filler Cap (Gas Cap) when the sliding door is fully closed prior to opening the The gas cap is located behind the fuel filler door on the fuel door.
Page 502: Loose Fuel Filler Cap Message
500 STARTING AND OPERATING • If the gas cap is not tightened properly, the MIL may WARNING! come on. Be sure the gas cap is tightened every time • Never have any smoking materials lit in or near the vehicle is refueled. the vehicle when the gas cap is removed or the Loose Fuel Filler Cap Message tank is being filled.
Page 503: Vehicle Loading
STARTING AND OPERATING 501 • Vehicle Identification Number (VIN) VEHICLE LOADING As required by National Highway Traffic Safety Admin- • Type of Vehicle istration regulations, your vehicle has a certification label • Month, Day and Hour of Manufacture (MDH) affixed to the driver’s side door or B-Pillar. If seats are removed for carrying cargo, do not exceed the The bar code allows a computer scanner to read the specified GVWR and GAWR.
Page 504 502 STARTING AND OPERATING Curb Weight WARNING! The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full Because the front wheels drive and steer the vehicle, capacity conditions, and with no occupants or cargo it is important that you do not exceed the maximum loaded into the vehicle.
Page 505: Trailer Towing
STARTING AND OPERATING 503 Figure out the weight on the front and rear of the vehicle CAUTION! separately. It is important that you distribute the load evenly over the front and rear axles. Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR.
Page 506: Common Towing Definitions
504 STARTING AND OPERATING Common Towing Definitions Gross Combination Weight Rating (GCWR) The following trailer towing-related definitions will as- The GCWR is the total permissible weight of your vehicle sist you in understanding the following information: and trailer when weighed in combination. Gross Vehicle Weight Rating (GVWR) NOTE: The GCWR rating includes a 150 lbs (68 kg) The GVWR is the total allowable weight of your vehicle.
Page 507 STARTING AND OPERATING 505 that typically provides adjustable friction associated with WARNING! the telescoping motion to dampen any unwanted trailer swaying motions while traveling. It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition Weight-Carrying Hitch can result if either rating is exceeded.
Page 508 506 STARTING AND OPERATING safety. The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability. Trailer sway control and a weight distributing (load equalizing) hitch are recommended for heavier tongue weights (TW), and may be required depending on vehicle and trailer configuration/loading to comply with gross axle weight rating (GAWR) requirements.
Page 509 STARTING AND OPERATING 507 With Weight-Distributing Hitch (Correct) Improper Adjustment of Weight-Distributing Hitch (Incorrect)
Page 510 508 STARTING AND OPERATING Trailer Hitch Classification TRAILER HITCH CLASSIFICATIONS The following chart provides the industry standard for Max. GTW Class the maximum trailer weight a given trailer hitch class can (Gross Trailer Wt.) tow, and should be used to assist you in selecting the Class I - Light Duty 2,000 lbs (907 kg) correct trailer hitch for your intended towing condition.
Page 511 STARTING AND OPERATING 509 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. GCWR (Gross Com- Max. GTW (Gross Engine/Transmission Frontal Area Max. Tongue Wt. bined Wt. Rating) Trailer Wt.) Up to 2 persons &...
Page 512 510 STARTING AND OPERATING Trailer And Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
Page 513 STARTING AND OPERATING 511 NOTE: Remember that everything put into or on the CAUTION! (Continued) trailer adds to the load on your vehicle. Also, additional • Then, during the first 500 miles (805 km) that a factory-installed options, or authorized dealer-installed trailer is towed, do not drive over 50 mph options, must be considered as part of the total load on (80 km/h) and do not make starts at full throttle.
Page 514 512 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Make certain that the load is secured in the trailer • Vehicles with trailers should not be parked on a and will not shift during travel. When trailering grade. When parking, apply the parking brake on cargo that is not fully secured, dynamic load shifts the tow vehicle.
Page 515 STARTING AND OPERATING 513 Towing Requirements – Tires replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s • Do not attempt to tow a trailer while using a compact GVWR and GAWR limits. spare tire. Towing Requirements –...
Page 516 514 STARTING AND OPERATING CAUTION! WARNING! (Continued) • Towing any trailer will increase your stopping If the trailer weighs more than 1,000 lbs (454 kg) distance. When towing you should allow for addi- loaded, it should have its own brakes and they tional space between your vehicle and the vehicle should be of adequate capacity.
Page 517 STARTING AND OPERATING 515 The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following four-pin connector and seven-pin connector illustrations. Seven-Pin Connector 1 — Battery 5 — Ground 2 —...
Page 518: Towing Tips
516 STARTING AND OPERATING Towing Tips Electronic Speed Control – If Equipped Before setting out on a trip, practice turning, stopping • Do not use in hilly terrain or with heavy loads. and backing the trailer in an area away from heavy •...
Page 519: Recreational Towing (Behind Motorhome, Etc.)
STARTING AND OPERATING 517 RECREATIONAL TOWING NOTE: This vehicle may be towed on a flatbed or (BEHIND MOTORHOME, ETC.) vehicle trailer provided all four wheels are OFF the ground. Towing This Vehicle Behind Another Vehicle Recreational towing is not allowed. CAUTION! CAUTION! Towing this vehicle in violation of the above require-...
Page 521: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS ▫ Preparations For Jacking ....530 Hazard Warning Flashers ....521 ▫...
Page 522 520 WHAT TO DO IN EMERGENCIES Freeing A Stuck Vehicle ....544 Towing A Disabled Vehicle ....547 ▫...
Page 523: Hazard Warning Flashers
WHAT TO DO IN EMERGENCIES 521 HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located in the In any of the following situations, you can reduce the lower center area of the instrument panel. potential for overheating by taking the appropriate ac- tion.
Page 524: Jacking And Tire Changing
522 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING CAUTION! WARNING! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull • Do not attempt to change a tire on the side of the over and stop the vehicle.
Page 525: Jack Location
WHAT TO DO IN EMERGENCIES 523 WARNING! (Continued) • The jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas.
Page 526: Spare Tire Removal
524 WHAT TO DO IN EMERGENCIES Spare Tire Removal To Access Spare Tire Winch Drive Nut The spare tire is stowed inside a protective cover located To access the spare tire winch drive nut and lower the under the center of the vehicle between the front doors by spare tire, you will need to refer to one of the following means of a cable winch mechanism.
Page 527 WHAT TO DO IN EMERGENCIES 525 Super Console Lower Drawer 2. Open the front drawer to expose the storage compart- 1 — Lower Drawer 2 — Front Drawer ment. 3 — Front Drawer Liner 1. Pull the lower drawer out from the rear of the floor console.
Page 528: Spare Tire Tools
526 WHAT TO DO IN EMERGENCIES 3. Remove the liner from the console’s storage compart- ment to access the spare tire winch drive nut. Winch Cover Assembly Plug (If Equipped) Spare Tire Tools The tool pouch contains three pieces and can be as- Drive Nut Access sembled into a spare tire hook;...
Page 529 WHAT TO DO IN EMERGENCIES 527 Assembled T-handle Assembling The Spare Tire Hook A — Spare Tire Hook/T-handle A — Spare Tire Hook/T-handle B — Extension 1 B — Extension 1 C — Extension 2 C — Extension 2...
Page 530: Spare Tire Removal Instructions
528 WHAT TO DO IN EMERGENCIES Spare Tire Removal Instructions 2. Rotate the nut to the left until the winch mechanism The spare tire is located under the vehicle beneath the stops turning freely. This will allow enough slack in the center console area.
Page 531 WHAT TO DO IN EMERGENCIES 529 4. Stand the tire/cover assembly upright and remove the wheel spacer by squeezing the winch retaining tabs together. Push the retainer through the spare tire to release it from the wheel. Pulling Spare Tire NOTE: If either front tire is flat it may be necessary to jack up the vehicle to remove the compact spare tire/ cover assembly from under the vehicle.
Page 532: Preparations For Jacking
530 WHAT TO DO IN EMERGENCIES Preparations For Jacking 4. Place the shift lever into PARK. 1. Park the vehicle on a firm, level surface. Avoid ice or 5. Turn OFF the ignition. slippery areas. 6. Block both the front and rear of the wheel diagonally opposite the jacking WARNING! position.
Page 533: Jacking Instructions
WHAT TO DO IN EMERGENCIES 531 Jacking Instructions WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a WARNING! jack. Carefully follow these tire changing warnings to • Do not get under the vehicle when it is on a jack. help prevent personal injury or damage to your •...
Page 534 532 WHAT TO DO IN EMERGENCIES CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. NOTE: Refer to the “Compact Spare Tire” section of “Tires – General Information” for information about the spare tire, its use, and operation.
Page 535 WHAT TO DO IN EMERGENCIES 533 Front Jack Locations Rear Jacking Locations NOTE: In some situations the jack may need to be Front jack location is on the sill flange of the vehicle body and is located 6 in (150 mm) from door edge. placed on its side in order to be pushed under the vehicle.
Page 536 534 WHAT TO DO IN EMERGENCIES WARNING! WARNING! Being under a jacked-up vehicle is dangerous. The Raising the vehicle higher than necessary can make vehicle could slip off the jack and fall on you. You the vehicle less stable. It could slip off the jack and could be crushed.
Page 537 WHAT TO DO IN EMERGENCIES 535 NOTE: Do not install the wheel cover on the compact spare. 7. Lower the vehicle by turning the jack screw to the left. 8. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased leverage.
Page 538: Securing The Spare Tire
536 WHAT TO DO IN EMERGENCIES NOTE: Refer to the “Spare Tire Tools” section for WARNING! instructions on assembling the T-handle. A loose tire or jack thrown forward in a collision or 12. Stow the jack, jack handle and winch handle tools hard stop could endanger the occupants of the ve- back in the stowage compartment.
Page 539 WHAT TO DO IN EMERGENCIES 537 3. Turn the compact spare tire so that the valve stem is WARNING! down, and place the tire into the spare tire/cover assem- bly. Slide the wheel spacer through the center of the A loose compact spare tire/cover assembly, thrown wheel and spare tire/cover assembly, so that the two forward in a collision or hard stop could endanger retainer tabs snap out and engage the spare tire cover on...
Page 540: Road Tire Installation
538 WHAT TO DO IN EMERGENCIES WARNING! CAUTION! Verify that both retainer tabs of the wheel spacer The winch mechanism is designed specifically to have been properly extended through the center of stow a compact spare tire only. Do not attempt to use the wheel and spare tire/cover assembly.
Page 541 WHAT TO DO IN EMERGENCIES 539 4. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered.
Page 542: Jump-Starting Procedure
540 WHAT TO DO IN EMERGENCIES correct tightness, have them checked with a torque 3. Lower the vehicle to the ground by turning the jack wrench by your authorized dealer or service station. handle counterclockwise. 7. After 25 miles (40 km) check the lug nut torque with a 4.
Page 543: Preparations For Jump-Start
WHAT TO DO IN EMERGENCIES 541 NOTE: When using a portable battery booster pack Preparations For Jump-Start follow the manufacturer’s operating instructions and The battery in your vehicle is located on the left side of precautions. the engine compartment. CAUTION! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor,...
Page 544: Jump-Starting Procedure
542 WHAT TO DO IN EMERGENCIES 3. If using another vehicle to jump-start the battery, park WARNING! the vehicle within the jumper cables reach, set the • Take care to avoid the radiator cooling fan when- parking brake and make sure the ignition is OFF. ever the hood is raised.
Page 545 WHAT TO DO IN EMERGENCIES 543 CAUTION! WARNING! Failure to follow these procedures could result in Do not connect the cable to the negative post (-) of the damage to the charging system of the booster vehicle discharged battery. The resulting electrical spark or the discharged vehicle.
Page 546: Freeing A Stuck Vehicle
544 WHAT TO DO IN EMERGENCIES 8. Disconnect the opposite end of the positive (+) jumper FREEING A STUCK VEHICLE cable from the positive (+) post of the booster battery. If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion.
Page 547: Shift Lever Override
WHAT TO DO IN EMERGENCIES 545 NOTE: To improve the vehicle’s traction when starting WARNING! off in deep snow, sand or gravel, it may be desirable to switch the Electronic Stability Program (ESP) to “Partial Fast spinning tires can be dangerous. Forces gener- Off”...
Page 548 546 WHAT TO DO IN EMERGENCIES 2. Remove the shift lever override access cover located 3. Turn the ignition switch to the ON/RUN position near the top right of the shift lever in the instrument without starting the engine. panel. 4.
Page 549: Towing A Disabled Vehicle
WHAT TO DO IN EMERGENCIES 547 TOWING A DISABLED VEHICLE Towing Condition Wheels OFF the Ground ALL MODELS Flat Tow NONE If transmission is operable: • Transmission in NEUTRAL • 25 mph (40 km/h)max speed Rear Wheel lift • 15 miles (24 km) max distance Front Flatbed BEST METHOD...
Page 550 548 WHAT TO DO IN EMERGENCIES The manufacturer recommends towing your vehicle with CAUTION! all four wheels OFF the ground using a flatbed. If flatbed • Do not use sling type equipment when towing. equipment is not available, and the transmission is operable, the vehicle may be flat towed (with all four Damage to the fascia will occur.
Page 551: Without The Ignition Key
WHAT TO DO IN EMERGENCIES 549 the ground) is not allowed, as transmission damage will CAUTION! occur. If rear towing is the only alternative, the front wheels must be placed on a towing dolly. Proper towing Towing faster than 25 mph (40 km/h) or farther than equipment is necessary to prevent damage to the vehicle.
Page 553: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS ▫ Engine Oil Filter ..... 560 Engine Compartment — 3.6L ... . . 553 ▫...
Page 554 552 MAINTAINING YOUR VEHICLE ▫ Automatic Transmission ....577 ▫ Front Park/Turn Signal Lamp ... 595 ▫...
Page 555: Engine Compartment - 3.6L
MAINTAINING YOUR VEHICLE 553 ENGINE COMPARTMENT — 3.6L 1 — Air Filter 6 — Engine Coolant Reservoir 2 — Power Steering Fluid Reservoir 7 — Engine Oil Dipstick 3 — Brake Fluid Reservoir 8 — Engine Oil Fill 4 — Battery 9 —...
Page 556: Onboard Diagnostic System - Obd Ii
554 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic further damage to the emission control system.
Page 557: Emissions Inspection And Maintenance Programs
MAINTAINING YOUR VEHICLE 555 “Electronic Vehicle Information Center (EVIC)” in ”Un- For states that require an Inspection and Mainte- derstanding Your Instrument Panel” for further informa- nance (I/M), this check verifies the “Malfunction tion. Tighten the gas cap until a clicking sound is heard. Indicator Light (MIL)”...
Page 558 556 MAINTAINING YOUR VEHICLE 2. If you crank or start the engine, you will have to start If your OBD II system is not ready, you should see your this test over. authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, 3.
Page 559: Replacement Parts
MAINTAINING YOUR VEHICLE 557 REPLACEMENT PARTS WARNING! Use of genuine MOPAR parts for normal/scheduled maintenance and repairs is highly recommended to en- You can be badly injured working on or around a sure the designed performance. Damage or failures motor vehicle. Only do service work for which you caused by the use of non-MOPAR parts for maintenance have the knowledge and the proper equipment.
Page 560: Engine Oil
Immediately have potential malfunctions fully warmed engine is shut OFF or before starting the examined by an authorized Chrysler Group LLC engine after it has sat overnight. dealership or qualified repair center.
Page 561 Engine Oil Selection not covered by the New Vehicle Limited Warranty. For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are API certified and meet the requirements of Chrysler Material Standard MS-6395.
Page 562: Engine Oil Filter
560 MAINTAINING YOUR VEHICLE Engine Oil Viscosity (SAE Grade) Materials Added To Engine Oil SAE 5W-30 engine oil is recommended for all operating The manufacturer strongly recommends against the ad- temperatures. This engine oil improves low temperature dition of any additives (other than leak detection dyes) to starting and vehicle fuel economy.
Page 563: Engine Air Cleaner Filter
MAINTAINING YOUR VEHICLE 561 Engine Oil Filter Selection WARNING! The manufacturer’s engines have a full-flow type oil filter. Use a filter of this type for replacement. The quality The air induction system (air cleaner, hoses, etc.) can of replacement filters varies considerably. Only high provide a measure of protection in the case of engine quality filters should be used to assure most efficient backfire.
Page 564: Exhaust System
562 MAINTAINING YOUR VEHICLE Exhaust System WARNING! The best protection against carbon monoxide entry into • Exhaust gases can injure or kill. They contain the vehicle body is a properly maintained engine exhaust system. carbon monoxide (CO), which is colorless and odorless.
Page 565 MAINTAINING YOUR VEHICLE 563 Under normal operating conditions, the catalytic con- CAUTION! verter will not require maintenance. However, it is im- • The catalytic converter requires the use of un- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst leaded fuel only.
Page 566: Maintenance-Free Battery
564 MAINTAINING YOUR VEHICLE To minimize the possibility of catalytic converter dam- WARNING! age: • Battery fluid is a corrosive acid solution and can • Do not shut off the engine or interrupt the ignition, burn or even blind you. Do not allow battery fluid when the transmission is in gear and the vehicle is in to contact your eyes, skin, or clothing.
Page 567: Air Conditioner Maintenance
MAINTAINING YOUR VEHICLE 565 Air Conditioner Maintenance CAUTION! For best possible performance, your air conditioner • It is essential when replacing the cables on the should be checked and serviced by an authorized dealer at the start of each warm season. This service should battery that the positive cable is attached to the include cleaning of the condenser fins and a system positive post and the negative cable is attached to...
Page 568 566 MAINTAINING YOUR VEHICLE Refrigerant Recovery And Recycling WARNING! R-134a air conditioning refrigerant is a hydrofluoro- • Use only refrigerants and compressor lubricants carbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. How- approved by the manufacturer for your air condi- ever, the manufacturer recommends that air conditioning tioning system.
Page 569 MAINTAINING YOUR VEHICLE 567 WARNING! Do not remove the A/C air filter while the blower is operating or personal injury may result. The A/C air filter is located in the fresh air inlet behind the glove box. Perform the following procedure to re- place the filter: 1.
Page 570: Body Lubrication
568 MAINTAINING YOUR VEHICLE hood latching components to ensure proper function. CAUTION! When performing other underhood services, the hood latch, release mechanism and safety catch should be The A/C air filter is identified with an arrow to cleaned and lubricated. indicate airflow direction through the filter.
Page 571 MAINTAINING YOUR VEHICLE 569 Avoid using the wiper blades to remove frost or ice from WARNING! the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care NOTE: Life expectancy of wiper blades varies depend- must be exercised when filling or working around ing on geographical area and frequency of use.
Page 572: Cooling System
570 MAINTAINING YOUR VEHICLE Cooling System rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front of WARNING! the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden •...
Page 573 MAINTAINING YOUR VEHICLE 571 Cooling System – Drain, Flush, And Refill CAUTION! If the engine coolant (antifreeze) is dirty or contains a • Mixing of engine coolant (antifreeze) other than considerable amount of sediment, clean and flush with a specified Hybrid Organic Additive Technology reliable cooling system cleaner.
Page 574 572 MAINTAINING YOUR VEHICLE • Mix a minimum solution of 50% HOAT engine coolant Adding Coolant Your vehicle has been built with an improved engine and distilled water. Use higher concentrations (not to coolant (antifreeze) that allows extended maintenance exceed 70%) if temperatures below 34°F ( 37°C) are intervals.
Page 575 MAINTAINING YOUR VEHICLE 573 Cooling System Pressure Cap WARNING! (Continued) The cap must be fully tightened to prevent the loss of • Do not use a pressure cap other than the one engine coolant (antifreeze), and to ensure that engine specified for your vehicle.
Page 576 574 MAINTAINING YOUR VEHICLE Coolant Level Points To Remember The coolant bottle provides a quick visual method for NOTE: When the vehicle is stopped after a few miles (a determining that the coolant level is adequate. With the few kilometers) of operation, you may observe vapor engine cold, the level of the engine coolant (antifreeze) in coming from the front of the engine compartment.
Page 577: Brakes
MAINTAINING YOUR VEHICLE 575 • If frequent engine coolant (antifreeze) additions are Brakes required, or if the level in the coolant recovery bottle In order to assure brake system performance, all brake does not drop when the engine cools, the cooling system components should be inspected periodically.
Page 578 576 MAINTAINING YOUR VEHICLE Clean the top of the master cylinder area before removing WARNING! the cap. Add fluid to bring the level up to the top of the • Use only manufacturer’s recommended brake “FULL” mark on the side of the master cylinder reservoir. fluid.
Page 579: Automatic Transmission
MAINTAINING YOUR VEHICLE 577 WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or • Do not allow petroleum based fluid to contami- moisture, use only new brake fluid or fluid that nate the brake fluid. Brake seal components could has been in a tightly closed container.
Page 580 578 MAINTAINING YOUR VEHICLE Selection Of Lubricant CAUTION! It is important that the proper lubricant is used in the transmission to assure optimum transmission perfor- Using a transmission fluid other than the manufac- mance. Use only the manufacturer’s recommended trans- turer’s recommended fluid may cause deterioration mission fluid.
Page 581: Appearance Care And Protection From Corrosion
MAINTAINING YOUR VEHICLE 579 Appearance Care And Protection From Corrosion CAUTION! Protection Of Body And Paint From Corrosion Do not use chemical flushes in your transmission as Vehicle body care requirements vary according to geo- the chemicals can damage your transmission compo- graphic locations and usage.
Page 582 580 MAINTAINING YOUR VEHICLE • Use a high quality cleaner wax, such as MOPAR The most common causes are: Cleaner Wax or equivalent to remove road film, stains • Road salt, dirt and moisture accumulation and to protect your paint finish. Take care never to •...
Page 583 MAINTAINING YOUR VEHICLE 581 • If a lot of driving is done on gravel roads, consider Special Care mud or stone shields behind each wheel. • If you drive on salted or dusty roads or if you drive • Use MOPAR near the ocean, hose off the undercarriage at least once Touch Up Paint or equivalent on a month.
Page 584 582 MAINTAINING YOUR VEHICLE • For tough stains, apply MOPAR Total Clean or CAUTION! equivalent, or a mild soap solution to a clean, damp cloth and remove the stain. Use a fresh, damp towel to Do not use scouring pads, steel wool, a bristle brush, remove soap residue.
Page 585 MAINTAINING YOUR VEHICLE 583 Cleaning Interior Trim solvents, detergents, or ammonia-based cleaners to clean Interior trim should be cleaned starting with a damp your leather upholstery. Application of a leather condi- cloth, a damp cloth with MOPAR Total Clean or equiva- tioner is not required to maintain the original condition.
Page 586 584 MAINTAINING YOUR VEHICLE To minimize the possibility of scratching the lenses and Cleaning Plastic Instrument Cluster Lenses reducing light output, avoid wiping with a dry cloth. To The lenses in front of the instruments in this vehicle are remove road dirt, wash with a mild soap solution fol- molded in clear plastic.
Page 587: Cleaning The Instrument Panel Cupholders
MAINTAINING YOUR VEHICLE 585 Replace the seat belts if they appear frayed or worn, or if approximately 30 minutes. After 30 minutes, pull the the buckles do not work properly. liner from the water and dip it back into the water about six times.
Page 588: Fuses
586 MAINTAINING YOUR VEHICLE FUSES Totally Integrated Power Module The Totally Integrated Power Module is located in the engine compartment near the battery. Refer to the appli- cable “Engine Compartment” illustration in this section. This center contains cartridge fuses and mini-fuses. A label that identifies each component may be printed or embossed on the inside of the cover.
Page 589 MAINTAINING YOUR VEHICLE 587 Cartridge Mini- CAUTION! Cavity Description Fuse Fuse • When installing the Totally Integrated Power 40 Amp — Power Folding Seat Module cover, it is important to ensure the cover is Green properly positioned and fully latched. Failure to 30 Amp —...
Page 590 588 MAINTAINING YOUR VEHICLE Cartridge Mini- Cartridge Mini- Cavity Description Cavity Description Fuse Fuse Fuse Fuse 40 Amp — Power Memory 40 Amp — Rear Window Green Seat – If Equipped Green Defogger 40 Amp — Partial Zero Emis- 40 Amp —...
Page 591 MAINTAINING YOUR VEHICLE 589 Cartridge Mini- Cartridge Mini- Cavity Description Cavity Description Fuse Fuse Fuse Fuse — 15 Amp Rear Center Brake — 20 Amp Power Outlet #1 Blue Lamp/Brake Switch Yellow (ACC), Rain Sensor, Cigar Lighter (Instru- — 20 Amp Trailer Lighting, Front ment Panel or with Yellow...
Page 592 590 MAINTAINING YOUR VEHICLE Cartridge Mini- Cartridge Mini- Cavity Description Cavity Description Fuse Fuse Fuse Fuse — 15 Amp Ignition Off Draw — — 20 Amp Trailer Tow – If Blue Video System, Satel- Yellow Equipped lite Radio, DVD, — 20 Amp Rear View Mirror, Hands-Free Module,...
Page 593 MAINTAINING YOUR VEHICLE 591 Cartridge Mini- Cartridge Mini- Cavity Description Cavity Description Fuse Fuse Fuse Fuse — 25 Amp Powertrain — 20 Amp Fuel Pump, Diesel Natural Yellow Lift Pump – If Equipped — 15 Amp Instrument Cluster Blue Interior Light, Switch —...
Page 594 592 MAINTAINING YOUR VEHICLE Cartridge Mini- Cartridge Mini- Cavity Description Cavity Description Fuse Fuse Fuse Fuse — 10 Amp Airbag Module, — 20 Amp Power Outlet #3 (In- THATCHUM – If Yellow strument Panel or Equipped with Console Center) — 10 Amp Powertrain —...
Page 595: Vehicle Storage
MAINTAINING YOUR VEHICLE 593 steering column. If you experience temporary or perma- REPLACEMENT BULBS nent loss of these systems, see your authorized dealer for service. LIGHT BULBS – Interior Bulb Number Center & Rear Dome Lamp ....578 VEHICLE STORAGE Center &...
Page 596: Bulb Replacement
594 MAINTAINING YOUR VEHICLE headlamp switch off and the key removed. Because of LIGHT BULBS – Exterior Bulb Number this, you should not attempt to service a headlamp bulb Headlamp – (Low and High Beam Halogen) ..H11 yourself.
Page 597: Quad Headlamps
MAINTAINING YOUR VEHICLE 595 Quad Headlamps 5. Reconnect the wiring connector to the bulb. 1. Raise the hood to access the high or low beam bulbs at Front Park/Turn Signal Lamp the rear of the headlamp housing. 1. Raise the hood to access the rear of the headlamp 2.
Page 598: Front Side Marker Lamp
596 MAINTAINING YOUR VEHICLE Front Side Marker Lamp Fog Lamp 1. Raise the hood to access the rear of the headlamp NOTE: Access to the fog lamp bulb is from the rear of housing. the fascia. On the left rear side of the fascia, remove the push pin and lower the hinged access door on the air NOTE: Access is somewhat limited.
Page 599: Rear Tail, Stop, Turn Signal, Side Marker And Backup Lamp
MAINTAINING YOUR VEHICLE 597 3. Reconnect the wiring harness to the new bulb and reinstall the bulb by twisting clockwise. Rear Tail, Stop, Turn Signal, Side Marker And Backup Lamp 1. Raise the liftgate. 2. Remove the tail lamp assembly by removing the two screws from the inboard side.
Page 600: Center High-Mounted Stop Lamp (Chmsl)
598 MAINTAINING YOUR VEHICLE 3. Twist the socket and remove it from the lamp assem- License Lamp bly. The license plate lamp is located under the tailgate light bar and above the license plate. 4. Pull the bulb to remove it from the socket. 1.
Page 601: Fluid Capacities
MAINTAINING YOUR VEHICLE 599 FLUID CAPACITIES U.S. Metric Fuel (Approximate) 20 Gallons 76 Liters Engine Oil with Filter 3.6L Engine (SAE 5W-30, API Certified) 6 Quarts 5.6 Liters Cooling System * 3.6L Engine (MOPAR Engine Coolant/Antifreeze 5 13.4 Quarts 12.6 Liters Year/100,000 Mile Formula or equivalent) * Includes heater and coolant recovery bottle filled to MAX level.
Page 602: Fluids, Lubricants And Genuine Parts
(Hybrid Organic Additive Technology) or equivalent. Use API Certified SAE 5W-30 Engine Oil, meeting the requirements of Engine Oil Chrysler Material Standard MS-6395. Refer to your oil filler cap for cor- rect SAE grade. Engine Oil Filter MOPAR Engine Oil Filter or equivalent.
Page 603: Chassis
MAINTAINING YOUR VEHICLE 601 Chassis Component Fluid, Lubricant, or Genuine Part MOPAR ATF+4 Automatic Transmission Fluid or equivalent licensed Automatic Transmission ATF+4 product. MOPAR DOT 3 and SAE J1703 should be used or equivalent. If DOT 3 Brake Master Cylinder brake fluid is not available, then DOT 4 is acceptable.
Page 605 MAINTENANCE SCHEDULES CONTENTS Maintenance Schedule ....604 ▫ Required Maintenance Intervals ..606...
Page 606 604 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE On Non-EVIC equipped vehicles, “Change Oil” will flash The Scheduled Maintenance services listed in this in the instrument cluster odometer and a single chime manual must be done at the times or mileages specified will sound, indicating that an oil change is necessary. to protect your vehicle warranty and ensure the best Based on engine operation conditions, the oil change vehicle performance and reliability.
Page 607 MAINTENANCE SCHEDULES 605 NOTE: “Understanding Your Instrument Panel” or under “In- • The oil change indicator message will not monitor the strument Cluster Description/Odometer/Trip Odom- time since the last oil change. Change your vehicle’s eter” in “Understanding Your Instrument Panel” for oil if it has been six months since your last oil change, further information.
Page 608 606 MAINTENANCE SCHEDULES Once A Month At Each Oil Change • Check tire pressure and look for unusual wear or • Change the engine oil filter. damage. • Inspect the brake hoses and lines. • Inspect the battery and clean and tighten the terminals •...
Page 609 MAINTENANCE SCHEDULES 607 8,000 Miles (13,000 km) or 16,000 Miles (26,000 km) or 12 Months Maintenance Service 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 610: Service Schedule
608 MAINTENANCE SCHEDULES 24,000 Miles (39,000 km) or 32,000 Miles (52,000 km) or 24 Months Maintenance Service 18 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 611 MAINTENANCE SCHEDULES 609 40,000 Miles (65,000 km) or 48,000 Miles (78,000 km) or 36 Months Maintenance Service 30 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 612 610 MAINTENANCE SCHEDULES 56,000 Miles (91,000 km) or 64,000 Miles (104,000 km) or 48 Months Maintenance Service 42 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 613 MAINTENANCE SCHEDULES 611 72,000 Miles (117,000 km) or 80,000 Miles (130,000 km) or 60 Months Maintenance Service 54 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 614 612 MAINTENANCE SCHEDULES 88,000 Miles (143,000 km) or 96,000 Miles (156,000 km) or 72 Months Maintenance Service 66 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 615 MAINTENANCE SCHEDULES 613 104,000 Miles (169,000 km) or 112,000 Miles (182,000 km) or 84 Months Maintenance Service 78 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 616 614 MAINTENANCE SCHEDULES 120,000 Miles (195,000 km) or 128,000 Miles (208,000 km) or 96 Months Maintenance Service 90 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 617 MAINTENANCE SCHEDULES 615 136,000 Miles (221,000 km) or 144,000 Miles (234,000 km) or 108 Months Maintenance Service 102 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 618 616 MAINTENANCE SCHEDULES 152,000 Miles (247,000 km) or 114 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 152,000 miles (247 000 km). Odometer Reading Date Repair Order #...
Page 619 MAINTENANCE SCHEDULES 617 WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
Page 621: If You Need Consumer Assistance
Reporting Safety Defects ....624 ▫ Chrysler Group LLC Customer Center ..622 ▫ In The 50 United States And Washington, D.C.
Page 622 620 IF YOU NEED CONSUMER ASSISTANCE ▫ Traction Grades ..... 627 Department Of Transportation Uniform Tire Quality Grades ......627 ▫...
Page 623: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 621 SUGGESTIONS FOR OBTAINING SERVICE FOR the service advisor and list the items in order of priority. YOUR VEHICLE At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the...
Page 624: Chrysler Group Llc Customer Center
622 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized Chrysler Group LLC Customer Center dealer’s service manager first. Most matters can be re- P.O. Box 21–8004 solved with this process. Auburn Hills, MI 48321–8004 Phone: (800) 247–9753...
Page 625: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
IF YOU NEED CONSUMER ASSISTANCE 623 Customer Assistance For The Hearing Or Speech the manufacturer’s service contracts. If you purchased a Impaired (TDD/TTY) manufacturer’s service contract, you will receive Plan To assist customers who have hearing difficulties, the Provisions and an Owner Identification Card in the mail manufacturer has installed special TDD (Telecommuni- within three weeks of the vehicle delivery date.
Page 626: Warranty Information
See the Warranty Information Booklet, located on the has also made a major investment in facilities, tools, and DVD, for the terms and provisions of Chrysler Group training to assure that you are absolutely delighted with LLC warranties applicable to this vehicle and market.
Page 627: In Canada
IF YOU NEED CONSUMER ASSISTANCE 625 If NHTSA receives similar complaints, it may open an In Canada investigation, and if it finds that a safety defect exists in If you believe that your vehicle has a safety defect, you a group of vehicles, it may order a recall and remedy should contact the Customer Service Department imme- campaign.
Page 628 Chrysler Group LLC ve- maintaining, servicing, and repairing Chrysler Group hicles. Included are starting, operating, emergency LLC vehicles. A complete working knowledge of the...
Page 629 IF YOU NEED CONSUMER ASSISTANCE 627 DEPARTMENT OF TRANSPORTATION UNIFORM significantly from the norm due to variations in driving TIRE QUALITY GRADES habits, service practices, and differences in road charac- The following tire grading categories were established by teristics and climate. the National Highway Traffic Safety Administration.
Page 630 628 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat The temperature grade for this tire is established for and its ability to dissipate heat, when tested under a tire that is properly inflated and not overloaded.
Page 631 INDEX...
Page 632 630 INDEX Adding Engine Coolant (Antifreeze) ..572 Airbag Maintenance ..... . . 87 Adding Fuel .
Page 633 INDEX 631 Automatic Headlights ....205 Blind Spot Monitoring ....121 Automatic Temperature Control (ATC) .
Page 634 632 INDEX Caps, Filler Checks, Safety ......104 Fuel ......499 Child Restraint .
Page 635 INDEX 633 Connector Pressure Cap ......573 UCI ......352 Radiator Cap .
Page 636 634 INDEX Disposal Electronic Speed Control (Cruise Control) ..217 Antifreeze (Engine Coolant) ... . . 573 Electronic Stability Control (ESC) ... . . 454 Engine Oil .
Page 637 INDEX 635 Exhaust Gas Caution ... . . 57,104,494 Exhaust System ..... . 104,562 Fails to Start .
Page 638 636 INDEX Fuel Requirements ....495,496 Fuel ....... . . 491 Maintenance .
Page 639 INDEX 637 Fuel Saver ......314 Glass Cleaning ......584 Fuel, Flexible .
Page 640 638 INDEX Heater, Engine Block ..... 431 Instrument Panel Cover ....582 High Beam/Low Beam Select (Dimmer) Switch .
Page 641 INDEX 639 Lane Change Assist ..... . 208 Brake Warning ..... . 298 Lap/Shoulder Belts .
Page 642 640 INDEX Malfunction Indicator (Check Engine) ..295 Warning (Instrument Cluster Description) . . . 290 Oil Pressure ......301 Load Leveling System .
Page 643 INDEX 641 Map/Reading Lights ..... 233 MTBE/ETBE ......492 Memory Feature (Memory Seat) .
Page 644 642 INDEX Materials Added to ....560 Phone, Cellular ......129 Recommendation .
Page 645 INDEX 643 Radial Ply Tires ......473 Removable Floor Console ....269 Radiator Cap (Coolant Pressure Cap) .
Page 646: Bags
644 INDEX Schedule, Maintenance ....604 Reclining ......171 Seat Belt Maintenance .
Page 647 INDEX 645 Sliding Door ......46 Wheel, Tilt ......214 Slippery Surfaces, Driving On .
Page 648 646 INDEX Temperature Gauge, Engine Coolant ..300,522 Load Capacity ....466,467 Tether Anchor, Child Restraint ....94 Pressure Monitor System (TPMS) .
Page 649: Vehicle
INDEX 647 Weight ......509 Transmitter, Garage Door Opener (HomeLink®) . . 236 Towing Assistance .
Page 650 648 INDEX Vehicle Identification Number (VIN) ... . 6 Water Vehicle Loading ....467,501,503 Driving Through .
Page 651 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.
Page 652 Chrysler Group LLC 5th Edition Printed in U.S.A. 12Y531-126-AE...

This manual is also suitable for:

2012 town & country

Chrysler Town & Country 2012 Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

Chapters

Related Manuals for Chrysler Town & Country 2012

Summary of Contents for Chrysler Town & Country 2012