Page 1 Town & Country 2 0 1 0 OWNE R ’ S MANUAL...
Page 2: Table Of Contents
TABLE OF CONTENTS SECTION PAGE ............3 INTRODUCTION .
Page 4 INTRODUCTION CONTENTS Introduction ......4 Vehicle Identification Number ....6 How To Use This Manual .
Page 5: Introduction
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized Congratulations on selecting your new Chrysler Group dealer knows your vehicle best, has factory-trained tech- LLC vehicle. Be assured that it represents precision nicians and genuine MOPAR parts, and cares about workmanship, distinctive styling, and high quality - all your satisfaction.
Page 6 INTRODUCTION 5...
Page 7: Warnings And Cautions
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
Page 8: Vehicle Modifications/Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Remote Starting System — If Equipped ..27 ▫...
Page 11 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Seat Belts And Pregnant Women ..66 Sliding Side Door ..... . 41 ▫...
Page 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Transporting Passengers ....99 Rear Seat Delete Feature (Commercial Vehicles Only) — If Equipped..... 95 ▫...
Page 13: A Word About Your Keys
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Wireless Ignition Node (WIN) with integral ignition switch.
Page 14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead.
Page 15: Sentry Key
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Power window switches will also remain active Key-In-Ignition Reminder for up to 90 seconds after the ignition switch has been Opening the driver’s door when the Key Fob is in the turned to LOCK, depending upon the accessory delay ignition and the ignition switch position is LOCK or setting.
Page 16: Replacement Keys
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 vehicle can be used to start and operate the vehicle. The NOTE: The Sentry Key Immobilizer system is not system will shut the engine off in two seconds if an compatible with aftermarket remote starting systems. invalid Key Fob is used to start the engine.
Page 17: Vehicle Security Alarm - If Equipped
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • This device may not cause harmful interference. At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN). • This device must accept any interference that may be Keep the PIN in a secure location.
Page 18: Rearming Of The System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 After the alarm is set, the Vehicle Security Light will flash Rearming Of The System The Vehicle Security Alarm will rearm itself after the 15 at a slower rate to indicate that the Vehicle Security additional minutes of headlights and Vehicle Security Alarm is armed.
Page 19: Illuminated Entry - If Equipped
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE disarm the Vehicle Security Alarm. If someone enters Tamper Alert the vehicle through the liftgate and opens any door the If something has triggered the Vehicle Security Alarm in alarm will sound. your absence, the horn will sound three times when you unlock the doors and the Vehicle Security Light will flash •...
Page 20: Remote Keyless Entry (Rke) - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: Inserting the Key Fob with RKE transmitter into NOTE: • The front courtesy overhead console and liftgate lights the ignition switch disables all buttons on that RKE do not turn on if the dimmer control is in the interior transmitter;...
Page 21: Using The Rke Transmitter
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Using the RKE Transmitter (optional), power sliding doors, Remote Start feature Three-button RKE transmitters will provide basic UN- (optional). Some features can be programmed to the LOCK, LOCK and PANIC functions. customers preferences. For example, flash headlights or sound horn on LOCK.
Page 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 1. Perform this operation while standing outside the Remote Unlock Doors and Liftgate Press and release the UNLOCK button on the RKE vehicle. transmitter once to unlock the driver’s side or twice to 2.
Page 23 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Security Alarm activated will cause the alarm to sound. Sound Horn with Remote Lock Press the UNLOCK button to deactivate the Vehicle This feature will cause the horn to chirp when the doors Security Alarm.
Page 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 2. Press the LOCK button on a programmed RKE trans- Using the Panic Alarm mitter for at least 4 seconds, but no longer than 10 sec- To turn the Panic Alarm feature on or off, press and hold onds.
Page 25 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the liftgate is locked and is not equipped with a Power Open/Close Right Power Sliding Door — If powered liftgate, pressing the LIFTGATE button twice Equipped will result in the liftgate becoming unlocked for 30 sec- Press the RIGHT Power Sliding Door button twice on the onds allowing you to manually access the liftgate area.
Page 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 • For vehicles not equipped with the EVIC, perform the NOTE: Pressing the LOCK button on the RKE transmit- following steps: ter while you are in the vehicle will activate the Vehicle Security Alarm.
Page 27 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Programming Additional Transmitters 2. Remove and replace the battery. Avoid touching the If you do not have a programmed RKE transmitter, new battery with your fingers. Skin oils may cause contact your authorized dealer for details. battery deterioration.
Page 28: Remote Starting System - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 • Doors closed 1. A weak battery in the RKE transmitter. The expected life of the battery is approximately three years. • Hood closed 2. Closeness to a radio transmitter such as a radio station •...
Page 29 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE programmed). Then, the engine will start and the vehicle WARNING! will remain in the Remote Start mode for a 15-minute • Do not start or run an engine in a closed garage or cycle.
Page 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 • For vehicles equipped with the Electronic Vehicle To Enter the Vehicle After Remote Start To enter the vehicle while the engine is running during a Information Center (EVIC), the message “Insert Key/ Remote Start, you must first unlock the vehicle using the Turn to ON”...
Page 31: Door Locks
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Turn Off the Engine While in Remote Start a valid Key Fob into the ignition switch and rotating the Mode Key Fob to the ON position, and then rotating the Key Press and release the REMOTE START button one time or Fob back to the LOCK/OFF position.
Page 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Manual Door Lock Sliding Door Lock If the lock plunger is rearward when you shut either side WARNING! sliding door, the door will lock. Make sure the keys are • For personal security and safety in the event of an not inside the vehicle before closing the door.
Page 33: Power Door Locks - If Equipped
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • When leaving the vehicle, always remove the key from the ignition switch, and lock your vehicle. Do not leave unattended children in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe per- sonal injuries and death.
Page 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 operate. A chime will sound if the Key Fob is in the If you press the power door lock switch while the sliding ignition switch and a door is open, as a reminder to door is open, the sliding door will lock.
Page 35 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • On vehicles not equipped with the optional EVIC 8. If a chime is not heard, the program mode was perform the following steps: canceled before the feature could be disabled. If neces- sary, repeat the previous procedure.
Page 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 The Unlock Doors Automatically On Exit feature will not 4. Within 15-seconds, cycle the ignition Key Fob from the operate if there is any manual operation of the power LOCK position to the ON/RUN position a minimum of door locks (lock or unlock).
Page 37: Windows
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Use the Lock Doors Automatically at 15 mph (24 km/h) and Unlock Doors Automatically On Exit features in accordance with local laws. WINDOWS Power Vent Windows — If Equipped Switches on the driver’s door trim panel let the driver operate the two vent windows from the driver’s seat.
Page 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Power Window Lockout Switch — If Equipped The driver may lock out all power windows by depress- ing the bar switch just below the power window switches. Driver’s Power Window Switches 1 – Left Rear 3 –...
Page 39 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front Passenger Power Window Switch There is a single switch on the front passenger’s door trim panel which operates the passenger door window and locks and unlocks all doors. The switch will operate only when the ignition switch is in the ON or ACC position and during power accessory delay.
Page 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Sliding Side Door Power Window Switch — If Equipped Second row passengers may open and close the sliding door window by a single switch on the door handle assembly. The switches will operate only when the ignition switch is in the ON or ACC position and during power acces- sory delay.
Page 41 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto-Down Feature — If Equipped To stop the window from going all the way up during the The front window switches may be equipped with an Auto Up operation, push down on the switch briefly. Auto-Down feature.
Page 42: Things To Know Before Starting Your Vehicle 41
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Wind Buffeting WARNING! Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the There is no anti-pinch protection when the window ears. Your vehicle may exhibit wind buffeting with the is almost closed.
Page 43: Power Sliding Side Door - If Equipped
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To keep your door operating properly, observe the fol- NOTE: The left side sliding door cannot be opened lowing guidelines: while the fuel door is open. This feature operates only when the sliding door is fully closed prior to opening the •...
Page 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 There are power sliding side door switches located on the trim panel just in front of the power sliding door for the rear seat passengers and in the overhead console for the driver and passengers.
Page 45 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To avoid unintentional operation of the power sliding door switch is pressed. To close the door, wait until it doors from the rear seats, press the power sliding door is fully open and then press the switch again. master lock button, located in the overhead console, to •...
Page 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 The Sliding Side Door Open Flash can be enabled or When the power sliding door master lock switch is in the ON position, the power sliding side door may not be disabled by performing the following procedure: opened or closed by pressing the switch located on the 1.
Page 47: Sliding Side Door Child Protection Lock
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Sliding Side Door Child Protection Lock To provide a safer environment for small children riding in the rear seats, the sliding doors are equipped with a Child Protection Door Lock system. NOTE: When the Child Protection Door Lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position.
Page 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 • When the Child Protection Door Lock system is en- WARNING! gaged, (even if the inside door lock is in the unlocked position) the door can be opened only by using the Avoid trapping anyone in the vehicle in a collision.
Page 49: Liftgate
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: To open the liftgate, press the liftgate release handle • After setting the Child Protection Door Lock system, located on the underside of the license plate bar and pull always test the door from the inside to make certain it the liftgate open with one fluid motion.
Page 50: Power Liftgate - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 transmitter will result in the liftgate becoming unlocked for 30 seconds allowing you to manually access the liftgate area. Power Liftgate — If Equipped The power liftgate may be opened manually or by using the button on the Remote Keyless Entry (RKE) transmit- ter.
Page 51 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The power liftgate may be closed by pressing the button, When the RKE transmitter button is pressed and the located in the upper left trim in the liftgate opening. Flash Lights feature is enabled, the tail lights will flash to Pushing once will only close the liftgate.
Page 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 • There are also pinch sensors attached to the side of the (62°C). Be sure to remove any buildup of snow or ice liftgate opening. Light pressure anywhere along these from the liftgate before pressing any of the power strips will cause the liftgate to return to the open liftgate buttons.
Page 53: Occupant Restraints
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Supplemental Side Airbag Inflatable Curtains (SABIC) Gas props support the liftgate in the open position. However, because the gas pressure drops with tempera- that span the front, second, and third row seating for ture, it may be necessary to assist the props when the driver and passengers seated next to a window —...
Page 54: Lap/Shoulder Belts
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 NOTE: The Advanced Front Airbags have a multistage and cause a collision that includes you. This can happen inflator design. This allows the airbag to have different far away from home or on your own street. rates of inflation based on severity and type of collision.
Page 55 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Wearing your belt in the wrong place could make • It is extremely dangerous to ride in a cargo area, your injuries in a collision much worse. You might inside or outside of a vehicle.
Page 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 2. The seat belt latch plate is near the seatback of the WARNING! front seats and next to your arm in the rear seats. Grasp • A belt that is worn under your arm is very danger- the latch plate and pull out the belt.
Page 57 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch WARNING! plate into the buckle until you hear a “click”. • A belt that is buckled into the wrong buckle will not protect you properly.
Page 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen.
Page 59 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE is long enough to fit, insert the large latch plate into the WARNING! buckle until you hear a “click.” The retractor should withdraw any slack in the belt. A frayed or torn belt could rip apart in a collision and leave you with no protection.
Page 60: Automatic Locking Retractors (Alr) Mode - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Automatic Locking Retractors (ALR) Mode — If Equipped In this mode, the shoulder belt is automatically pre- locked. The belt will still retract to remove any slack in the shoulder belt. The Automatic Locking Mode is avail- able on all passenger-seating positions with a combina- tion lap/shoulder belt.
Page 61: Seat Belt Pretensioners - If Equipped
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Allow the belt to retract. As the belt retracts, you will NOTE: These devices are not a substitute for proper seat hear a clicking sound. This indicates the safety belt is belt placement by the occupant.
Page 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 How the Active Head Restraints (AHR) Work The Occupant Restraint Controller (ORC) determines whether the severity or type of rear impact require the Active Head Restraints (AHR) to deploy. In case of AHR deployment both driver and front passenger seat AHR’s will be deployed.
Page 63 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Grasp the deployed AHR from the rear seat. CAUTION! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of an accident.
Page 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. 3 — Final Downward Movement To Engage Locking Mecha- nism 1 — Downward Movement 2 —...
Page 65: Enhanced Seat Belt Use Reminder System (Beltalert )
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For safety reasons, have the Active Head Restraints 4. The AHR front soft foam and trim half should lock into the back decorative plastic half. checked by a qualified specialist at an authorized dealer.
Page 66 60 seconds of the ignition switch being turned to the ON 4. Turn the ignition switch to the LOCK position. A or START position. Chrysler Group LLC does not recom- single chime will sound to signify that you have success- mend deactivating BeltAlert .
Page 67: Seat Belts And Pregnant Women
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belts and Pregnant Women WARNING! We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is Using a seat belt extender when not needed can the best way to keep the baby safe.
Page 68: Airbag System Components
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 The Advanced Front Airbags have a multistage inflator design. This allows the airbag to have different rates of inflation based on the severity and type of collision. This vehicle may also be equipped with Supplemental Side Airbag Inflatable Curtains (SABIC) to protect the driver, front, and rear passengers sitting next to a win- dow.
Page 69: Advanced Front Airbag Features
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Front Passenger Airbag determined by the Occupant Restraint Controller (ORC), which may receive information from the impact sensors • Supplemental Rear Impact Active Head Restraint for at the front of the car. Driver and Front Passenger —...
Page 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 is marked with an airbag label sewn into the outboard WARNING! (Continued) side of the seat. • Do not put anything on or around the airbag covers or attempt to open them manually. You may damage the airbags and you could be injured because the airbags may no longer be functional.
Page 71 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Side Airbag Inflatable Curtain The system includes sensors adjacent to both front and (SABIC) — If Equipped rear seat occupants that are calibrated to deploy the SABIC airbags offer side-impact and vehicle rollover SABIC airbags during impacts that require airbag occu- protection to front and rear seat outboard occupants in pant protection.
Page 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Knee Impact Bolsters WARNING! The Knee Impact Bolsters help protect the knees of the driver and the front passenger, and position everyone for Infants in rear-facing child restraints should NEVER the best interaction with the Advanced Front Airbag. ride in the front seat of a vehicle with a passenger front airbag.
Page 73 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE You should read the instructions provided with your WARNING! child restraint to make sure that you are using it properly. • Relying on the airbags alone could lead to more All occupants should ALWAYS wear their lap and shoul- severe injuries in a collision.
Page 74: Airbag Deployment Sensors And Controls
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 The Advanced Front Airbags will not deploy in all frontal Airbag Deployment Sensors and Controls collisions, including some that may produce substantial Occupant Restraint Controller (ORC) vehicle damage — for example, some pole collisions, The ORC is part of a Federally regulated safety system truck underrides, and angle offset collisions.
Page 75 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC monitors the readiness of the electronic parts of It also includes diagnostics that will illuminate the instru- the system whenever the ignition switch is in the START ment cluster Airbag Warning Light if a malfunction is or ON position.
Page 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 the Advanced Front Airbags. Different airbag inflation The ORC determines if a side collision requires the side rates are possible, based on the collision type and sever- airbags to inflate based on the severity and type of ity.
Page 77 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Side Airbag Inflatable Curtain where the side curtain airbag inflates. This especially (SABIC) Inflator Units — If Equipped applies to children. The side curtain airbag is only about During collisions where the impact is confined to a 3-1/2 in (9 cm) thick when it is inflated.
Page 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 NOTE: Front and/or side airbags will not deploy in all Enhanced Accident Response System In the event of an impact causing airbag deployment, if collisions. This does not mean something is wrong with the communication network remains intact, and the the airbag system.
Page 79 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE airbag inflation. These airborne particles may irritate Maintaining Your Airbag System the skin, eyes, nose, or throat. If you have skin or eye WARNING! irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air.
Page 80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Airbag Warning Light WARNING! (Continued) You will want to have the airbags ready to • Do not attempt to modify any part of your ad- inflate for your protection in a collision. While vanced airbag system.
Page 81: Event Data Recorder (Edr)
In the event of an accident, your vehicle is designed to used by Chrysler Group LLC and others to learn more record up to five seconds of specific vehicle data param- about the possible causes of crashes and associated...
Page 82 Confidential • Engine RPM data will not be disclosed by Chrysler Group LLC to any • Brake switch status third party except when: • Pedal position 1.
Page 83: Integrated Child Booster Seat - If Equipped
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Integrated Child Booster Seat — If Equipped The Integrated Child Booster Seat (if equipped) is located in each second-row passenger seat. The booster seat is designed for children weighing between 48 and 85 lbs (22 and 39 kg) and between 47 in (119 cm) and 57 in (145 cm) tall.
Page 84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 WARNING! (Continued) • The swivel seat should be locked in the forward- facing position when using the booster seat with the vehicle in motion. • Be certain that the seat cushion is locked securely into position before using the seat.
Page 85: Integrated Child Seat - If Equipped
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Once the seat belt is long enough to fit properly, insert Integrated Child Seat — If Equipped the latch plate into the buckle until you hear a “click.” Operating instructions for the second row bench seat with Integrated Child Seat are included with the seat.
Page 86: Child Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 To obtain Integrated Child Seat replacement instruc- WARNING! tions: Refer to “Publication Order Forms” in If You Need Consumer Assistance and specify publication number In a collision, an unrestrained child, even a tiny baby, 81–016–8050 when ordering.
Page 87 86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Safety experts recommend that children ride WARNING! rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types Rearward-facing child seats must NEVER be used in of child restraints can be used rearward-facing: infant the front seat of a vehicle with a front passenger carriers and convertible child seats.
Page 88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 vehicle by the lap/shoulder belt or the LATCH child WARNING! restraint anchorage system. Refer to “Lower Anchors and Tether for CHildren (LATCH)”. Never place any child seat, booster seat, or infant carrier in the Swivel ’n Go seat while it is in the An aftermarket belt-positioning booster seat is for chil- rearward-facing position.
Page 89 88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The lap portion should be low on the hips and as snug WARNING! as possible. • Improper installation can lead to failure of an • Check belt fit periodically. A child’s squirming or infant or child restraint.
Page 90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 shoulder portion of the lap/shoulder belt will tighten Here are some tips on getting the most out of your child restraint: the belt. The cinching latch plate will keep the belt tight; however, any seat belt system will loosen with •...
Page 91 90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Buckle the child into the seat according to the child installed as described here. Again, carefully follow the restraint manufacturer’s directions. installation instructions that are provided with the child restraint system. •...
Page 92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 third row fold-in-floor seats are equipped with a child WARNING! restraint tether anchor at the center seating position. Improper installation of a child restraint to the NOTE: LATCH anchorages can lead to failure of an infant or •...
Page 93 92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If your child restraint seat is not LATCH-compatible, 4. Tighten the lower attachment strap while firmly push- install the restraint using the vehicle seat belts. ing the child restraint rearward and downward into the vehicle seat.
Page 94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 Installing the Top Tether Strap (with either Lower Anchors or Vehicle Seat Belt): 1. Route the top tether strap under the adjustable head restraint between the steel posts. 2. Provide enough slack (reference child restraint in- structions) for the tether strap to reach the tether anchor located near the bottom of the seat back.
Page 95 94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE then allow the belt to retract into the retractor. For WARNING! additional information on ALR, refer to “Automatic Locking Mode”. An incorrectly anchored tether strap could lead to increased head motion and possible injury to the To install a child restraint, first, pull enough of the seat child.
Page 96: Rear Seat Delete Feature (Commercial Vehicles Only) - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 Transporting Pets WARNING! Airbags deploying in the front seat could harm your pet. An unrestrained pet could be thrown about and possibly NEVER carry a child in a rear facing infant carrier in injured, or injure a passenger during panic braking or in a vehicle without rear seats.
Page 97: Restraining Infants And Small Children With Seat Delete Feature (Commercial Vehicles Only)
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The rearward-facing infant carrier is for babies weigh- This vehicle is equipped with a child restraint tether anchor located on the lower rear of the front passenger ing up to about 20 lbs (9 kg), and less than one year seat.
Page 98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 • Children more than 40 lbs (18 kg) should be secured in 3. Route the tether strap under the head rest. the passenger seat in a child restraint or belt- NOTE: Ensure that the child restraint tether strap is positioning booster seat with the seat adjusted to the centered between the headrest supports underneath the rear most position.
Page 99: Engine Break-In Recommendations
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE While cruising, brief full-throttle acceleration within the WARNING! limits of local traffic laws, contributes to a good break-in. Wide-open throttle acceleration in low gear can be detri- The vehicle tether anchor is designed to be used with mental and should be avoided.
Page 100: Safety Tips
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 SAFETY TIPS Exhaust Gas Transporting Passengers WARNING! NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. WARNING! Breathing it can make you unconscious and can eventually poison you.
Page 101: Safety Checks You Should Make Inside The Vehicle
100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you are required to drive with the liftgate open, make Safety Checks You Should Make Inside the sure that all windows are closed and the climate control Vehicle BLOWER switch is set at high speed. DO NOT use the Seat Belts recirculation mode.
Page 102: Periodic Safety Checks You Should Make Outside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 Defroster Lights Check operation by selecting the defrost mode and place Have someone observe the operation of exterior lights the blower control on high speed. You should be able to while you work the controls. Check turn signal and high feel the air directed against the windshield.
Page 104: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS ▫ Tilt Mirrors In Reverse (Available With Mirrors ......108 Memory Seat Only) —...
Page 105 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Third Row Power Recline — If Equipped . . . 144 Seats ......122 ▫...
Page 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 ▫ Daytime Running Lights (Canada/Fleet Electronic Speed Control — If Equipped ..168 Vehicles Only) ..... . 159 ▫...
Page 107 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Cleaning Parksense ▫ Troubleshooting Tips ....193 ....178 ▫...
Page 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 ▫ Driver Seatback Storage — If Equipped ..205 Console Features ..... . 210 ▫...
Page 109: Mirrors
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror — If Equipped A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).
Page 110: Automatic Dimming Mirror - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Automatic Dimming Mirror — If Equipped CAUTION! When using this feature the mirror will automatically adjust for headlight glare from vehicles behind you. You To avoid damage to the mirror during cleaning, never can turn the feature on or off by pressing the button at the spray any cleaning solution directly onto the mirror.
Page 111: Driver's Automatic Dimming Mirror - If Equipped
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror Folding Feature WARNING! All outside mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have Vehicles and other objects seen in an outside convex three detent positions: full forward, full rearward and mirror will look smaller and farther away than they normal.
Page 112: Heated Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Refer to “Driver Memory Seat” in “Understanding the Features of Your Vehicle” for further information. Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster.
Page 113: Illuminated Vanity Mirrors - If Equipped
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE when the vehicle is shifted out of REVERSE position. Each stored memory setting will have an associated Tilt Mirrors in Reverse position. NOTE: The Tilt Mirrors in Reverse feature is not en- abled when delivered from the factory. The Tilt Mirrors in Reverse feature can be enabled or disabled in the Elec- tronic Vehicle Information Center (EVIC).
Page 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 The BSM detection zone covers approximately one lane on both sides of the vehicle (11 ft or 3.35 m). The zone starts at the outside rear view mirror and extends ap- proximately 20 ft (6 m) to the rear of the vehicle. The BSM system monitors the detection zones on both sides of the vehicle when the vehicle speed has reached approxi- mately 6 mph (10 km/h) or higher and will alert the...
Page 115 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE beyond the side of your vehicle, this may result in the BSM warning light remaining illuminated the entire time the vehicle is in a forward gear. The area on the rear fascia where the radar sensors are located must remain free of snow, ice, and dirt/road contamination so that the BSM system can function properly.
Page 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 The BSM system notifies the driver of objects in the The BSM system can also be configured to sound an detection zones by illuminating the BSM warning light audible (chime) alert and mute the radio to notify the located in the outside mirrors.
Page 117 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Entering From The Side Entering From The Rear Vehicles that move into your adjacent lanes from either Vehicles that come up from behind your vehicle on either side of the vehicle. side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h).
Page 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Overtaking Traffic If you pass another vehicle slowly (with a relative speed less than 10 mph (16 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 10 mph (16 km/h), the warning light will not illuminate.
Page 119 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The BSM system is designed not to issue an alert on The BSM system will not alert you of objects that are stationary objects such as guardrails, posts, walls, foliage, traveling in the opposite direction of the vehicle in berms, etc.
Page 120: Rear Cross Path
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 WARNING! The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones. The BSM system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicles mirrors, glance over your shoulder, and use your turn signal before changing lanes.
Page 121: Modes Of Operation
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In a parking lot situation, oncoming vehicles can Modes Of Operation be obscured by vehicles parked on either side. If the Three selectable modes of operation are available in the sensors are blocked by other structures or vehicles, the Electronic Vehicle Information Center (EVIC).
Page 122: Uconnect™ Phone - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 signal is then activated, and it corresponds to an alert Blind Spot Alert Off present on that side of the vehicle, an audible chime will When the BSM system is turned off there will be no also be sounded.
Page 123: Seats
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Seats are a primary part of the Occupant Restraint System of the vehicle. They need to be used properly for safe operation of the vehicle. WARNING! • DO NOT allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Page 124: Manual Reclining Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
Page 125: Manual Lumbar Adjust Lever - If Equipped
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! DO NOT ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or fatally injured. Use the recliner only when the vehicle is parked.
Page 126: Eight-Way Power Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
Page 127: Heated Seats - If Equipped
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped WARNING! This feature heats the front driver and passenger seats. The controls for front heated seats are located on the Adjusting a seat while the vehicle is moving is center instrument panel area.
Page 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion or other physical condition must exercise care when using the seat heater.
Page 129: Adjusting Head Restraints
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Repeated overheating of the seat could damage the heating element and/or degrade the material of the seat. Adjusting Head Restraints Head restraints can reduce the risk of injury in the event of a rear impact. The head restraint should be adjusted so the top of the head restraint is located above the top of your ear.
Page 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head. Push Button Active Head Restraint — If Equipped For comfort the Active Head Restraints can be tilted forward and backward.
Page 131 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • In the event of deployment of an Active Head Re- straint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in “Things to Know Before Starting Your Vehicle” for further information. WARNING! • Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision.
Page 132: Stow 'N Go Seating - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Stow ’n Go Seating — If Equipped WARNING! (Continued) On vehicles equipped with Stow ’n Go seating, the • Do not place items over the top of the Active Head second and third row seats may be folded into the floor Restraint, such as coats, seat covers or portable for convenient storage.
Page 133 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Slide the storage bin locking mechanism to the 4. Pull up on the seatback recliner lever located on the LOCK position and then pull up on the storage bin latch outboard side of the seat and fold the seatback down. To to open the cover.
Page 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 5. Pull rearward on the release strap located at the rear of CAUTION! the seat and tumble the seat forward into the storage bin. The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.
Page 135: Easy Access Seating
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Pull up on the handle to lift the seat out of the storage bin and push the seat rearward to latch the seat anchors. Second Row Seatback Release Lever 4. Adjust the head restraint to the desired position, close the storage bin cover and slide the storage bin locking Second Row Seat Release Handle mechanism to the Unlocked position.
Page 136: Swivel 'N Go™ Premium Seating - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 To tilt the seat, pull forward on the release strap located WARNING! on the front of the seat between the seatback and seat cushion and tilt the seat fully forward. In the event of a collision you could be injured if the seat is not fully latched.
Page 137 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Seats are removable WARNING! When the seatback release handle is lifted, the seat- back will rotate forward. To avoid injury, if you are not seated in the seat, stay clear from the area in the path of the rotating seatback.
Page 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 WARNING! Failure to comply with the following conditions could result in serious injury or even death: • NEVER place any child seat or infant carrier in the Swivel ’n Go™ seat while it is in the rearward facing position.
Page 139 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Removing Swivel ’n Go™ Premium Seating — If Equipped 1. Remove any obstructions from the floor behind the seat, and stow the third row seat. 2. Pull up on the release bar located at the bottom front edge of the swivel seat.
Page 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 5. Lower the release handle located at the bottom front Swivel ’n Go™ Premium Seating Table — If edge of the seat. Equipped The Swivel ’n Go™ Seating Table consists of an easily Each seat weighs about 90 lbs (41 kg).
Page 141 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The table and leg are stored beneath the floor when not in 3. Swivel the second row seats so they are facing the rear. use. To install the table follow these steps: 4. Insert pole into base by aligning the lock button into 1.
Page 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 NOTE: You will hear an audible “click” when the lock WARNING! (Continued) button engages the base. • DO NOT place heavy or sharp objects on table. 6. Place the table top over the installed pole aligning •...
Page 143 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To separate the table top from the pole, follow these 3. While pulling on the latch, pull upward to remove the steps: table top from the pole. 1. Locate the release latch on the underside of the table NOTE: The table top should be removed from the leg top.
Page 144: Second Row Bench Seat - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Plastic Grocery Bag Retainer Hooks Retainer hooks which will hold plastic grocery bag handles are built into the seatbacks of all rear seats and some front seats. The floor supports the partial weight of the bagged goods.
Page 145: Third Row Power Recline - If Equipped
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If not properly latched, the bench seats could become loose. Personal injuries could result. After reinstall- ing these seats, be sure the red indicator button on the release handles return into the handles. Third Row Power Recline —...
Page 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Rear Panel Power Switch Bank One Touch Folding Seat Third Row The rear switch bank allows multiple power folding and 1 — Open to Normal 4 — Fold Flat 2 — Stow 5 — Right/Left Seats unfolding positions for the third row seats.
Page 147 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: 2. Pull release strap marked “1” located on the rear of the • Disconnect the center shoulder belt from the small seat to lower the seatback. buckle and lower the head restraints before attempting 3.
Page 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 To Unfold Third Row Seats Tailgate Mode 1. Pull up on the assist strap to lift the seat out of the 1. Pull release strap “2”, then pull release strap “3” to storage bin and push the seat forward until the anchors rotate the entire seat rearward.
Page 149: Driver Memory Seat - If Equipped
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! To avoid serious injury or death, NEVER operate the vehicle with occupants in the third row seat while in the tailgate mode. DRIVER MEMORY SEAT — IF EQUIPPED The Memory Buttons 1 and 2 on the driver’s door panel can be programmed to recall the driver’s seat, driver’s outside mirror, adjustable brake and accelerator pedals, and radio station preset settings.
Page 150: Setting Memory Positions And Linking Rke
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 5. Turn on the radio and set the radio station presets (up Setting Memory Positions and Linking RKE Transmitter to Memory to 10 AM and 10 FM stations can be set). NOTE: Each time the SET (S) button and a numbered 6.
Page 151 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE to “Electronic Vehicle Information Center (EVIC)/ To recall the memory setting for driver two, press Customer-Programmable Features” in “Understanding MEMORY button 2 on the driver’s door or the UNLOCK Your Instrument Panel” for further information. button on the RKE transmitter linked to Memory Position 12.
Page 152: Easy Entry/Exit Seat (Available With Memory Seat Only)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 3. Press and release the memory SET (S) button located Customer-Programmable Features in “Understanding on the driver’s door. A chime will sound signaling that Your Instrument Panel” for further information. you are in the memory set mode. Easy Entry/Exit Seat (Available with Memory Seat 4.
Page 153: To Open And Close The Hood
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When you remove the key from the ignition switch the NOTE: The Easy Entry/Easy Exit feature can be en- driver seat will move to a position 0.3 in (7.7 mm) abled or disabled through the programmable features in forward of the rear stop if the driver seat position is the Electronic Vehicle Information Center (EVIC).
Page 154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Hood Release Safety Catch Location 2. Move to the front of the vehicle and look inside the Use the hood prop rod to secure the hood in the open center of the hood opening. Locate, then push the safety position.
Page 155: Lights
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS CAUTION! All of the lights, except the Hazard Warning lights, headlight high beams and flash-to-pass, are controlled by To prevent possible damage, do not slam the hood to switches to the left of the steering column on the instru- close it.
Page 156: Interior Lighting
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Interior Lighting Dome Light Positions Interior lights are turned on when a door or liftgate is Rotate the dimmer control completely opened, the Remote Keyless Entry (RKE) transmitter is upward to the second detent (extreme activated, or when the dimmer control is moved to the top position) to turn on the interior extreme top.
Page 157: Parking Lights
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Parade Mode (Daytime Brightness Feature) Halo Lights — If Equipped Rotate the dimmer control to the first Halo lights are strategically placed soft lighting that help detent. This feature brightens the to illuminate specific areas to aid the occupants in odometer, radio and overhead dis- locating specific features while driving at night.
Page 158: Automatic Headlights - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 To change the brightness of the instrument panel lights, rotate the dimmer control up or down. Automatic Headlights — If Equipped This system automatically turns your headlights on or off based on ambient light levels. To turn the system on, turn the headlight switch to the extreme counterclockwise position aligning the indicator with the “A”...
Page 159: Headlights On With Wipers - If Equipped
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights On With Wipers — If Equipped When exiting the vehicle the driver can choose to have When your headlights are in the Automatic mode and the the headlights remain on for 30, 60, or 90 seconds or not engine is running, the headlights will automatically turn remain on.
Page 160: Daytime Running Lights (Canada/Fleet Vehicles Only)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Lights-On Reminder Front Fog Lights — If Equipped If the headlights or the parking lights are left on, or if the To activate the front fog lights, turn on the parking dimmer control is in the extreme top position after the lights or the low beam headlights and push in the ignition switch is turned OFF, a chime will sound when headlight switch control knob.
Page 161: Multifunction Lever
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The battery protection feature will be disabled if the ignition switch is turned to any other position other than LOCK during the three minute delay. Multifunction Lever The multifunction lever is located on the left side of the steering column.
Page 162: High/Low Beam Switch
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Lane Change Assist Flash-To-Pass Tap the lever up or down once, without moving beyond You can signal another vehicle with your headlights by the detent, and the turn signal (right or left) will flash lightly pulling the multifunction lever toward you.
Page 163: Windshield Wipers And Washers
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Rotate the headlight switch counterclockwise to the NOTE: Broken, muddy or obstructed headlights and AUTO (A) position. taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). 3.
Page 164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 cause the washers to spray for a maximum of 10 seconds, or until the multifunction lever is released, and the wipers will cycle three times. NOTE: • If the multifunction lever is pressed while in the delay range, the wipers will operate for several seconds after the multifunction lever is released, and then resume the intermittent interval previously selected.
Page 165: Rain Sensing Wipers - If Equipped
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE seconds, to a maximum of 20 seconds between cycles. WARNING! The time delay will be doubled if the vehicle speed is less than 10 mph (16 km/h). Sudden loss of visibility through the windshield could lead to an accident.
Page 166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 calibrated for best overall wiping sensitivity. If the opera- (Customer-Programmable Features)” in “Understand- tor desires more wiping sensitivity, they may select ing Your Instrument Panel” for further information. sensitivity positions 4 or 5. If the operator desires less The Rain Sensing system has protective features for the wiping sensitivity, they may select sensitivity positions 2 wiper blades and arms.
Page 167: Tilt Steering Column
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the wiper control on the multifunction lever is moved down, as desired. Pull the lever upward to the locked or the shift lever is moved out of the NEUTRAL position to lock the steering column firmly in place. position.
Page 168: Adjustable Pedals - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle.
Page 169: Electronic Speed Control - If Equipped
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The pedals cannot be adjusted when the vehicle is in WARNING! REVERSE or when the Electronic Speed Control Sys- tem is on. The following messages will be displayed Do not adjust the pedals while the vehicle is moving. on vehicles equipped with the Electronic Vehicle In- You could lose control and have an accident.
Page 170: To Activate
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 simultaneously. If this occurs, the Electronic Speed Con- trol System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push the ON/OFF button (located in the end of the lever) once, and the cruise indicator light (located in the mes- sage window of the odometer) will illuminate, showing that the Electronic Speed Control system is on.
Page 171: To Set At A Desired Speed
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE speed memory. Pushing the ON/OFF button to the OFF WARNING! position or turning OFF the ignition erases the set speed memory. Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidently Resuming Speed set the system or cause it to go faster than you want.
Page 172: Accelerating To Pass
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 increase. Each time the lever is tapped speed increases, so Accelerating To Pass tapping the lever three times will increase speed by Press the accelerator as you normally would. When the 3 mph (4.8 km/h), etc. pedal is released, the vehicle will return to the set speed.
Page 173: Parksense Rear Park Assist - If Equipped
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense will remember the last system state (enabled WARNING! or disabled) from the last ignition cycle when the ignition is changed to the RUN/ON position. Electronic Speed Control can be dangerous where the system cannot maintain a constant speed.
Page 174: Parksense Warning Display
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 ParkSense Warning Display The ParkSense Warning screen will only be displayed if Sound and Display is selected from the Customer- Programmable Features section of the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer- Programmable Features)”...
Page 175: Parksense Display
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense Display When the vehicle is in REVERSE, the warning display will turn ON indicating the system status. Park Assist Disabled Park Assist ON...
Page 176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 The system will indicate a detected obstacle by showing three solid arcs and will produce a ⁄ second tone. As the vehicle moves closer to the object the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.
Page 177 176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone. The following chart shows the warning display operation when the system is detecting an obstacle: Continuous Tone...
Page 178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 WARNING DISPLAY DISTANCES DISPLAY MESSAGE OBSTACLE DISTANCE FROM: ARC’s AUDIBLE SIGNAL REAR CORNERS REAR CENTER Park Assist ON None None Warning Object Detected 78.7 in (200 cm) 3 Solid Yes, 1/2 second Warning Object Detected 39.3 in (100 cm) 3 Flashing Slow Tone...
Page 179: Enabling/Disabling Parksense
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Enabling/Disabling ParkSense ignition cycle, and it will display the “SERVICE PARK You can turn ParkSense ON or OFF through the EVIC. ASSIST SYSTEM” message. Refer to “Electronic Vehicle The available choices are: OFF, Sound Only, or Sound and Information Center (EVIC)”...
Page 180: Parksense System Usage Precautions
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 • ParkSense , when on, will MUTE the radio when it is ParkSense System Usage Precautions sounding a tone. NOTE: • Ensure that the rear bumper is free of dirt and debris • If a ParkSense system malfunction occurs, a single to keep the ParkSense Rear Park Assist system oper- chime will sound once per ignition cycle.
Page 181 180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Objects must not be within 12 in (30 cm) from the rear CAUTION! (Continued) fascia/bumper while driving the vehicle. Failure to do • The vehicle must be driven slowly when using so can result in the system misinterpreting a close ParkSense to be able to stop in time when the object as a sensor problem, causing the “SERVICE obstacle is detected.
Page 182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 WARNING! WARNING! (Continued) • Before using the ParkSense Rear Park Assist • Drivers must be careful when backing up even system, it is strongly recommended that the ball when using the ParkSense Rear Park Assist sys- mount and hitch ball assembly is disconnected tem.
Page 183: Parkview Rear Back Up Camera - If Equipped
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKVIEW REAR BACK UP CAMERA — IF WARNING! EQUIPPED Your vehicle may be equipped with the ParkView Rear Drivers must be careful when backing up even when Back Up Camera that allows you to see an on-screen using the ParkView Rear Back Up Camera.
Page 184: Turning Parkview On Or Off - With Navigation/Multimedia Radio
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 4. Enable or disable the rear camera feature by selecting CAUTION! (Continued) “enable rear camera in reverse” soft key. • To avoid vehicle damage, the vehicle must be 5. Press the “save” soft key. driven slowly when using ParkView to be able to stop in time when an obstacle is seen.
Page 185: Overhead Consoles
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. When the vehicle is shifted into REVERSE, an image of NOTE: Premium sunroof console models include all of the rear of the vehicle will appear with a caution note to above except sunglass storage. “check entire surroundings”...
Page 186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 Courtesy/Interior Lighting Sunglass Storage (non-sunroof only) At the forward end of the console are two courtesy lights At the rear of the front overhead console, a compartment (standard dome light has two buttons). The lights turn on is provided for the storage of two pairs of sunglasses.
Page 187 186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Overhead Consoles — If Equipped The rear overhead storage system is available in two versions: with or without sunroof. An additional LED at the front of the rear console shines down on the front foot-well area while in courtesy mode, for added convenience.
Page 188: Garage Door Opener - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Rear Courtesy/Reading Lights — If Equipped Rear Console Halo Lighting The overhead console has two sets of courtesy lights. The The rear overhead console has recessed halo lighting lights turn on when a front door, a sliding door or the around the perimeter of the console base.
Page 189 188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink buttons that are located in the headliner WARNING! or sun visor designate the three different HomeLink • Your motorized door or gate will open and close channels. while you are training the universal transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate.
Page 190: Programming Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 Place the handheld transmitter 1 to 3 in (3 to 8 cm) away Programming HomeLink from the HomeLink button you wish to program while Before You Begin keeping the indicator light in view. If you have not trained any of the HomeLink buttons, erase all channels before you begin training.
Page 191 190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After training a HomeLink channel, if the garage This can usually be found where the hanging antenna door does not operate with HomeLink and the ga- wire is attached to the garage door opener motor. It is rage door opener was manufactured after 1995, the NOT the button normally used to open and close the garage door opener may have a rolling code.
Page 192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 6. Firmly press and release the LEARN or TRAINING Using HomeLink button. The name and color of the button may vary by To operate, press and release the programmed manufacturer. HomeLink button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, NOTE: You have 30 seconds in which to initiate the next security system, entry door lock, home/office lighting,...
Page 193: Gate Operator/Canadian Programming
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Gate Operator/Canadian Programming successfully accepted the frequency signal. The indica- Canadian radio frequency laws require transmitter sig- tor light will flash slowly and then rapidly when fully nals to time-out (or quit) after several seconds of trans- trained.
Page 194: Troubleshooting Tips
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 2. This device must accept any interference that may be Troubleshooting Tips If you are having trouble programming HomeLink , here received including interference that may cause undesired are some of the most common solutions: operation.
Page 195: Power Sunroof Operation
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Sunroof Operation Closing the Sunroof Manually To close the sunroof from an open or vent position, press Opening the Sunroof Manually and hold the switch forward. The sunroof will close fully Press the switch rearward and hold, and the sunroof will and stop automatically.
Page 196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 Express Close WARNING! Press the switch forward and release, and the sunroof will close automatically from any position. The sunroof Never leave children in a vehicle with the key in the will close fully, then stop automatically. This is called ignition switch.
Page 197: Electrical Power Outlets - If Equipped
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Auto-Express with Anti-Pinch Protection with the sunroof open, adjust the sunroof opening to During express closing, anytime an obstacle that restricts minimize the buffeting or open any window. glass movement is detected, the motor will stop and Sunroof Maintenance reverse travel to avoid pinching the object.
Page 198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 • Do not exceed the maximum power of 160 Watts (13 One outlet in the removable floor console shares a fuse Amps) at 12 Volts. If the 160 Watt (13 Amp) power with the lower outlet in the instrument panel and is also rating is exceeded the fuse protecting the system will connected to the battery.
Page 199 198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Many accessories that can be plugged in draw To avoid serious injury or death: • Only devices designed for use in this type of power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
Page 200: Power Inverter - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 inverter should automatically reset. If the power rating CAUTION! (Continued) exceeds approximately 170 Watts, the power inverter • Power outlets are designed for accessory plugs may have to be reset manually. To reset the inverter only.
Page 201: Cupholders
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The power inverter switch is located near the center of CUPHOLDERS the instrument panel below the two 12 Volt power There are nine cupholders in the interior. Two cupholders outlets. in the center front instrument panel, four in the floor consoles and three more are located in the third row To turn on the power outlet, press the switch once.
Page 202: Instrument Panel Cupholders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 Pull the drawer out firmly until it stops, and place the Instrument Panel Cupholders The instrument panel cupholders are located in a pull-out container to be held in either one of the cupholder wells. drawer just above the lower storage bin.
Page 203: Smoker's Package Kit - If Equipped
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Two outboard mesh pockets are on intermediate seating. WARNING! The mesh pockets are flexible enough to hold juice boxes, toys, games or MP3 players, etc. If containers of hot liquid are placed in the bottle holder, they can spill when the door is closed, burn- Smoker’s Package Kit —...
Page 204: Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 STORAGE Glove Compartments Upper Glove Compartment To open the upper compartment, press inward on the release button (2). The door will spring open about 1 in (2.54 cm). Manually lift the front edge of the door upward, until fully opened, and the detent is engaged.
Page 205: Door Trim Panel Storage
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Door Trim Panel Storage WARNING! Front Door Storage If containers of hot liquid are placed in the bottle Both interior front door panels have multiple pockets for holder, they can spill when the door is closed, burn- storage.
Page 206: Driver Seatback Storage - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 Driver Seatback Storage — If Equipped Umbrella Holder The drivers seatback has a primary storage pocket on all An umbrella holder has been conveniently molded into models and an optional secondary mesh pocket. the left front door entry scuff molding.
Page 207: Second Row Floor Storage Bins
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Second Row Floor Storage Bins CAUTION! The area below the floor covers, located in front of the second row seats, is available for storage. The storage bin cover must lay flat and be locked to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.
Page 208: Storage Bin Safety Warning
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 Storage Bin Safety Warning WARNING! (Continued) Carefully follow these warnings to help prevent personal • Do not drive the vehicle with the storage bin injury or damage to your vehicle: covers open. Keep the storage bin covers closed and latched while the vehicle is in motion.
Page 209: Center And Rear Overhead Console Storage - If Equipped
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Seat Storage Bin Cover Emergency Release Lever NOTE: In the event of an individual being locked inside As a security measure, your vehicle may be built with a the storage bin, the storage bin cover can be opened from Storage Bin Cover Emergency Release is built into the inside of the bin by pushing on the glow-in-the-dark storage bin cover latching mechanism.
Page 210: Coat Hooks
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 Coat Hooks Coat hooks are located along the headliner for the second and third row seating positions. The coat hook load limit is 10 lbs (4.5 kg). Exceeding the recommended load limit can cause the coat hooks to break or disengage from the vehicle.
Page 211: Cargo Area Storage
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Area Storage NOTE: With all rear seats stowed or removed, 4 x 8 foot The liftgate sill plate has a raised line with the statement sheets of building material will fit on the vehicle floor “Load To This Line”.
Page 212: Premium Console - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 • The basic console is removable from the vehicle for 4. Reinstall the clip first and then while pushing down- additional floor space by removing the cap and clip at ward on the console with slight pressure, reinstall the the console base.
Page 213 212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Top tray storage • Upper storage bin can hold nine regular or 18 thin CDs or other items • Large console center storage will store headphones for the available rear DVD entertainment system or other items •...
Page 214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 holder insert for both cavities can easily be removed for Position 2 shows the raised storage tray revealing a large cleaning. The cupholders will also accommodate large storage area below. size cups and 20 oz (.6 L) bottles. Position 1 shows the console closed with four cupholders and a convenient storage tray.
Page 215 214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dual Storage Bins Position 4 shows the complete console in its rearmost Position 3 shows the top portion of the console in a position. Again, lifting second latch handle at the front of rearward position.
Page 216: Rear Window Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 5. Pull up on the console to be sure it is firmly latched. To Remove The Premium Floor Console 1. Pull up on the bottom release handle in the front of the WARNING! console.
Page 217: Load-Leveling System
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: CAUTION! (Continued) • You can turn off the heated mirror feature at anytime • Do not use scrapers, sharp instruments, or abra- by pressing the rear window defroster switch a second sive window cleaners on the interior surface of the time.
Page 218: Roof Luggage Rack - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and side rails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars.
Page 219 218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: To help control wind noise when installing the CAUTION! (Continued) crossbars ensure the embossed arrow is facing the front • To avoid damage to the roof rack and vehicle, do of the vehicle. When the crossbars are not in use, the front not exceed the maximum roof rack load capacity of crossbar should be fastened just forward of the middle 150 lbs (68 kg).
Page 220: Sun Screens - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 WARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in per- sonal injury or property damage. Follow the Roof Rack Cautions when carrying cargo on your roof rack.
Page 221 220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Gently pull up on the tab to raise the sun screen. Continue pulling the sun screen until the tab is near the top of the window. Sun Screen Extended To lower the sun screen, gently lift the tab upward to disengage the hooks, and feed the screen back into the base sill.
Page 222 UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS ▫ Electronic Vehicle Information Center (EVIC) Instrument Panel Features ....225 Displays ......247 Instrument Cluster .
Page 223 222 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operating Instructions — Voice Command Media Center 130 (RES/RSC) — AM/FM System (VR) — If Equipped ... . . 258 Stereo Radio With CD Player (MP3 AUX Jack) And Sirius Radio .
Page 224 UNDERSTANDING YOUR INSTRUMENT PANEL 223 ▫ Play Mode ......285 ▫ Operating Instructions - Uconnect™ phone (If Equipped) .
Page 225 224 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Summer Operation ....314 Climate Controls ..... . 297 ▫...
Page 226: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 225 INSTRUMENT PANEL FEATURES 1 — Air Vents 5 — Analog Clock 9 — DVD – If Equipped 13 — Switch Bank 2 — Instrument Cluster 6 — Upper Glove Compartment 10 — Cup Holders 14 — Ignition Switch 3 —...
Page 227: Instrument Cluster
226 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER...
Page 228: Instrument Cluster Descriptions
UNDERSTANDING YOUR INSTRUMENT PANEL 227 vehicle has completely stopped and the shift lever is INSTRUMENT CLUSTER DESCRIPTIONS placed in the PARK position, the light should turn off. 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when If the light remains lit with the engine running, your the ignition switch is in the ON position.
Page 229 228 UNDERSTANDING YOUR INSTRUMENT PANEL vehicle is experiencing a problem with the charging As an added safety feature, your vehicle has been system. Obtain SERVICE IMMEDIATELY. See an autho- equipped with a Tire Pressure Monitoring System rized dealer. (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated.
Page 230 UNDERSTANDING YOUR INSTRUMENT PANEL 229 Your vehicle has also been equipped with a TPMS CAUTION! malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is The TPMS has been optimized for the original combined with the low tire pressure telltale. When the equipment tires and wheels.
Page 231 230 UNDERSTANDING YOUR INSTRUMENT PANEL vehicle and shut off the engine as soon as possible. A shift the transmission into NEUTRAL and idle the ve- chime will sound for four minutes when this light turns hicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service.
Page 232 UNDERSTANDING YOUR INSTRUMENT PANEL 231 10. Electronic Stability Program (ESP) Indicator Light WARNING! / Brake Assist System (BAS) Warning Light The malfunction light for the Electronic Stabil- If a warning light remains on the system may not be ity Program (ESP) is combined with Brake working and you will not have the benefit of ESP or Assist System (BAS).
Page 233 232 UNDERSTANDING YOUR INSTRUMENT PANEL If the light remains on when the parking brake has been NOTE: The light may flash momentarily during sharp disengaged, and the fluid level is at the full mark on the cornering maneuvers, which change fluid level condi- master cylinder reservoir, it indicates a possible brake tions.
Page 234 UNDERSTANDING YOUR INSTRUMENT PANEL 233 Operation of the Brake Warning Light can be checked by 13. Anti-Lock Brake (ABS) Light turning the ignition switch from the OFF position to the This light monitors the Anti-Lock Brake System ON position. The light should illuminate for approxi- (ABS).
Page 235 234 UNDERSTANDING YOUR INSTRUMENT PANEL 14. Electronic Stability Program (ESP) Indicator Light 17. Front Fog Light Indicator — If Equipped / Traction Control System (TCS) Indicator Light This indicator will illuminate when the front fog If this indicator light flashes during accelera- lights are on.
Page 236 UNDERSTANDING YOUR INSTRUMENT PANEL 235 the ON position, before engine start. If the bulb does not WARNING! come on when turning the key from OFF to ON, have the condition checked promptly. A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal Certain conditions such as a loose or missing gas cap, operating conditions.
Page 237 236 UNDERSTANDING YOUR INSTRUMENT PANEL 21. Temperature Gauge WARNING! The temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that A hot engine cooling system is dangerous. You or the engine cooling system is operating satisfactorily. others could be badly burned by steam or boiling coolant.
Page 238 UNDERSTANDING YOUR INSTRUMENT PANEL 237 NOTE: On the Base cluster, the reset button toggles 24. Message Display Area between odometer, Trip A, Trip B, ECO and outside When the appropriate conditions exist, the following temperature. To reset a message display on Base Cluster odometer messages will display: (gATE, gASCAP, noFUSE, CHangE OIL, LoCOOL, Lo- ECO .
Page 239 238 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Some of the above warnings will be displayed in LoW tirE the Compass Mini-Trip Computer / Electronic Vehicle When the appropriate condition exists, the odometer Information Center Display Area located in the instru- display will toggle between LoW and tirE for three ment cluster.
Page 240 UNDERSTANDING YOUR INSTRUMENT PANEL 239 damaged, a “noFUSE” message will display in the odom- instrument cluster. To reset the oil change indicator eter display area. For further information on fuses and system (after performing the scheduled maintenance), fuse locations refer to “Fuses” in “Maintaining Your perform the following steps.
Page 241 240 UNDERSTANDING YOUR INSTRUMENT PANEL U.S. Federal regulations require that upon transfer of 26. Compass Mini-Trip Computer (CMTC) or Electronic vehicle ownership, the seller certify to the purchaser the Vehicle Information Center (EVIC) Display — If correct mileage that the vehicle has been driven. If your Equipped odometer needs to be repaired or serviced, the repair Compass Mini-Trip Computer (CMTC) Display —...
Page 242: Compass Mini-Trip Computer (Cmtc) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 241 • If the vehicle is equipped with a Chrysler ™ gps 27. Compass Mini-Trip Computer (CMTC) Display Button (Navigation Radio), the NAV system will provide the Press the left reset button to scroll through sub-menus compass direction, and the variance and calibration (i.e., Outside Temperature, Trip Functions: AVG Fuel...
Page 243: Cmtc Reset Buttons
242 UNDERSTANDING YOUR INSTRUMENT PANEL CMTC Reset Buttons Should this wrench symbol display with the letter P next to it, your Park Assist System CMTC Reset Button needs servicing. Contact an authorized dealer. Press the left reset button located on the instrument cluster to scroll through sub menus (i.e., Trip Functions: CMTC Trip Odometer (ODO) / ECO (Fuel Saver AVG Fuel Economy, DTE, Elapsed Time, and Units).
Page 244: Compass/Temperature Display
UNDERSTANDING YOUR INSTRUMENT PANEL 243 • Magnetic and battery powered devices, (such as cell ECO (Fuel Saver Indicator) — If Equipped The ECO-ON indicator will illuminate when you are phones, iPod’s, radar detectors, PDA’s and laptops) driving in a fuel efficient manner and can be used to should be kept away from the top of the instrument modify driving habits in order to increase fuel economy.
Page 245 244 UNDERSTANDING YOUR INSTRUMENT PANEL To Set the Variance 1. Start the engine and leave the transmission in the Start the engine and leave the transmission gear selector PARK position. lever in the PARK position. Press and hold the CMTC 2.
Page 246: Electronic Vehicle Information Center (Evic) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 245 This system conveniently allows the driver to select a ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED variety of useful information by pressing the switches The Electronic Vehicle Information Center (EVIC) fea- mounted on the steering wheel. The EVIC consists of the tures a driver-interactive display that is located in the following: instrument cluster.
Page 247 246 UNDERSTANDING YOUR INSTRUMENT PANEL EVIC Menu / Step Control Button, as Steering Wheel EVIC Compass/Temp it appears on the left side of the steer- Control Button, as it appears on the ing wheel spoke. right side of the steering wheel spoke. Press and release the MENU button, and the Press and release the Compass/Temperature mode...
Page 248: Electronic Vehicle Information Center (Evic) Displays
UNDERSTANDING YOUR INSTRUMENT PANEL 247 • Check Gascap Electronic Vehicle Information Center (EVIC) Displays • Left Front Turn Signal Light Out When the appropriate conditions exist, the EVIC displays • Left Rear Turn Signal Light Out the following messages: • Door(s) Ajar (with a single chime, if vehicle is in •...
Page 249 248 UNDERSTANDING YOUR INSTRUMENT PANEL system is temporarily unavailable due to sensor block- after a single chime has sounded, to indicate the next age, electronic interference, or other temporary con- scheduled oil change interval. The engine oil change ditions. When this message is displayed both outside indicator system is duty-cycle based, which means the rear view icons will be illuminated.
Page 250: Trip Functions
UNDERSTANDING YOUR INSTRUMENT PANEL 249 NOTE: If the indicator message illuminates when you Distance To Empty (DTE) start the engine, the oil change indicator system did not Shows the estimated distance that can be traveled with reset. If necessary, repeat these steps. the fuel remaining in the tank.
Page 251: Compass Display / Eco (Fuel Saver Mode) - If Equipped
250 UNDERSTANDING YOUR INSTRUMENT PANEL Elapsed Time Compass Display / ECO (Fuel Saver Mode) — If Shows the total elapsed time of travel since the last reset Equipped when the ignition switch is in the ACC position. Elapsed The compass readings indicate the direc- time will increment when the ignition switch is in the ON tion the vehicle is facing.
Page 252 UNDERSTANDING YOUR INSTRUMENT PANEL 251 ECO (Fuel Saver Mode) — If Equipped Manual Compass Calibration The ECO message will display below the outside tem- If the compass appears erratic and the CAL indicator perature in the EVIC display. This message will appear does not appear in the EVIC display, you must put the whenever you are driving in a fuel efficient manner.
Page 253 252 UNDERSTANDING YOUR INSTRUMENT PANEL Compass Variance Compass Variance is the difference between Magnetic North and Geographic North. To compensate for the differences, the variance should be set for the zone where the vehicle is driven, per the zone map. Once properly set, the compass will automatically compensate for the differences, and provide the most accurate compass heading.
Page 254: Personal Settings (Customer-Programmable Features)
UNDERSTANDING YOUR INSTRUMENT PANEL 253 3. Press the STEP button until “Compass Variance” mes- Language sage, and the last variance zone number, displays in the When in this display you may select one of five lan- EVIC. guages for all display nomenclature, including the trip functions and the navigation system (if equipped).
Page 255 254 UNDERSTANDING YOUR INSTRUMENT PANEL NEUTRAL position and the driver’s door is opened. To this feature is not selected then the memory seat, mirror, make your selection, press and release the RESET button and radio settings can only return to the memory set until ON or OFF appears.
Page 256 UNDERSTANDING YOUR INSTRUMENT PANEL 255 video system (if equipped), power sunroof (if equipped), Easy Exit Seat This feature provides automatic driver seat positioning to and power outlets will remain active for up to 10 minutes enhance driver mobility when entering and exiting the after the ignition switch is turned OFF.
Page 257 256 UNDERSTANDING YOUR INSTRUMENT PANEL only show a visual alert in the outside mirrors. By system can be enabled with Sound Only, Sound and pressing and releasing the RESET button a second time Display, or turned OFF through the EVIC, to make your “Blind Spot Alert Lights/CHM”...
Page 258 UNDERSTANDING YOUR INSTRUMENT PANEL 257 until “ON” or “OFF” appears. Refer to “SmartBeam™” in Sound Horn with Remote Key Lock When ON is selected, a short horn sound will occur when “Understanding The Features Of Your Vehicle” for fur- the RKE transmitter LOCK button is pressed. This feature ther information.
Page 259: Media Center 730N/430 (Rer/Ren/Rbz)
258 UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 730N/430 (RER/REN/RBZ) — Operating Instructions — Uconnect™ Phone — If AM/FM STEREO RADIO AND CD/DVD/HDD/NAV — Equipped Refer to “Uconnect™ Phone” in the Uconnect™ User IF EQUIPPED Manual located on the DVD for further details. NOTE: The sales code is located on the lower right side of the unit’s faceplate.
Page 260 UNDERSTANDING YOUR INSTRUMENT PANEL 259 displayed. To move the minute backward, touch the Show Time if Radio is Off screen where the word “Min” with the arrow pointing When selected, this feature will display the time of day downward is displayed. on the touch screen when the radio is turned off.
Page 261: Clock Setting Procedure - Rer/Ren Radio
260 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Touch the screen where the words “Set Time Zone” are To Manually Set the Clock — RER/REN displayed. The time zone selection menu will appear on 1. Turn on the radio. the screen. 2. Touch the screen where the time is displayed. 4.
Page 262 UNDERSTANDING YOUR INSTRUMENT PANEL 261 6. To save the new time setting, touch the screen where Show Time if Radio is Off the word “Save” is displayed. When selected, this feature will display the time of day on the touch screen when the radio is turned off. Proceed Changing Daylight Savings Time as follows to change the current setting: When selected, this feature will display the time of day in...
Page 263: Media Center 130 (Res) - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack)
262 UNDERSTANDING YOUR INSTRUMENT PANEL Changing the Time Zone MEDIA CENTER 130 (RES) — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) 1. Turn on the radio. NOTE: The radio sales code is located on the lower right 2. Touch the screen where the time is displayed. side of the radio faceplate.
Page 264: Operating Instructions - Radio Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 263 Operating Instructions — Radio Mode SEEK Buttons Press and release the SEEK buttons to search for the next NOTE: The ignition switch must be in the ON or ACC listenable station in AM/FM mode. Press the right switch position to operate the radio.
Page 265 264 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Adjust the minutes using the right side TUNE/ Push the rotary TUNE/SCROLL control knob a second SCROLL control knob. Press the TUNE/SCROLL control time and MID will display. Turn the TUNE/SCROLL knob to save time change. control knob to the right or left to increase or decrease the mid-range tones.
Page 266 UNDERSTANDING YOUR INSTRUMENT PANEL 265 Push the rotary TUNE/SCROLL control knob again to SET 2 in both AM and FM. This allows a total of 12 AM exit setting tone, balance, and fade. and 12 FM stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by AM/FM Button pressing the pushbutton twice.
Page 267: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
266 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions — CD MODE For CD And If you insert a disc with the ignition ON and the radio MP3 Audio Play ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will NOTE: show the track number, and index time in minutes and •...
Page 268 UNDERSTANDING YOUR INSTRUMENT PANEL 267 the current selection. Pressing and holding the SEEK EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. button will allow faster scrolling through the tracks in CD and MP3 modes. TIME Button Press this button to change the display from a large CD If you have ejected a disc and have not removed it within...
Page 269: Notes On Playing Mp3 Files
268 UNDERSTANDING YOUR INSTRUMENT PANEL SET/RND Button (Random Play Button) Supported Medium Formats (File Systems) Press this button while the CD is playing to activate The medium formats supported by the radio are ISO 9660 Random Play. This feature plays the selections on the Level 1 and Level 2 and includes the Joliet extension.
Page 270 UNDERSTANDING YOUR INSTRUMENT PANEL 269 • Maximum number of characters in file/folder names: extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will • Level 1: 12 (including a separator . and a three- not play the file.
Page 271: Operation Instructions - Auxiliary Mode
270 UNDERSTANDING YOUR INSTRUMENT PANEL • Number of files and folders - Loading times will ID3 Tag information for artist, song title, and album title are supported for version 1 ID3 tags. ID3 version 2 is not increase with more files and folders supported by the radios.
Page 272: Media Center 130 (Res/Rsc) - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack) And Sirius Radio
UNDERSTANDING YOUR INSTRUMENT PANEL 271 not loud enough, turn the device’s volume up. If the AUX audio sounds distorted, turn the device’s volume down. TIME Button (Auxiliary Mode) Press this button to change the display to time of day. The time of day will display for five seconds (when ignition is OFF).
Page 273 272 UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch/Volume Control (Rotary) Voice Command System (Radio) — If Equipped Push the ON/VOLUME control knob to turn on the Refer to “Voice Command” in the Uconnect™ User radio. Push the ON/VOLUME control knob a second Manual located on the DVD for further details.
Page 274 UNDERSTANDING YOUR INSTRUMENT PANEL 273 If your vehicle is not equipped with or this feature is not 5. To exit, press any button/knob or wait five seconds. available on your vehicle, a “Not Equipped With The clock can also be set by pressing the SETUP button. Uconnect”...
Page 275 274 UNDERSTANDING YOUR INSTRUMENT PANEL TUNE Control SCROLL control knob to the right or left to adjust the Turn the rotary TUNE/SCROLL control knob clockwise sound level from the right or left side speakers. to increase or counterclockwise to decrease the frequency. Push the rotary TUNE/SCROLL control knob a fifth time Setting the Tone, Balance, and Fade and FADE will display.
Page 276 UNDERSTANDING YOUR INSTRUMENT PANEL 275 Toggle the MUSIC TYPE button to select the following 16-Digit Character Program Type format types: Display 16-Digit Character Personality Persnlty Program Type Display Public Public No program type Rhythm and Blues R & B None or undefined Religious Music Rel Musc...
Page 277 276 UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the Music Type icon the minutes using the right side TUNE/SCROLL is displayed, the radio will be tuned to the next frequency control knob. Press the TUNE/SCROLL control knob station with the same selected Music Type name.
Page 278: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
UNDERSTANDING YOUR INSTRUMENT PANEL 277 display window. Each button can be set for SET 1 and Operation Instructions — CD MODE for CD and SET 2 in both AM and FM. This allows a total of 12 AM MP3 Audio Play and 12 FM stations to be stored into pushbutton memory.
Page 279 278 UNDERSTANDING YOUR INSTRUMENT PANEL If you insert a disc with the ignition ON and the radio EJECT Button - Ejecting a CD ON, the unit will switch from radio to CD mode and Press the EJECT button to eject the CD. begin to play when you insert the disc.
Page 280: Notes On Playing Mp3 Files
UNDERSTANDING YOUR INSTRUMENT PANEL 279 the current selection. Pressing and holding the SEEK Press the right SEEK button to move to the next ran- button will allow faster scrolling through the tracks in domly selected track. CD and MP3 modes. Press the SET/RND button a second time to stop Ran- TIME Button dom Play.
Page 281 280 UNDERSTANDING YOUR INSTRUMENT PANEL • Level 2: 31 (including a separator . and a three- files properly and may be unable to play the file nor- mally. UDF and Apple HFS formats are not supported. character extension) The radio uses the following limits for file systems: Multisession disc formats are supported by the radio.
Page 282 UNDERSTANDING YOUR INSTRUMENT PANEL 281 rates (VBR) are also supported. The majority of MP3 files Playback of MP3 Files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or When a medium containing MP3 data is loaded, the VBR bit rates.
Page 283: List Button (Cd Mode For Mp3 Play)
282 UNDERSTANDING YOUR INSTRUMENT PANEL LIST Button (CD Mode for MP3 Play) Press and hold the INFO button again for three seconds Pressing the LIST button will bring up a list of all folders to return to elapsed time display. on the disc.
Page 284: Universal Consumer Interface (Uci) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 283 RER, RBZ, REN, REP, REW, RB2 or REZ touch-screen TIME Button (Auxiliary Mode) Press this button to change the display to time of day. The radio UCI feature, refer to the separate RER, REN, RBZ, time of day will display for five seconds (when the RB2 or REZ User’s Manual.
Page 285: Connecting The Ipod
284 UNDERSTANDING YOUR INSTRUMENT PANEL • Connecting an iPod to the AUX port located in the • If the iPod battery is completely discharged, it may radio faceplate, plays media, but does not use the UCI not communicate with the UCI system until a mini- feature to control the connected device.
Page 286: Controlling The Ipod Using Radio Buttons
UNDERSTANDING YOUR INSTRUMENT PANEL 285 jump to the previous track in the list. Turning this Controlling The iPod Using Radio Buttons To get into the UCI (iPod ) mode and access a connected button at any other time in the track, will jump to iPod , press the “AUX”...
Page 287: List Or Browse Mode
286 UNDERSTANDING YOUR INSTRUMENT PANEL beginning of the track. If you press the SEEK >> During Scan mode, you can also press the << SEEK button during play mode, it will jump to the next track and SEEK >> buttons to select the previous and next in the list.
Page 288 UNDERSTANDING YOUR INSTRUMENT PANEL 287 • Preset 5 – Audiobooks the track to be played highlighted on the radio display, press the TUNE control knob to select and • Preset 6 – Podcasts start playing the track. Turning the TUNE control •...
Page 289: Uconnect™ Multimedia (Satellite Radio) - If Equipped (Ren/Rer/Rbz/Res Radios Only)
288 UNDERSTANDING YOUR INSTRUMENT PANEL • MUSIC TYPE button: The MUSIC TYPE button is Uconnect™ Multimedia (SATELLITE RADIO) — IF another shortcut button to the genre listing on your EQUIPPED (REN/RER/RBZ/RES RADIOS ONLY) iPod . Satellite radio uses direct satellite-to-receiver broadcast- ing technology to provide clear digital sound, coast to CAUTION! coast.
Page 290: Electronic Serial Number/Sirius Identification Number (Esn/Sid)
UNDERSTANDING YOUR INSTRUMENT PANEL 289 information, call the toll-free number 888-539-7474, or Sirius ID number will display. The Sirius ID number visit the Sirius web site at www.sirius.com, or at www- display will time out in two minutes. Press any button on .siriuscanada.ca for Canadian residents.
Page 291: Reception Quality
290 UNDERSTANDING YOUR INSTRUMENT PANEL bikes should be placed as far rearward as possible, within Operating Instructions - Uconnect™ Multimedia the loading design of the rack. Do not place items directly (Satellite) Mode on or above the antenna. NOTE: The ignition switch must be in the ON or ACC Reception Quality position to operate the radio.
Page 292 UNDERSTANDING YOUR INSTRUMENT PANEL 291 INFO Button MUSIC TYPE Button Pressing the INFO button will cycle the display informa- Pressing this button once will turn on the Music Type tion between Artist, Song Title, and Composer (if avail- mode for five seconds. Pressing the MUSIC TYPE button able).
Page 293: Operating Instructions - Uconnect™ Phone (If Equipped)
292 UNDERSTANDING YOUR INSTRUMENT PANEL SETUP Button You may add a second channel to each pushbutton by Pressing the SETUP button allows you to select the repeating the above procedure with this exception: Press following items: the SET button twice and SET 2 will show in the display window.
Page 294: Uconnect™ Multimedia (Sirius Backseat Tv™) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 293 • One or two video screens Uconnect™ Multimedia (SIRIUS BACKSEAT TV™) — IF EQUIPPED • Third row swivel screen — If Equipped Satellite video uses direct satellite receiver broadcasting • Additional single-disc DVD player with two-screen technology to provide streaming video.
Page 295 294 UNDERSTANDING YOUR INSTRUMENT PANEL • Ten different medias to choose from in each screen (AM, FM, Sirius Radio, Sirius Backseat TV™, DVD1, DVD2, Hard Disc Drive (HDD), AUX in radio, AUX1, AUX2) The LCD screen(s) are located in the overhead compart- ment console.
Page 296: Remote Sound System Controls - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 295 The right-hand rocker switch has a pushbutton in the REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED center, and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume.
Page 297: Cd Player
296 UNDERSTANDING YOUR INSTRUMENT PANEL The button located in the center of the left-hand switch 1. Handle the disc by its edge; avoid touching the will tune to the next preset station that you have pro- surface. grammed in the radio preset pushbutton. 2.
Page 298: Radio Operation And Cellular Phones
UNDERSTANDING YOUR INSTRUMENT PANEL 297 oversized, or have protection encoding. Try a known Manual Heating and Air Conditioning System — If good disc before considering disc player service. Equipped The controls for the manual system in this vehicle contain RADIO OPERATION AND CELLULAR PHONES a series of outer rotary dials and inner push knobs.
Page 299 298 UNDERSTANDING YOUR INSTRUMENT PANEL Front Blower Control Temperature Control There are four blower speeds. Use this Use this control to regulate the tem- control to regulate the amount of air perature of the air inside the passenger forced through the system in any compartment.
Page 300 UNDERSTANDING YOUR INSTRUMENT PANEL 299 Mode Control (Air Direction) Bi-Level Mode Mode control allows you to choose Air is directed through the panel and floor outlets. from several selections of air distribu- tion. You can select either a primary NOTE: There is a difference in temperature (in any mode, as identified by the symbols, or conditions other than full cold or full hot), between the a blend of two of these modes.
Page 301 300 UNDERSTANDING YOUR INSTRUMENT PANEL Mix Mode Recirculation Control Air is directed through the floor, defrost and side Press this button to choose between outside air window demist outlets. This setting works best in intake or recirculation of the air inside the cold or snowy conditions that require extra heat at vehicle.
Page 302 UNDERSTANDING YOUR INSTRUMENT PANEL 301 • In cold or damp weather, the use of the RECIRCULA- Air Conditioning Operation TION mode will cause windows to fog on the inside Push on this button to engage the Air because of moisture buildup inside the vehicle. For Conditioning (A/C).
Page 303: Three-Zone Temperature Control - If Equipped
302 UNDERSTANDING YOUR INSTRUMENT PANEL Three-Zone Temperature Control — If Equipped With the Three-Zone Temperature Control System, each front seat occupant can independently control the Heat- ing, Ventilation, and Air Conditioning operations coming from the outlets on their side of the vehicle. Front Upper Three Zone Temperature Control 1 –...
Page 304 UNDERSTANDING YOUR INSTRUMENT PANEL 303 The Three-Zone Temperature Control bottom panel con- The primary control for the rear blower is on the front trols rear Heating, Ventilation, and Air Conditioning climate control unit located on the instrument panel. operations. When the front control is in any position other than rear, the front control operates all the rear functions.
Page 305: Rear Manual Climate Control - If Equipped
304 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: For vehicles equipped with Remote Start, the climate controls will not function during Remote Start operation if the blower control is left in the “O” (Off) position. Rear Manual Climate Control — If Equipped The Rear Manual Climate Control system has floor air outlets at the rear of the right side sliding door, and overhead outlets at each outboard rear seating position.
Page 306 UNDERSTANDING YOUR INSTRUMENT PANEL 305 Only when the front control for the rear blower is in the Rear Temperature Control RR position do the second row seat occupants have The rear mode selection RR, allows the settings to be control of the rear blower speed. controlled by the rear mode control knob.
Page 307: Automatic Temperature Control (Atc) - If Equipped
306 UNDERSTANDING YOUR INSTRUMENT PANEL • Occupants in the vehicle select AUTO mode operation Bi-Level Mode Air comes from both the headliner outlets and the by a button press on the right rotary knob and a floor outlets. comfort temperature setting using rotary knobs on the control unit.
Page 308 UNDERSTANDING YOUR INSTRUMENT PANEL 307 Front Upper ATC Panel Front Lower ATC Panel 1 - System On/Off 9 - Air Conditioning (A/C) On/Off 1 - Rear Blower Speed 4 - Rear ATC Lock 2 - Blower Indicator 10 - AUTO Mode / Blower 2 - Rear Temperature / Rear 5 - Rear DEFROST 3 - Left Front Temperature...
Page 309 308 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Operation NOTE: • It is not necessary to move the temperature settings for 1. Press the AUTO button on the Front Upper ATC Panel cold or hot vehicles. The system automatically adjusts and the word AUTO will illuminate in the front ATC the temperature, mode and fan speed to provide display, along with three temperatures for driver, front comfort as quickly as possible.
Page 310 UNDERSTANDING YOUR INSTRUMENT PANEL 309 Manual Operation Panel Mode This system offers a full complement of manual override Air is directed through the outlets in the instrument features. The AUTO symbol in the front ATC display will panel. These outlets can be adjusted for direction, be turned off when the system is being used in the and turned on or off to control airflow.
Page 311 310 UNDERSTANDING YOUR INSTRUMENT PANEL Floor Mode The SNOWFLAKE mode, or A/C button, allows Air comes from the floor outlets. A slight amount of the operator to manually activate or deactivate the air is directed through the defrost and side window air conditioning system.
Page 312 UNDERSTANDING YOUR INSTRUMENT PANEL 311 Recirculation Control Rear Automatic Temperature Control (ATC) — If When outside air contains smoke, odors, or Equipped high humidity, or if rapid cooling is desired, The Rear ATC System has floor air outlets at the rear of you may wish to recirculate interior air by the right side sliding door, and overhead outlets at each pressing the RECIRCULATION mode control...
Page 313 312 UNDERSTANDING YOUR INSTRUMENT PANEL The Rear ATC System is located in the headliner, near the 1. Press the REAR LOCK button on the front lower ATC center of the vehicle. panel. This turns off the REAR LOCK icon in the rear temperature knob.
Page 314 UNDERSTANDING YOUR INSTRUMENT PANEL 313 NOTE: CAUTION! • It is not necessary to move the temperature settings for cold or hot vehicles. The system automatically adjusts Interior air enters the Rear Automatic Temperature the temperature, mode and fan speed to provide Control System through an intake grille, located in comfort as quickly as possible.
Page 315: Summer Operation
314 UNDERSTANDING YOUR INSTRUMENT PANEL When rear controls are locked by the front system, the NOTE: In many temperature positions, the BI-LEVEL LOCK symbol on the temperature knob is illuminated mode is designed to provide cooler air out of the head- and any rear overhead adjustments are ignored.
Page 316: Winter Operation
UNDERSTANDING YOUR INSTRUMENT PANEL 315 Winter Operation Window Fogging To ensure the best possible heater and defroster perfor- Vehicle windows tend to fog on the inside in mild, rainy mance, make sure the engine cooling system is function- and/or humid weather. To clear the windows, select ing properly and the proper amount, type, and concen- DEFROST or MIX mode and increase the front blower tration of coolant is used.
Page 317: Operating Tips
316 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips A/C Air Filter— If Equipped On vehicles equipped with Automatic Temperature Con- trol (ATC), the climate control system filters out dust and pollen from the air. Refer to “Air Conditioning” in “Maintaining Your Vehicle” for filter replacement instructions.
Page 318: Starting And Operating
STARTING AND OPERATING CONTENTS ▫ Key Ignition Park Interlock ... . . 324 Starting Procedures ....321 ▫...
Page 319 318 STARTING AND OPERATING Driving Through Water ....332 Tire Safety Information ....344 ▫...
Page 320 STARTING AND OPERATING 319 ▫ Life Of Tire ......360 ▫ E85 Usage In Non-Flex Fuel Vehicles ..375 ▫...
Page 321 320 STARTING AND OPERATING ▫ Replacement Parts ....382 ▫ Vehicle Certification Label ....384 ▫...
Page 322: Starting Procedures
STARTING AND OPERATING 321 STARTING PROCEDURES Automatic Transaxle Before starting your vehicle, adjust your seat, adjust the The shift lever must be in the NEUTRAL or PARK inside and outside mirrors, fasten your seat belt, and if position before you can start the engine. Press the brake present, instruct all other occupants to buckle their seat pedal before shifting into any driving gear.
Page 323: Extreme Cold Weather (Below 20°F Or -29°C)
322 STARTING AND OPERATING NOTE: This vehicle is equipped with a transaxle shift WARNING! (Continued) interlocking system. The brake pedal must be pressed • Do not attempt to push or tow your vehicle to get to shift out of PARK. it started.
Page 324: After Starting
STARTING AND OPERATING 323 After Starting CAUTION! The idle speed will automatically decrease as the engine warms up. To prevent damage to the starter, DO NOT crank the engine for more than 15–second intervals at one time. ENGINE BLOCK HEATER — IF EQUIPPED Wait 10 to 15 seconds before trying again.
Page 325: Automatic Transaxle
324 STARTING AND OPERATING AUTOMATIC TRANSAXLE WARNING! CAUTION! It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle Damage to the transaxle may occur if the following speed. If your foot is not firmly on the brake pedal, precautions are not observed: the vehicle could accelerate quickly forward or in •...
Page 326: Brake/Transaxle Interlock System
STARTING AND OPERATING 325 This system prevents the key fob from being removed Brake/Transaxle Interlock System This vehicle is equipped with a Brake Transmission Shift unless the shift lever is in PARK. It also prevents moving Interlock System (BTSI) that holds the shift lever in the the shift lever out of PARK, unless the key fob is in the PARK position when the ignition switch is in the LOCK ACC/ON position, and the brake pedal is pressed.
Page 327: Transaxle
326 STARTING AND OPERATING The electronically-controlled transaxle provides a precise PARK shift schedule. The transaxle electronics are self- This range supplements the parking brake by locking the calibrating; therefore, the first few shifts on a new vehicle transaxle. The engine can be started in this gear. Never may be somewhat abrupt.
Page 328 STARTING AND OPERATING 327 The following indicators should be used to ensure that WARNING! you have placed the shift lever into the PARK position: • Never use the PARK position as a substitute for • When moving the shift lever into PARK, press the the parking brake.
Page 329 328 STARTING AND OPERATING REVERSE DRIVE — Six-Speed Transaxle This range is for moving the vehicle backward. Shift into This range should be used for most city and highway REVERSE only after the vehicle has come to a complete driving. It provides the smoothest upshifts, downshifts, stop.
Page 330 STARTING AND OPERATING 329 heavy loading conditions, (i.e., in hilly terrain, traveling the transaxle into third gear, the transaxle will never shift into strong head winds or while towing heavy trailers). above third gear, but can shift down into second or first Under these conditions, using the “3”...
Page 331 330 STARTING AND OPERATING second gear (third gear for six-speed) despite the forward Odometer gear selected. PARK, REVERSE, and NEUTRAL will Screen Display continue to operate. This Reset feature allows the vehicle Actual Gear(s) 1-2 1-3 1-4 to be driven to an authorized dealer for service without Allowed (Six- damaging the transaxle.
Page 332: Driving On Slippery Surfaces
STARTING AND OPERATING 331 If the transaxle cannot be reset, authorized dealer service Traction is required. When driving on wet or slushy roads, it is possible for a layer of water to build up between the tire and road DRIVING ON SLIPPERY SURFACES surface.
Page 333: Driving Through Water
332 STARTING AND OPERATING DRIVING THROUGH WATER Shallow Standing Water Driving through water more than a few inches/ Although your vehicle is capable of driving through centimeters deep will require extra caution to ensure shallow standing water, consider the following Caution safety and prevent damage to your vehicle.
Page 334 STARTING AND OPERATING 333 CAUTION! (Continued) WARNING! • Driving through standing water may cause dam- • Driving through standing water limits your vehi- age to your vehicle’s drivetrain components. Al- cle’s traction capabilities. Do not exceed 5 mph ways inspect your vehicle’s fluids (i.e., engine oil, (8 km/h) when driving through standing water.
Page 335: Power Steering
334 STARTING AND OPERATING POWER STEERING system. This noise should be considered normal, and it The standard power steering system will give you good does not in any way damage the steering system. vehicle response and increased ease of maneuverability WARNING! in tight spaces.
Page 336: Power Steering Fluid Check
STARTING AND OPERATING 335 Power Steering Fluid Check WARNING! Checking the power steering fluid level at a defined service interval is not required. The fluid should only be Fluid level should be checked on a level surface and checked if a leak is suspected, abnormal noises are with the engine off to prevent injury from moving apparent, and/or the system is not functioning as antici- parts and to ensure accurate fluid level reading.
Page 337 336 STARTING AND OPERATING The foot operated parking brake is positioned below the When the parking brake is applied with the ignition lower left corner of the instrument panel. To apply the switch in the ON position, the “Brake Warning Light” in park brake, firmly push the park brake pedal fully.
Page 338 STARTING AND OPERATING 337 to move the shift lever out of PARK. The parking brake WARNING! (Continued) should always be applied whenever the driver is not in • Always fully apply the parking brake when leav- the vehicle. ing your vehicle, or it may roll and cause damage or injury.
Page 339: Anti-Lock Brake System (Abs)
338 STARTING AND OPERATING • A slight drop or fall away of the brake pedal at the end ANTI-LOCK BRAKE SYSTEM (ABS) The Anti-Lock Brake System (ABS) provides increased of the stop vehicle stability and brake performance under most WARNING! braking conditions.
Page 340: Anti-Lock Brake Warning Light
STARTING AND OPERATING 339 Anti-Lock Brake Warning Light WARNING! (Continued) The “Anti-Lock Brake Warning Light” moni- • The Anti-Lock Brake System cannot prevent acci- tors the anti-lock brake system. The light will dents, including those resulting from excessive come on when the ignition switch is turned to speed in turns, following another vehicle too the ON position and may stay on for as long as closely, or hydroplaning.
Page 341: Electronic Brake Control System
340 STARTING AND OPERATING If both the “Brake Warning Light” and the “Anti-Lock wheel(s) and engine power is reduced, to provide en- Brake Warning Light” remain on, the ABS and Electronic hanced acceleration and stability. A feature of the TCS Brake Force Distribution (EBD) systems are not function- functions similarly to a limited-slip differential, and ing.
Page 342: Brake Assist System (Bas)
STARTING AND OPERATING 341 application, and then applies optimum pressure to the WARNING! brakes. This can help reduce braking distances. The BAS • The TCS cannot prevent the natural laws of phys- complements the ABS. Applying the brakes very quickly results in the best BAS assistance.
Page 343: Electronic Stability Program (Esp)
342 STARTING AND OPERATING ESP uses sensors in the vehicle to determine the vehicle WARNING! (Continued) path intended by the driver and compares it to the actual • The BAS cannot prevent accidents, including path of the vehicle. When the actual path does not match those resulting from excessive speed in turns, the intended path, ESP applies the brake of the appropri- driving on very slippery surfaces, or hydroplan-...
Page 344: Esp/Bas Warning Light
STARTING AND OPERATING 343 NOTE: To improve the vehicle’s traction when driving ESP Partial Off This mode is entered by momentarily pressing the “ESP with snow chains, or starting off in deep snow, sand or OFF” switch (located in the center switch bank, next to gravel, it may be desirable to switch to the “Partial Off”...
Page 345: Tire Safety Information
344 STARTING AND OPERATING kilometers at speeds greater than 30 mph (48 km/h), see TIRE SAFETY INFORMATION your authorized dealer as soon as possible to have the Tire Markings problem diagnosed and corrected. NOTE: • The “ESP/TCS Indicator Light” and the “ESP/BAS Warning Light”...
Page 346 STARTING AND OPERATING 345 NOTE: tires is the same as for P-Metric tires except for the letters “LT” that are molded into the sidewall preced- • P (Passenger) - Metric tire sizing is based on U.S. ing the size designation. Example: LT235/85R16. design standards.
Page 347 346 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ..blank..= Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm)
Page 348 STARTING AND OPERATING 347 EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
Page 349: Tire Identification Number (Tin)
348 STARTING AND OPERATING Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side.
Page 350: Tire Terminology And Definitions
STARTING AND OPERATING 349 Tire Terminology and Definitions Term Definition The vehicle B-Pillar is a structural member of the body located B-Pillar between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold Tire Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
Page 351: Tire Loading And Tire Pressure
350 STARTING AND OPERATING Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle Tire Placard Location...
Page 352 STARTING AND OPERATING 351 occupants and cargo should never exceed XXX lbs or 3) tire size designed for your vehicle XXX kg” on the Tire and Loading Information placard. 4) cold tire inflation pressures for the front, rear, and The combined weight of occupants, cargo/luggage and spare tires.
Page 353 352 STARTING AND OPERATING available cargo and luggage load capacity is 650 lbs NOTE: • The following table shows examples on how to calcu- (295 kg) (since 5 x 150 = 750, and 1400 – 750 = 650 lbs [295 kg]). late total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations 5.
Page 354 STARTING AND OPERATING 353...
Page 355: Tires - General Information
354 STARTING AND OPERATING Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause accidents. recommended load capacity for your vehicle.
Page 356: Tire Inflation Pressures
STARTING AND OPERATING 355 Tire Inflation Pressures WARNING! (Continued) The proper cold tire inflation pressure is listed on the • Unequal tire pressures from one side of the ve- driver’s side “B” Pillar. hicle to the other can cause the vehicle to drift to The tire pressure should be checked and adjusted, and the right or left.
Page 357: Tire Pressures For High-Speed Operation
356 STARTING AND OPERATING Inflation pressures specified on the placard are always inflation pressure should be increased by 3 psi (21 kPa), “cold tire inflation pressure.” Cold tire inflation pressure which equals 1 psi (7 kPa) for every 12°F (7°C) for this is defined as the tire pressure after the vehicle has not outside temperature condition.
Page 358: Radial-Ply Tires
STARTING AND OPERATING 357 Cuts and punctures in radial tires are repairable only in WARNING! the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs. High-speed driving, with your vehicle at or above maximum load, is dangerous. The added strain on Compact Spare Tire your tires could cause them to fail.
Page 359: Tire Spinning
358 STARTING AND OPERATING WARNING! (Continued) CAUTION! • Temporary-use spare tires have limited tread life. Because of the reduced ground clearance, do not take When the tread is worn to the tread wear indica- your vehicle through an automatic car wash with the tors, the temporary use spare tire needs to be compact spare installed.
Page 360: Tread Wear Indicators
STARTING AND OPERATING 359 WARNING! • Fast spinning tires can be dangerous. Forces gen- erated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. • Do not spin your vehicle’s wheels faster than 30 mph (48 km/h), or for more than 30 seconds continuously, when you are stuck;...
Page 361: Life Of Tire
360 STARTING AND OPERATING Life of Tire Replacement Tires The service life of a tire is dependent upon varying The tires on your new vehicle provide a balance of many factors, including, but not limited to: characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
Page 362: Tire Chains
STARTING AND OPERATING 361 WARNING! WARNING! (Continued) • Failure to equip your vehicle with tires having • Do not use a tire, wheel size or rating other than adequate speed capability can result in sudden tire that specified for your vehicle. Some combinations failure and loss of vehicle control.
Page 363 362 STARTING AND OPERATING CAUTION! CAUTION! (Continued) • Install chains on the front wheels as tightly as To avoid damage to your vehicle or tires, observe the possible and then retighten after driving about following precautions: 0.5 mile (0.8 km). •...
Page 364: Snow Tires
STARTING AND OPERATING 363 SNOW TIRES TIRE ROTATION RECOMMENDATIONS Some areas of the country require the use of snow tires Tires on the front and rear axles of vehicles operate at during Winter. Standard tires are of the all-season type different loads and perform different steering, driving, and satisfy this requirement as indicated by the M+S and braking functions.
Page 365: Tire Pressure Monitor System (Tpms)
364 STARTING AND OPERATING The suggested rotation method is shown in the following TIRE PRESSURE MONITOR SYSTEM (TPMS) diagram. The TPMS will warn the driver of a low tire pressure based on the cold inflation tire pressure requirements found on the tire placard located on the driver’s-side B-pillar.
Page 366 STARTING AND OPERATING 365 The TPMS will warn the driver of a low tire pressure if For example, your vehicle may have a recommended the tire pressure falls below the low pressure warning cold (parked for more than three hours) tire pressure of threshold for any reason, including low temperature 35 psi (241 kPa).
Page 367 366 STARTING AND OPERATING NOTE: CAUTION! • The TPMS is not intended to replace normal tire care • The TPMS has been optimized for the original and maintenance, or to provide warning of a tire failure or condition. equipment tires and wheels. TPMS pressures have been established for the tire size equipped on your •...
Page 368: Base System
STARTING AND OPERATING 367 • Seasonal temperature changes will affect tire pressure, Tire Pressure Monitoring Low Tire Pressure and the TPMS will monitor the actual tire pressure in Warnings the tire. The “TPMS Telltale Warning Light” will illu- minate in the instrument cluster, and an au- Base System dible chime will be activated when one or more The TPMS uses wireless technology with wheel rim...
Page 369 368 STARTING AND OPERATING detected. The system fault will also sound a chime. If the Vehicles with Compact Spare ignition switch is cycled, this sequence will repeat, pro- 1. The compact spare tire (if equipped) does not have a viding the system fault still exists. The “TPMS Warning TPMS sensor.
Page 370: Premium System - If Equipped
STARTING AND OPERATING 369 5. Once you repair or replace the original road tire and The Premium TPMS consists of the following compo- reinstall it on the vehicle in place of the compact spare nents: tire, the TPMS will automatically update, and the “TPMS •...
Page 371 370 STARTING AND OPERATING TPMS Low Pressure Warnings The “TPMS Telltale Warning Light” will illuminate in the instrument cluster, and an audible chime will be acti- vated when one or more of the four active road tire pressures are low. In addition, the EVIC will display a Low Pressure message for three seconds and a graphic display of the pressure value(s) with the low tire(s) flashing.
Page 372 STARTING AND OPERATING 371 the “TPMS Telltale Warning Light” will extinguish once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) to receive this information. Check TPMS Message The “TPMS Telltale Warning Light”...
Page 373 372 STARTING AND OPERATING will not be present, and a pressure value will be dis- 2. If you install the compact spare tire in place of a road played instead of dashes. A system fault can occur by any tire that has a pressure below the low-pressure warning of the following scenarios: limit, upon the next ignition switch cycle, the “TPMS Telltale Warning Light”...
Page 374: Fuel Requirements
STARTING AND OPERATING 373 • This device must accept any interference received, 5. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the compact spare, including interference that may cause undesired the TPMS will update automatically.
Page 375: 4.0L Engine
374 STARTING AND OPERATING 4.0L Engine Over 40 automobile manufacturers around the world The 4.0L engine is designed to meet all have issued and endorsed consistent gasoline specifica- emissions regulations and provide satisfac- tions (the World Wide Fuel Charter, WWFC) to define tory fuel economy and performance when fuel properties necessary to deliver enhanced emissions, using high-quality unleaded gasoline hav-...
Page 376: Gasoline/Oxygenate Blends
STARTING AND OPERATING 375 Gasoline/Oxygenate Blends E85 Usage In Non-Flex Fuel Vehicles Some fuel suppliers blend unleaded gasoline with oxy- Non-FFV vehicles are compatible with gasoline contain- genates such as 10% ethanol, MTBE, and ETBE. Oxygen- ing 10% ethanol (E10). Gasoline with higher ethanol ates are required in some areas of the country during the content may void the vehicle’s warranty.
Page 377: Mmt In Gasoline
376 STARTING AND OPERATING • disconnect and reconnect the battery to reset the It is even more important to look for gasoline without engine controller memory MMT in Canada, because MMT can be used at levels higher than those allowed in the United States. More extensive repairs will be required for prolonged exposure to E85 fuel.
Page 378: Fuel System Cautions
STARTING AND OPERATING 377 Fuel System Cautions CAUTION! (Continued) • The use of fuel additives which are now being CAUTION! sold as octane enhancers is not recommended. Follow these guidelines to maintain your vehicle’s Most of these products contain high concentra- performance: tions of methanol.
Page 379: Carbon Monoxide Warnings
378 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! (Continued) • Guard against carbon monoxide with proper WARNING! maintenance. Have the exhaust system inspected Carbon monoxide (CO) in exhaust gases is deadly. every time the vehicle is raised. Have any abnor- •...
Page 380 STARTING AND OPERATING 379 the other sections of this manual for information on CAUTION! features that are common between Flexible Fuel and gasoline only powered vehicles. Only vehicles with the E85 fuel filler door label can operate on E85. E85 Fuel Cap E85 Badge...
Page 381: Ethanol Fuel (E85)
380 STARTING AND OPERATING Ethanol Fuel (E85) For best results, a refueling pattern that avoids alternat- E85 is a mixture of approximately 85% fuel ethanol and ing between E85 and unleaded gasoline is recom- 15% unleaded gasoline. mended. When you do switch fuel types, it is recommended that: WARNING! •...
Page 382: Selection Of Engine Oil For Flexible Fuel Vehicles E85 And Gasoline Vehicles
32°F (0°C). in MOPAR engine oils, and in equivalent oils meeting Cruising Range Chrysler Specification MS-6395. The manufacturer only Because E85 fuel contains less energy per gallon/liter recommends engine oils that are API Certified and meet than gasoline, you will experience an increase in fuel the requirements of Material Standard MS-6395.
Page 383: Starting And Operating ▫ Replacement Parts
382 STARTING AND OPERATING Replacement Parts CAUTION! Many components in your Flexible Fuel Vehicle (FFV) are designed to be compatible with ethanol. Always be sure Do not use ethanol mixture greater than 85% in your that your vehicle is serviced with correct ethanol com- vehicle.
Page 384 STARTING AND OPERATING 383 CAUTION! WARNING! (Continued) • Never add fuel when the engine is running. This is • Damage to the fuel system or emissions control in violation of most state and federal fire regula- system could result from using an improper fuel tions and will cause the MIL to turn on.
Page 385: Loose Fuel Filler Cap Message
384 STARTING AND OPERATING Loose Fuel Filler Cap Message VEHICLE LOADING If the vehicle diagnostic system determines that the fuel As required by National Highway Traffic Safety Admin- filler cap is loose, improperly installed, or damaged, a istration regulations, your vehicle has a certification label “gASCAP”...
Page 386 STARTING AND OPERATING 385 • Vehicle Identification Number (VIN) WARNING! • Type of Vehicle Because the front wheels drive and steer the vehicle, • Month, Day and Hour of Manufacture (MDH) it is important that you do not exceed the maximum front or rear GAWR.
Page 387 386 STARTING AND OPERATING Curb Weight The best way to figure out the total weight of your The curb weight of a vehicle is defined as the total weight vehicle is to weigh it when it is fully loaded and ready for of the vehicle with all fluids, including vehicle fuel, at full operation.
Page 388 STARTING AND OPERATING 387 Loading CAUTION! To load your vehicle properly, first figure out its empty weight, axle-by-axle and side-by-side. Store heavier items Do not load your vehicle any heavier than the GVWR down low and be sure you distribute their weight as or the maximum front and rear GAWR.
Page 389 388 STARTING AND OPERATING A loaded vehicle is shown in the illustration. Note that LOADING TABLE — EXAMPLE ONLY neither the GVWR or the GAWR capacities have been Front Axle Rear Axle exceeded. Empty Weight 2,140 lbs 1,470 lbs (971 kg) (667 kg) Load (Driver, 360 lbs (163 kg)
Page 390: Trailer Towing
STARTING AND OPERATING 389 TRAILER TOWING Gross Trailer Weight (GTW) In this section you will find safety tips and information The GTW is the weight of the trailer plus the weight of all on limits to the type of towing you can reasonably do cargo, consumables and equipment (permanent or tem- with your vehicle.
Page 391 390 STARTING AND OPERATING that typically provides adjustable friction associated with WARNING! the telescoping motion to dampen any unwanted trailer swaying motions while traveling. It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition Weight-Carrying Hitch can result if either rating is exceeded.
Page 392 STARTING AND OPERATING 391 safety. The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability. Trailer sway control and a weight distributing (load equalizing) hitch are recommended for heavier tongue weights (TW), and may be required depending on vehicle and trailer configuration/loading to comply with gross axle weight rating (GAWR) requirements.
Page 393 392 STARTING AND OPERATING With Weight-Distributing Hitch (Correct) Improper Adjustment of Weight-Distributing Hitch (Incorrect)
Page 394 STARTING AND OPERATING 393 Trailer Hitch Classification TRAILER HITCH CLASSIFICATIONS Your vehicle may be factory-equipped for safe towing of Max. GTW (Gross Trailer Class trailers weighing over 2,000 lbs (907 kg) with the optional Wt.) Trailer Tow Prep Package. See an authorized dealer for Class I - Light Duty 2,000 lbs (907 kg) package content.
Page 395 394 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. 2Engine/ GCWR (Gross Com- Max. GTW Max. Tongue Frontal Area Transaxle bined Wt. Rating) (Gross Trailer Wt.) Up to 2 persons &...
Page 396 STARTING AND OPERATING 395 Trailer and Trailer Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
Page 397 396 STARTING AND OPERATING NOTE: Remember that everything put into or on the CAUTION! trailer adds to the load on your vehicle. Also, additional • Do not tow a trailer at all during the first 500 miles factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on (805 km) the new vehicle is driven.
Page 398 STARTING AND OPERATING 397 WARNING! WARNING! (Continued) • Safety chains must always be used between your Improper towing can lead to an injury accident. vehicle and trailer. Always connect the chains to Follow these guidelines to make your trailer towing the frame or hook retainers of the vehicle hitch.
Page 399 398 STARTING AND OPERATING • Check for signs of tire wear or visible tire damage WARNING! (Continued) before towing a trailer. Refer to “Tires – General 3. GAWR Information” in “Starting and Operating” for the 4. Trailer tongue weight rating for that trailer hitch. proper inspection procedure.
Page 400 STARTING AND OPERATING 399 • An electronically actuated trailer brake controller is WARNING! required when towing a trailer with electronically • Do not connect trailer brakes to your vehicle’s actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic hydraulic brake lines.
Page 401 400 STARTING AND OPERATING Towing Requirements – Trailer Lights and Wiring Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are required for motoring safety. The Trailer Tow Package may include a four-pin or a seven-pin wiring harness.
Page 402: Towing Tips
STARTING AND OPERATING 401 Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. Automatic Transaxle The DRIVE gear can be selected when towing. However, if frequent shifting occurs while in DRIVE, move the shift lever into third gear (with four-speed transaxle) or fifth gear (with six-speed transaxle).
Page 403 402 STARTING AND OPERATING • Use speed control in flat terrain and with light loads to The automatic transaxle fluid and filter should be changed if you REGULARLY tow a trailer for more than maximize fuel efficiency. 45 minutes of continuous operation. Refer to “Mainte- Cooling System nance Schedule”...
Page 404: Recreational Towing (Behind Motorhome, Etc.)
STARTING AND OPERATING 403 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) CAUTION! Towing this vehicle behind another vehicle (flat- towing with all four wheels on the ground) is not recommended. NOTE: If the vehicle requires towing, make sure all four wheels are off the ground.
Page 406: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS ▫ Secure The Spare Tire ....419 Hazard Warning Flasher ....406 If Your Engine Overheats .
Page 407: Hazard Warning Flasher
406 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located in the In any of the following situations, you can reduce the center of the instrument panel above the radio. potential for overheating by taking the appropriate ac- tion.
Page 408 WHAT TO DO IN EMERGENCIES 407 to high. This allows the heater core to act as a WARNING! supplement to the radiator and aids in removing heat from the engine cooling system. You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.
Page 409: Jacking And Tire Changing
408 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING Jack Location The jack, jack handle and winch handle tools are stowed WARNING! behind the rear left side trim panel in the rear cargo area. Turn the two cover latches to release the cover. •...
Page 410: Spare Tire Removal
WHAT TO DO IN EMERGENCIES 409 NOTE: The base console, if equipped, must be removed Spare Tire Removal The spare tire is stowed inside a protective cover located to raise and lower the spare tire. Refer to “Console under the center of the vehicle between the front doors by Features”...
Page 411: Jacking Instructions
410 WHAT TO DO IN EMERGENCIES NOTE: Passengers should not remain in the vehicle WARNING! when the vehicle is being jacked. Do not attempt to change a tire on the side of the Jacking Instructions vehicle close to moving traffic. Pull far enough off the road to avoid being hit when operating the jack WARNING! or changing the wheel.
Page 412 WHAT TO DO IN EMERGENCIES 411 WARNING! (Continued) • Never start or run the engine with the vehicle on a jack. • Do not let anyone sit in the vehicle when it is on a jack. Jack Warning Label • Do not get under the vehicle when it is on a jack. 1.
Page 413 412 WHAT TO DO IN EMERGENCIES 2. To remove the compact spare tire/cover assembly, assemble the winch handle extensions to form a “T” and fit the winch “T” handle over the drive nut, refer to “2” configuration in tool graphics. Rotate the nut to the left until the winch mechanism stops turning freely.
Page 414 WHAT TO DO IN EMERGENCIES 413 CAUTION! The winch mechanism is designed for use with the winch “T” handle only. Use of an air wrench or other power tools is not recommended and can damage the winch. 3. Assemble the winch handle extensions to form the Spare Tire Hook and pull the compact spare tire/cover assembly from under the vehicle, refer to “1”...
Page 415 414 WHAT TO DO IN EMERGENCIES WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.
Page 416 WHAT TO DO IN EMERGENCIES 415 NOTE: • Rear jack locations are between a pair of down-facing tabs on the sill flange of the vehicle side body. • Front jack locations are on the sill flange of the vehicle side body, and align with front door edges. Squeezing Winch Retainer Tabs 5.
Page 417 416 WHAT TO DO IN EMERGENCIES Jack Location...
Page 418 WHAT TO DO IN EMERGENCIES 417 CAUTION! WARNING! Do not attempt to raise the vehicle by jacking on Raising the vehicle higher than necessary can make locations other than those indicated in Step 5. the vehicle less stable. It could slip off the jack and hurt someone near it.
Page 419: Wheel Nuts
418 WHAT TO DO IN EMERGENCIES 10. Lower the vehicle by turning the jack screw to the 13. Place the deflated (flat) tire and compact spare tire left. cover assembly. in the rear cargo area. Do not stow the deflated tire in the spare tire location. Have the full- 11.
Page 420: Secure The Spare Tire
WHAT TO DO IN EMERGENCIES 419 of operation, and after each time a tire is changed, to WARNING! allow the wheel nuts to become properly set. All nuts should first be firmly seated against the wheel. The nuts A loose compact spare tire/cover assembly, thrown should then be tightened to recommended torque.
Page 421 420 WHAT TO DO IN EMERGENCIES 2. Assemble the winch handle extensions to form the WARNING! spare tire hook, and pull the wheel spacer from under the vehicle. Verify that both retainer tabs of the wheel spacer have been properly extended through the center of 3.
Page 422: Jump-Starting Procedure
WHAT TO DO IN EMERGENCIES 421 CAUTION! CAUTION! The winch mechanism is designed specifically to Do not use a portable battery booster pack or any stow a compact spare tire only. Do not attempt to use other booster source with a system voltage greater the winch to stow the full size flat tire, or any other than 12 Volts or damage to the battery, starter motor, full-size tire.
Page 423: Preparations For Jump-Start
422 WHAT TO DO IN EMERGENCIES Preparations for Jump-Start WARNING! The battery in your vehicle is located on the left side of • Take care to avoid the radiator cooling fan when- the engine compartment. ever the hood is raised. It can start anytime the ignition switch is on.
Page 424: Jump-Starting Procedure
WHAT TO DO IN EMERGENCIES 423 3. If using a another vehicle to jump-start the battery, CAUTION! park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. Failure to follow these procedures could result in damage to the charging system of the booster vehicle WARNING! or the discharged vehicle.
Page 425 424 WHAT TO DO IN EMERGENCIES 8. Disconnect the opposite end of the positive (+) jumper WARNING! cable from the positive (+) post of the booster battery. Do not connect the cable to the negative post (-) of the 9. Disconnect the positive (+) end of the jumper cable discharged battery.
Page 426: Freeing A Stuck Vehicle
WHAT TO DO IN EMERGENCIES 425 FREEING A STUCK VEHICLE CAUTION! (Continued) If your vehicle becomes stuck in mud, sand or snow, it • Revving the engine or spinning the wheels too fast can often be moved by a rocking motion. Turn your may lead to transmission overheating and failure.
Page 427: Towing A Disabled Vehicle
426 WHAT TO DO IN EMERGENCIES • The towing speed must not exceed 30 mph (50 km/h). WARNING! CAUTION! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or Exceeding these towing limits may cause severe even failure, of the axle and tires.
Page 428 WHAT TO DO IN EMERGENCIES 427 Towing Without The Ignition Key CAUTION! (Continued) Special care must be taken when the vehicle is towed • Always use wheel lift equipment when towing with the ignition in the OFF position. The only approved from the front.
Page 430 MAINTAINING YOUR VEHICLE CONTENTS ▫ Engine Oil ......437 Engine Compartment — 3.3/3.8L ..431 ▫...
Page 431 430 MAINTAINING YOUR VEHICLE ▫ Brakes ......454 ▫ Front Park/Turn Signal Lamp ... 477 ▫...
Page 432: Engine Compartment - 3.3/3.8L
MAINTAINING YOUR VEHICLE 431 ENGINE COMPARTMENT — 3.3/3.8L 1 — Air Cleaner Filter 7 — Engine Oil Fill 2 — Automatic Transmission Dipstick (3.3L Only) 8 — Engine Oil Dipstick 3 — Brake Fluid Reservoir 9 — Coolant Pressure Cap 4 —...
Page 433: Engine Compartment - 4.0L
432 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 4.0L 1 — Power Steering Fluid Reservoir 7 — Engine Oil Dipstick 2 — Air Cleaner Filter 8 — Engine Oil Fill 3 — Brake Fluid Reservoir 9 — Coolant Pressure Cap 4 — Battery 10 —...
Page 434: Onboard Diagnostic System - Obd Ii
MAINTAINING YOUR VEHICLE 433 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic further damage to the emission control system.
Page 435: Emissions Inspection And Maintenance Programs
434 MAINTAINING YOUR VEHICLE “Electronic Vehicle Information Center (EVIC)” in ”Un- For states that require an Inspection and Mainte- derstanding Your Instrument Panel” for further informa- nance (I/M), this check verifies the “Malfunction tion. Tighten the gas cap until a clicking sound is heard. Indicator Light (MIL)”...
Page 436 MAINTAINING YOUR VEHICLE 435 2. If you crank or start the engine, you will have to start If your OBD II system is not ready, you should see your this test over. authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, 3.
Page 437: Replacement Parts
436 MAINTAINING YOUR VEHICLE REPLACEMENT PARTS WARNING! Use of genuine MOPAR parts for normal/scheduled maintenance and repairs is highly recommended to en- You can be badly injured working on or around a sure the designed performance. Damage or failures motor vehicle. Only do service work for which you caused by the use of non-MOPAR parts for maintenance have the knowledge and the proper equipment.
Page 438: Engine Oil
Immediately have potential malfunctions fully warmed engine is shut OFF or before starting the examined by an authorized Chrysler Group LLC engine after it has sat overnight. dealership or qualified repair center.
Page 439 Such damage is For best performance and maximum protection under all not covered by the New Vehicle Limited Warranty. types of operating conditions, the manufacturer only recommends engine oils that are API certified and meet the requirements of Chrysler Material Standard MS-6395.
Page 440 MAINTAINING YOUR VEHICLE 439 For information on engine oil filler cap location, refer to Engine Oil Viscosity (SAE Grade) – 3.3L & 3.8L Gasoline Engines “Engine Compartment” in “Maintaining Your Vehicle” SAE 5W-20 engine oil is recommended for all operating for further information.
Page 441: Engine Oil Filter
440 MAINTAINING YOUR VEHICLE Disposing of Used Engine Oil and Oil Filters Engine Air Cleaner Filter Care should be taken in disposing of used engine oil and Refer to “Maintenance Schedule” for further information. oil filters from your vehicle. Used oil and oil filters, WARNING! indiscriminately discarded, can present a problem to the environment.
Page 442: Exhaust System
MAINTAINING YOUR VEHICLE 441 used to assure most efficient service. MOPAR engine air WARNING! cleaner filters are a high quality filter and are recommended. Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Exhaust System Breathing it can make you unconscious and can The best protection against carbon monoxide entry into...
Page 443 442 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- NOTE: Intentional tampering with emissions control verter will not require maintenance. However, it is im- systems can result in civil penalties being assessed portant to keep the engine properly tuned to assure against you.
Page 444: Maintenance-Free Battery
MAINTAINING YOUR VEHICLE 443 To minimize the possibility of catalyst damage: WARNING! • Do not shut OFF the engine or interrupt the ignition • Battery fluid is a corrosive acid solution and can when the transaxle is in gear and the vehicle is in burn or even blind you.
Page 445: Air Conditioner Maintenance
444 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance CAUTION! For best possible performance, your air conditioner • It is essential when replacing the cables on the should be checked and serviced by an authorized dealer at the start of each warm season. This service should battery that the positive cable is attached to the include cleaning of the condenser fins and a system positive post and the negative cable is attached to...
Page 446 MAINTAINING YOUR VEHICLE 445 Refrigerant Recovery and Recycling WARNING! R-134a air conditioning refrigerant is a hydrofluoro- • Use only refrigerants and compressor lubricants carbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. How- approved by the manufacturer for your air condi- ever, the manufacturer recommends that air conditioning tioning system.
Page 447 446 MAINTAINING YOUR VEHICLE A/C Air Filter – If Equipped Refer to “Maintenance Schedule” for further information. WARNING! Do not remove the A/C air filter while the blower is operating or personal injury may result. The A/C air filter is located in the fresh air inlet behind the glove box.
Page 448: Body Lubrication
MAINTAINING YOUR VEHICLE 447 hood latching components to ensure proper function. CAUTION! When performing other underhood services, the hood latch, release mechanism and safety catch should be The A/C air filter is labeled with an arrow to indicate cleaned and lubricated. airflow direction through the filter.
Page 449 448 MAINTAINING YOUR VEHICLE Avoid using the wiper blades to remove frost or ice from The washer fluid reservoir will hold a full gallon of fluid the windshield. Keep the blade rubber out of contact with when the Low Washer Fluid Light illuminates. petroleum products such as engine oil, gasoline, etc.
Page 450: Cooling System
MAINTAINING YOUR VEHICLE 449 rusty in appearance, the system should be drained, Cooling System flushed and refilled with fresh coolant. Check the front of WARNING! the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden •...
Page 451 450 MAINTAINING YOUR VEHICLE Cooling System – Drain, Flush and Refill CAUTION! If the engine coolant (antifreeze) is dirty or contains a • Mixing of engine coolant (antifreeze) other than considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough specified Hybrid Organic Additive Technology rinsing to remove all deposits and chemicals.
Page 452 MAINTAINING YOUR VEHICLE 451 When adding engine coolant (antifreeze), a minimum CAUTION! (Continued) solution of 50% recommended MOPAR Antifreeze/ • This vehicle has not been designed for use with Coolant Five Year/100,000 Mile Formula HOAT (Hybrid Propylene Glycol-based engine coolant (anti- Organic Additive Technology), or equivalent, in water freeze).
Page 453 452 MAINTAINING YOUR VEHICLE NOTE: Mixing engine coolant (antifreeze) types will WARNING! decrease the life of the engine coolant (antifreeze) and • The warning words “DO NOT OPEN HOT” on will require more frequent coolant changes. the cooling system pressure cap are a safety pre- Cooling System Pressure Cap caution.
Page 454 MAINTAINING YOUR VEHICLE 453 engine coolant (antifreeze) freeze point or replacing the Disposal of Used Coolant Used ethylene glycol-based engine coolant (antifreeze) is engine coolant (antifreeze). Advise your service atten- a regulated substance requiring proper disposal. Check dant of this. As long as the engine operating temperature with your local authorities to determine the disposal is satisfactory, the coolant bottle only needs to be checked rules for your community.
Page 455: Brakes
454 MAINTAINING YOUR VEHICLE • Make sure that the radiator and coolant recovery If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be bottle overflow hoses are not kinked or obstructed. safely driven.
Page 456 MAINTAINING YOUR VEHICLE 455 Overfilling of fluid is not recommended because it may WARNING! cause leaking in the system. Riding the brakes can lead to brake failure and Add enough fluid to bring the level up to the require- possibly an accident. Driving with your foot resting ments described on the brake fluid reservoir.
Page 457 456 MAINTAINING YOUR VEHICLE WARNING! WARNING! (Continued) • To avoid contamination from foreign matter or • Use only manufacturer’s recommended brake moisture, use only new brake fluid or fluid that fluid. Refer to “Fluids, Lubricants, and Genuine has been in a tightly closed container. Keep the Parts”...
Page 458: Automatic Transaxle
MAINTAINING YOUR VEHICLE 457 All six–speed transaxles are equipped with a capped WARNING! (Continued) dipstick tube. It is sealed and should not be tampered • Do not allow petroleum based fluid to contami- with. Your authorized dealer has the necessary tools to nate the brake fluid.
Page 459 458 MAINTAINING YOUR VEHICLE 2. The engine should be running at curb idle speed for a CAUTION! minimum of 60 seconds. Using a transmission fluid other than the manufac- 3. Fully apply the parking brake. turer’s recommended fluid may cause deterioration 4.
Page 460 MAINTAINING YOUR VEHICLE 459 a. If the fluid is hot, the reading should be in the Fluid Level Check (3.8L and 4.0L Engines with crosshatched area marked “HOT” (between the upper Six-Speed Automatic Transaxle) – If Equipped two holes in the dipstick). The six-speed automatic transaxle is a sealed unit and has no dipstick.
Page 461: Appearance Care And Protection From Corrosion
460 MAINTAINING YOUR VEHICLE The following maintenance recommendations will enable CAUTION! you to obtain maximum benefit from the corrosion resistance built into your vehicle. Do not use chemical flushes in your transaxle as the chemicals can damage your transaxle components. What Causes Corrosion? Such damage is not covered by the New Vehicle Corrosion is the result of deterioration or removal of...
Page 462 MAINTAINING YOUR VEHICLE 461 Washing CAUTION! • Wash your vehicle regularly. Always wash your ve- Do not use abrasive or strong cleaning materials such hicle in the shade using MOPAR Car Wash or equiva- as steel wool or scouring powder, which will scratch lent, or a mild car wash soap, and rinse the panels metal and painted surfaces.
Page 463 462 MAINTAINING YOUR VEHICLE coating, have your vehicle repaired as soon as pos- non-acidic cleaner. Do not use scouring pads, steel wool, sible. The cost of such repairs is considered the respon- a bristle brush, or metal polishes. Only MOPAR sibility of the owner.
Page 464 MAINTAINING YOUR VEHICLE 463 • For grease stains, apply MOPAR Multi-Purpose if absolutely necessary. Do not use harsh cleaners or Cleaner or a equivalent high quality cleaner to a clean, Armor All . Use MOPAR Total Clean or equivalent to damp cloth and remove the stain.
Page 465 464 MAINTAINING YOUR VEHICLE Glass Surfaces WARNING! All glass surfaces should be cleaned on a regular basis with MOPAR Glass Cleaner or equivalent or any com- Do not use volatile solvents for cleaning purposes. mercial household-type glass cleaner. Never use an abra- Many are potentially flammable, and if used in sive type cleaner.
Page 466: Cleaning The Instrument Panel Cupholders
MAINTAINING YOUR VEHICLE 465 1. Clean with a wet soft rag. A mild soap solution may be Cleaning the Instrument Panel Cupholders used, but do not use high alcohol content or abrasive Removal cleaners. If soap is used, wipe clean with a clean damp Pull the flexible liner from the cupholder drawer starting rag.
Page 467: Fuses
466 MAINTAINING YOUR VEHICLE Installation CAUTION! Place the liner into the cupholder drawer and press the • When installing the Totally Integrated Power liner into place so that the retention tabs seat into the corresponding openings in the drawer. Module cover, it is important to ensure the cover is properly positioned and fully latched.
Page 468 MAINTAINING YOUR VEHICLE 467 The numbers inside the TIPM cover correspond to the FUSES/TIPM following table. Cartridge Mini- Cavity Description FUSES/TIPM Fuse Fuse Cartridge Mini- 30 Amp — Anti-Lock Brake Cavity Description Fuse Fuse Pink System (ABS) Valve/ESP 40 Amp —...
Page 469 468 MAINTAINING YOUR VEHICLE FUSES/TIPM FUSES/TIPM Cartridge Mini- Cartridge Mini- Cavity Description Cavity Description Fuse Fuse Fuse Fuse 40 Amp — Rear Window De- 25 Amp — Sunroof Module Green fogger Natural 30 Amp — Rear Blower — 15 Amp Center High Pink Blue...
Page 470 MAINTAINING YOUR VEHICLE 469 FUSES/TIPM FUSES/TIPM Cartridge Mini- Cartridge Mini- Cavity Description Cavity Description Fuse Fuse Fuse Fuse — 20 Amp Power Outlet #2 — 15 Amp Ignition Off Draw Yellow (BATT/ACC SE- Blue — Vehicle Enter- LECT) tainment System (IOD-VES), Satellite —...
Page 471 470 MAINTAINING YOUR VEHICLE FUSES/TIPM FUSES/TIPM Cartridge Mini- Cartridge Mini- Cavity Description Cavity Description Fuse Fuse Fuse Fuse — 30 Amp Amplifier (AMP)/ — 20 Amp Rear View Mirror Green Radio Yellow (RR VW MIR), Cabin Compart- — 20 Amp Ignition Off ment Node (CCN), Yellow...
Page 472 MAINTAINING YOUR VEHICLE 471 FUSES/TIPM FUSES/TIPM Cartridge Mini- Cartridge Mini- Cavity Description Cavity Description Fuse Fuse Fuse Fuse — 10 Amp Occupant Restraint — 15 Amp Cabin Compart- Controller/ Blue ment Node Interior Occupant Classifi- Light (CCN INT cation Module LIGHT), Switch (ORC/OCM) Bank (SW BANK),...
Page 473 472 MAINTAINING YOUR VEHICLE FUSES/TIPM FUSES/TIPM Cartridge Mini- Cartridge Mini- Cavity Description Cavity Description Fuse Fuse Fuse Fuse — 25 Amp Rear Wiper (REAR — 10 Amp Ignition Switch Natural WIPER) (IGN SW), Wireless Ignition Node — 20 Amp Fuel Pump (FUEL Module (WIN Yellow PUMP), Diesel Lift...
Page 474 MAINTAINING YOUR VEHICLE 473 FUSES/TIPM FUSES/TIPM Cartridge Mini- Cartridge Mini- Cavity Description Cavity Description Fuse Fuse Fuse Fuse — 15 Amp Rear Wiper Module — 10 Amp Park Assist (PRK Blue (RR WIPER MOD), ASST), Heater Ven- Power Folding Mir- tilation, Air Condi- ror (PWR FOLD tioning Module...
Page 475: Vehicle Storage
474 MAINTAINING YOUR VEHICLE The heated mirrors, lower instrument panel power outlet FUSES/TIPM and removable floor console, when in the front position Cartridge Mini- Cavity Description are fused with self-resetting fuses that are only serviceable Fuse Fuse by an authorized dealer. The power seats are fused by a —...
Page 476: Replacement Bulbs
MAINTAINING YOUR VEHICLE 475 • Anytime you store your vehicle, or keep it out of NOTE: For lighted switches, see your authorized dealer service for two weeks or more, run the air conditioning for replacement instructions. system at idle for about five minutes in the fresh air All of the interior bulbs are glass wedge base or glass and high blower setting.
Page 477: Bulb Replacement
476 MAINTAINING YOUR VEHICLE Note 1: The Center High-Mounted Stop Lamp (CHMSL) WARNING! uses LED lamps that are not serviceable separately. The CHMSL must be replaced as an assembly, see your A transient high voltage occurs at the bulb sockets of authorized dealer.
Page 478: Front Park/Turn Signal Lamp
MAINTAINING YOUR VEHICLE 477 3. Twist the headlamp bulb and pull the bulb from the 3. Push the new bulb into the socket and reinstall the headlamp housing. socket by twisting until locked into the headlamp housing. 4. Install the new headlamp bulb and twist until locked into the headlamp housing.
Page 479: Fog Lamp
478 MAINTAINING YOUR VEHICLE Fog Lamp 2. Disconnect wire harness from the bulb. NOTE: Access to the fog lamp bulb is from the rear of 3. Reconnect the wiring harness to the new bulb and the fascia. On the left rear side of the fascia, remove the reinstall the bulb by twisting clockwise.
Page 480 MAINTAINING YOUR VEHICLE 479 Bulb Location Tail Lamp Housing Fastener Removal NOTE: 1 — Stop, Tail, Turn Signal Bulb Combo • If a screwdriver is used, make sure a soft material is 2 — Backup Bulb placed between the vehicle body and tool so not to 3.
Page 481: Center High-Mounted Stop Lamp (Chmsl)
480 MAINTAINING YOUR VEHICLE 5. Replace the bulb, reinstall the socket, and reattach the 1. Using a small screwdriver, press inward the locking lamp assembly. tab on the outboard side of the lamp assembly and pull down on the lamp assembly for removal. Center High-Mounted Stop Lamp (CHMSL) The CHMSL uses LED lamps that are not serviceable 2.
Page 482: Fluid Capacities
MAINTAINING YOUR VEHICLE 481 FLUID CAPACITIES U.S. Metric 20 Gallons 76 Liters Fuel (Approximate) Engine Oil with Filter 3.3L and 3.8L Engine (SAE 5W-20, API Certified) 5 Quarts 4.7 Liters 4.0L Engine (SAE 10W-30, API Certified) 5.5 Quarts 5.2 Liters Cooling System * 3.3L, 3.8L, and 4.0L Engine (MOPAR Engine Coolant/ 13.4 Quarts...
Page 483: Fluids, Lubricants And Genuine Parts
Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Engine Oil – 3.3L and 3.8L Engines Chrysler Material Standard MS-6395. Refer to your oil filler cap for cor- rect SAE grade. Use API Certified SAE 10W-30 Engine Oil, meeting the requirements of Engine Oil –...
Page 484: Chassis
MAINTAINING YOUR VEHICLE 483 Chassis Component Fluid, Lubricant, or Genuine Part MOPAR ATF+4 Automatic Transmission Fluid or equivalent licensed Automatic Transaxle ATF+4 product. MOPAR DOT 3 and SAE J1703 should be used or equivalent. If DOT 3 Brake Master Cylinder brake fluid is not available, then DOT 4 is acceptable.
Page 486 MAINTENANCE SCHEDULES CONTENTS ▫ Required Maintenance Intervals ..488 Emissions Control System Maintenance ..486 Maintenance Schedule ....486...
Page 487 486 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE MAINTENANCE SCHEDULE The Scheduled Maintenance services listed in bold type The oil change indicator system will remind you that it is must be done at the times or mileages specified to ensure time to take your vehicle in for scheduled maintenance. the continued proper functioning of the emissions control On Non-EVIC equipped vehicles, CHAngE OIL will system.
Page 488 MAINTENANCE SCHEDULES 487 “Understanding Your Instrument Panel” or under “In- NOTE: • The oil change indicator message will not monitor the strument Cluster Description/Odometer/Trip Odom- time since the last oil change. Change your vehicle’s eter” in “Understanding Your Instrument Panel” for oil if it has been six months since your last oil change, further information.
Page 489 488 MAINTENANCE SCHEDULES • Inspect the battery and clean and tighten the terminals Required Maintenance Intervals as required. Refer to the Maintenance Schedules on the following pages for the required maintenance intervals. • Check the fluid levels of the coolant reservoir, the brake master cylinder, the power steering and the transaxle and add as needed.
Page 490 ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 491 ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 492 ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 493 ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 494 ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 495 ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 496 ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 497 ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 498 ❏ Replace the timing belt (4.0L engine). ❏ Flush and replace the engine coolant if not done at 60 months. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 499 ❏ Replace accessory drive belt(s). ❏ Change the automatic transaxle fluid & filter. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 500 ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 501 ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play; replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 502 • Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer...
Page 504: If You Need Consumer Assistance
Reporting Safety Defects ....508 ▫ Chrysler Group LLC Customer Center ..506 ▫ In The 50 United States And Washington, D.C.
Page 505 504 IF YOU NEED CONSUMER ASSISTANCE ▫ Traction Grades ..... 511 Publication Order Forms ....509 ▫...
Page 506: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 505 the service advisor and list the items in order of priority. SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the...
Page 507: Chrysler Group Llc Customer Center
• Vehicle delivery date and mileage This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- Chrysler Group LLC Customer Center solved with this process. P.O. Box 21–8004 • If for some reason you are still not satisfied, talk to the Auburn Hills, MI 48321–8004...
Page 508: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
IF YOU NEED CONSUMER ASSISTANCE 507 the manufacturer’s service contracts. If you purchased a Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) manufacturer’s service contract, you will receive Plan To assist customers who have hearing difficulties, the Provisions and an Owner Identification Card in the mail manufacturer has installed special TDD (Telecommuni- within three weeks of the vehicle delivery date.
Page 509: Warranty Information (U.s. Vehicles Only)
See the Warranty Information Booklet, located on the the ownership experience. You’ll be pleased with their DVD, for the terms and provisions of Chrysler Group sincere efforts to resolve any warranty issues or related LLC warranties applicable to this vehicle.
Page 510: In Canada
Customer Service Department imme- need in diagnosing/troubleshooting, problem solving, diately. Canadian customers who wish to report a safety maintaining, servicing, and repairing Chrysler Group defect to the Canadian government should write to: LLC vehicles. A complete working knowledge of the...
Page 511: Department Of Transportation Uniform Tire
510 IF YOU NEED CONSUMER ASSISTANCE vehicle, system, and/or components is written in acquaint you with specific Chrysler Group LLC ve- straightforward language with illustrations, diagrams, hicles. Included are starting, operating, emergency and charts. and maintenance procedures as well as specifications, capabilities and safety tips.
Page 512: Traction Grades
IF YOU NEED CONSUMER ASSISTANCE 511 in each category is shown on the sidewall of the tires on wet pavement, as measured under controlled conditions your vehicle. on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction perfor- All passenger car tires must conform to Federal safety mance.
Page 513 512 IF YOU NEED CONSUMER ASSISTANCE grade C corresponds to a level of performance, which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A repre- sent higher levels of performance on the laboratory test wheel, than the minimum required by law.
Page 514 INDEX...
Page 515 514 INDEX Adding Engine Coolant (Antifreeze) ..451 Airbag Maintenance ..... . . 78 Adding Fuel .
Page 516 INDEX 515 Automatic Transaxle ..... . 324 Belts, Seat ......100 Adding Fluid .
Page 517 516 INDEX Capacities, Fluid ......481 Checking Your Vehicle For Safety ... . . 99 Caps, Filler Checks, Safety .
Page 518 INDEX 517 Computer, Trip/Travel ....249 Radiator Cap ......452 Connector Selection of Coolant (Antifreeze) .
Page 519 518 INDEX Disposal Electronic Speed Control (Cruise Control) ..168 Antifreeze (Engine Coolant) ....453 Electronic Stability Program (ESP) ... . 342 Engine Oil .
Page 520 INDEX 519 Flooded, Starting ..... . 322 Fabric Care ......463 Fuel Requirements .
Page 521 520 INDEX Flooded Engine Starting ....322 Filler Cap (Gas Cap) ....241,382 Floor Console .
Page 522 INDEX 521 Gauges Cleaning ......464 Coolant Temperature ....236 Lights On Reminder .
Page 523 522 INDEX Illuminated Entry ......18 Key, Replacement ......15 Immobilizer (Sentry Key) .
Page 524 INDEX 523 Airbag ..... 67,74,79,100,235 High Beam/Low Beam Select ... . . 161 Alarm .
Page 525 524 INDEX Theft Alarm (Security Alarm) ....233 Maintenance Schedule ....486 Tire Pressure Monitoring (TPMS) .
Page 526 INDEX 525 Mopar Parts ......436,508 Materials Added to ..... 439 Multi-Function Control Lever .
Page 527 526 INDEX Phone, Cellular ......121 Programmable Electronic Features ... . 253 Phone, Hands-Free (Uconnect™) .
Page 528 INDEX 527 Remote Starting System ....27 Safety Tips ......99 Removable Floor Console .
Page 529 528 INDEX Fold in Floor (Stow n Go) ....131 Settings, Personal ......253 Heated .
Page 530 INDEX 529 Starting Procedures ..... . 321 Temperature Control, Automatic (ATC) ..306 Steering Temperature Gauge, Engine Coolant .
Page 531 530 INDEX Life of Tires ......360 Weight ......394 Load Capacity .
Page 532 INDEX 531 Transmitter Battery Service Vanity Mirrors ......112 (Remote Keyless Entry) ....26 Variance, Compass .
Page 533 532 INDEX Water Windows, Express Down ....22 Driving Through ..... . 332 Windshield Defroster .
Page 534 Chrysler Group LLC 10Y531-126-AB Printed in U.S.A. 2nd Edition...

This manual is also suitable for:

2010 town & country

Chrysler Town & Country 2010 Owner's Manual

Town & Country

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

Chapters

Related Manuals for Chrysler Town & Country 2010

Summary of Contents for Chrysler Town & Country 2010