4 INTRODUCTION INTRODUCTION WARNING! This manual has been prepared with the assistance of service and engineering specialists to acquaint you with Engine exhaust, some of its constituents, and certain the operation and maintenance of your new vehicle. It is vehicle components contain or emit chemicals supplemented by a Warranty Information Booklet and known to the State of California to cause cancer and various customer oriented documents.
6 INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures, which could result in an accident or bodily injury. It also contains CAUTIONS against procedures, which could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 9
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Sentry Key — If Equipped ....15 ▫...
Page 10
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Disarm The System ....19 Windows ......31 ▫...
Page 11
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Reinstalling Storage Bin Cover Emergency ▫ DaimlerChrysler Corporation Integrated Child Seat Release ......45 —...
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key Removal The dealer that sold you your new vehicle has the key Automatic Transaxle code numbers for your vehicle locks. These numbers can Place the shift lever in PARK. Turn the ignition switch to be used to order duplicate keys from your dealer.
Page 13
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 WARNING! NEVER leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the keys in the ignition.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key-In-Ignition Reminder If You Wish To Manually Lock The Steering An alarm will sound to remind you if the key is left in the Wheel: ignition and the driver’s door is opened. With the engine running, turn the steering wheel upside down, turn off the engine and remove the key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 NOTE: A key, which has not been programmed, is also Automatic Transaxle Ignition Interlock System This system prevents the key from being removed unless considered an invalid key even if it is cut to fit the the shift lever is in PARK.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Shaft Lock Module (Vehicles Equipped with vehicle. Cell phones, pagers, or other RF electronics will not cause interference with this system. Premium Security System) — If Equipped The shaft lock module is located inside the steering All of the keys provided with your new vehicle have column.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 NOTE: When having the Sentry Key Immobilizer 4. Insert a blank Sentry Key into the ignition switch and System serviced, bring all vehicle keys with you to the turn the ignition switch ON within 60 seconds. After 10 dealer.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information Rearming of the System — If Equipped The Sentry Key system complies with FCC rules part 15 The security system will rearm itself after the 15 addi- and with RSS-210 of Industry Canada. Operation is tional minutes of headlights and security telltale flashing, subject to the following conditions: if the system has not been disabled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: If the SECURITY light stays on continuously The Security Alarm System is designed to protect your during vehicle operation, have the system checked by vehicle; however, you can create conditions where the your dealer.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ILLUMINATED ENTRY SYSTEM — IF EQUIPPED REMOTE KEYLESS ENTRY — IF EQUIPPED The courtesy lights will turn on when you use the keyless This system allows you to lock or unlock the doors and entry transmitter or open the doors.
Page 21
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Three button transmitters will provide basic UNLOCK, options of the system allow you to turn ON/OFF the LOCK and PANIC functions. Sound Horn On Lock, Remote Unlock Driver’s Door 1st, and Flash Lights On Lock/Unlock features. Three Button Transmitter Six Button Transmitter Six button transmitters will provide functions that allow...
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To unlock the doors and liftgate: To lock the doors and liftgate: Press and release the UNLOCK button on the transmitter Press and release the LOCK button on the transmitter to once to unlock the driver’s door side of the vehicle, or lock all doors and liftgate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Using The Panic Alarm: To Program Transmitters: To turn the panic alarm feature ON or OFF, press and Refer to SENTRY KEY “Customer Key Programming.” hold the PANIC button on the transmitter for at least one If you do not have a programmed transmitter, contact second and release.
Page 24
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Open/Close Left Power Sliding Door — If If the vehicle is not equipped with a right power sliding door and the door is closed and locked, pressing the Equipped Press the LEFT button twice within five seconds to button twice will result in the right side doors becoming open/close the left power sliding door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 the procedure in the Electronic Vehicle Information Cen- General Information ter (EVIC), Customer Programmable Features section on This device complies with part 15 of the FCC rules and vehicles so equipped. The table below explains the Lamp RSS 210 of Industry Canada.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transmitter Battery Service The recommended replacement battery is one CR2032 battery. NOTE: Perchlorate Material — special handling may apply. www.dtsc.ca.gov/hazardouswaste/ perchlorate NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To reassemble the transmitter case snap two halves together.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the lock plunger is down when you shut the door, the Power Door Locks — If Equipped door will lock. Therefore, make sure the keys are not A power door lock switch is on each front door trim inside the vehicle before closing the door.
Page 29
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 • On electronic vehicle information center (EVIC) If you press the power door lock switch while the key is in the ignition, and any front door is open, the power equipped vehicles refer to Personal Settings in the locks will not operate.
Page 30
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Within 30 seconds, press the driver’s door lock switch has been shifted into the Park position after the vehicle in the LOCK direction. has been driven (shifted out of Park and all doors closed). 6.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 5. Within 30 seconds, press the driver’s door lock switch NOTE: Use the Auto Door Locks and Auto Unlock in the UNLOCK direction. features in accordance with local laws. 6. A single chime will sound to indicate the feature has WINDOWS been changed.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Vent Windows — If Equipped Power Windows — If Equipped Switches on the driver’s door trim panel let the driver You can control either front window using switches on operate the two vent windows from the front seat. the driver’s door trim panel.
Page 33
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Auto Down Feature — If Equipped Wind Buffeting The driver’s window switch has an auto down feature. Wind buffeting can be described as the perception of Press the window switch past the detent, release, and the pressure on the ears or a helicopter type sound in the window will go down automatically.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SLIDING SIDE DOOR To keep your door operating properly, observe the fol- The sliding door may be opened from the inside or the lowing guidelines: outside. Pull out on the outside handle to open the •...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 NOTE: The driver’s side sliding door cannot be opened 4. A single chime will sound to signify that you have while the fuel door is open. This feature operates only successfully completed the programming. when the sliding door is fully closed prior to opening the You can turn the feature back on by repeating the above fuel door.
Page 36
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The power sliding door may also be opened by pressing There are power sliding door switches located on the the switches on the overhead console or the switch trim panel just in front of the power sliding door for the located on the trim panel just in front of the sliding door.
Page 37
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 • If the power sliding door is not in the full open or close If the inside or outside door handles are used while the power sliding door is activated, the power sliding door position, it will fully open when a power sliding door feature will be canceled and the door must be opened or switch is pressed.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Protection Door Lock To provide a safer environment for small children riding in the rear seats, the sliding doors are equipped with a child protection door lock system. NOTE: When the child lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position.
Page 39
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 NOTE: WARNING! • After engaging the child protection door lock system, always test the door from the inside to make certain it To avoid trapping anyone in the vehicle in a colli- is in the desired position.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: To open the liftgate, insert the key into the lock and turn • After setting the child protection door lock system, to the right. On vehicles equipped with power locks the always test the door from the inside to make certain it liftgate can also be unlocked using the remote keyless is in the desired position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 NOTE: On vehicles without power locks, the liftgate can only be opened using the vehicle keys. The key must be held in the unlocked position for the liftgate to open. Power Liftgate — If Equipped The power liftgate may be opened manually or by using the button on the remote keyless entry transmitter.
Page 42
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The power liftgate may also be opened by pressing the WARNING! button located on the overhead console. During power operation, personal injury or cargo damage may occur. Ensure the liftgate travel path is clear.
Page 43
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 • The power liftgate must be in the full open or close • If the power liftgate encounters multiple obstructions positions for any of the buttons to operate. If the within the same cycle, the system will automatically liftgate is not in the full open or close positions it must stop and must be opened or closed manually.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Gas props support the liftgate in the open position. CAUTION! However, because the gas pressure drops with tempera- ture, it may be necessary to assist the props when The storage bin cover must lay flat and latched to opening the liftgate in cold weather.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Reinstalling Storage Bin Cover Emergency Release If the storage bin cover strap disengages from the latch, it can be reinstalled by inserting the loose end of the strap into the latch mechanism. Storage Bin Cover Emergency Release Strap NOTE: In the event of an individual being locked inside the storage bin, the storage bin cover can be opened from...
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Push the strap into the latch mechanism until it engages OCCUPANT RESTRAINTS around the latch post. Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and front passenger, driver inflatable knee blocker and if equipped, window bags for...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 of the worst injuries happen when people are thrown WARNING! from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the In a collision, you and your passengers can suffer inside of the vehicle.
Page 48
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! • It is extremely dangerous to ride in a cargo area, • Wearing a seat belt incorrectly is dangerous. Seat inside or outside of a vehicle. In a collision, belts are designed to go around the large bones of people riding in these areas are more likely to be your body.
Page 49
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is near the seatback of the front seats and next to your arm in the rear seats. Grasp the latch plate and pull out the belt.
Page 50
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch WARNING! plate into the buckle until you hear a “click”. • A belt that is buckled into the wrong buckle will not protect you properly.
Page 51
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 4. Position the lap belt across your thighs, below your WARNING! abdomen. To remove slack in the lap belt portion, pull up • A lap belt worn too high can increase the risk of on the shoulder belt.
Page 52
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. downward to help position the belt away from your The belt will automatically retract to its stowed position. neck. The upper anchorage can be adjusted upward by If necessary, slide the latch plate down the webbing to pushing anywhere on the anchorage.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 As a guide, if you are shorter than average, you will 4. Continue to slide the latch plate up until it clears the prefer a lower position, and if you are taller than average, folded webbing.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: These devices are not a substitute for proper seat WARNING! belt placement by the occupant. The seat belt still must be • A lap belt worn too loose or too high is dangerous. worn snugly and positioned properly.
Page 55
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 chime and flash the Seat Belt Warning Light for 96 1. With all doors closed and the ignition switch in any seconds or until the driver’s or front passenger’s seat belt position except On or Start, buckle the driver’s seat belt. is buckled.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Enhanced Warning System (BeltAlert) can be reacti- Seat Belt Extender vated by repeating this procedure. If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if NOTE: Although the Enhanced Warning System equipped) is in its lowest position, your dealer can...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 Driver And Front Passenger Supplemental Restraint Systems (SRS) — Airbags This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel.
Page 58
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The front airbags have a multi stage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size. Also, the front passenger airbag is certified to the Federal regulations that define Occupant Classification (Refer to “Occupant Classification System”...
Page 59
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 NOTE: Do not use a clothing bar mounted to the coat WARNING! hooks in this vehicle. A clothing bar will impede the • Do not put anything on or around the airbag proper performance of the window bags.
Page 60
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The passenger front airbag may not deploy even Infants in rear facing child restraints should NEVER ride when the driver front airbag has if the Occupant Classi- in the front seat of a vehicle with a passenger front airbag. fication System (refer to “Occupant Classification Sys- An airbag deployment can cause severe injury or death to tem”...
Page 61
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 You should read the instructions provided with your WARNING! child restraint to make sure that you are using it properly. • Relying on the airbags alone could lead to more 2. All occupants should wear their lap and shoulder severe injuries in a collision.
Page 62
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Driver Inflatable Knee Blocker Airbag System Components The airbag system consists of the following: • Front Passenger Seat Occupant Classification System • Occupant Restraint Controller (ORC) (OCS) — If Equipped • AIRBAG Light −...
Page 63
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 proper rate of inflation. The front airbag inflators are first turned on. After the self-check, the AIRBAG designed to provide different rates of airbag inflation. warning light will turn off. The PAD indicator light will function normally (Refer to “Passenger Airbag •...
Page 64
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Driver and Passenger Airbag/Inflator Units are • The Side Impact SRS Side Curtain Bags are designed located in the center of the steering wheel and the right to activate only in certain side collisions. When the side of the instrument panel.
Page 65
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 • When the ORC and the side impact sensors (with side classify an occupant into a size category based on impact option) detects a collision requiring the Driver sensor readings from within the seat cushion. Occu- Inflatable Knee Blocker, it signals the inflator unit.
Page 66
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE and cushion needs to be serviced in any way (includ- placed on the seat, the light will remain OFF. (The PAD ing removal or loosening/tightening of seat attach- indicator light is an amber light located on the center of ment bolts), take the vehicle to your authorized dealer.
Page 67
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 • The Occupant Classification Module (OCM) — If indicator light comes on when an adult is in the passen- ger seat, have the passenger re-position themselves in the Equipped is located beneath the front passenger seat. seat until the light goes out.
Page 68
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE turned OFF. When the OCS system detects an adult the (OCS) to properly classify the front passenger and calcu- PAD indicator light will be off, and the airbag will be late the proper airbag deployment. Do not make any enabled.
Page 69
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 • At no time should any supplemental restraint system The following requirements must be strictly adhered to: (SRS) component or SRS related component or fas- • Do not modify the front passenger seat assembly or tener be modified or replaced with any part except components in any way.
Page 70
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision which deploys the airbags, any irritation, move to fresh air. If the irritation continues, or all of the following may occur: see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instruc- •...
Page 71
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Enhanced Accident Response Maintaining Your Airbag System If the airbags and seat belt pretensioners deploy after an impact and the electrical system remains functional, WARNING! vehicles equipped with power door locks will unlock •...
Page 72
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The AIRBAG light does not come on or flickers during WARNING! the 6 to 8 seconds when the ignition switch is first • You need proper knee impact protection in a turned on.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 In the event that an investigation is undertaken by Event Data Recorder (EDR) In the event of an airbag deployment, your vehicle is DaimlerChrysler Corporation (regardless of initiative), designed to record up to 2-seconds of specific vehicle the company or its designated representative will first data parameters (see list below) in an event data recorder obtain permission of the appropriate custodial entity for...
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Airbag deployment level (if applicable) 1. Used for research purposes, such as to match data with a particular crash record in an aggregate database, • Seatbelt status provided confidentiality of personal data is thereafter •...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 To obtain Integrated Child Seat replacement WARNING! instructions: Use the order form at the back of this manual and specify In a collision, an unrestrained child, even a tiny publication number 81-016-1950. baby, can become a missile inside the vehicle.
Page 76
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Safety • Rearward-facing child seats must NEVER be used in experts recommend that children ride rearward-facing in the vehicle until they are at least the front seat of a vehicle with a front passenger one year old and weigh at least 20 lbs (9 kg).
Page 77
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 child’s back is against the seat back, they should use a and use the lap belt. Never allow a child to put the belt-positioning booster seat. The child and booster seat shoulder belt under an arm or behind their back. are held in the vehicle by the lap/shoulder belt.
Page 78
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips on getting the most out of your child shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt restraint: tight, however, any seat belt system will loosen with •...
Page 79
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 • Buckle the child into the seat according to the child center seating position. restraint manufacturer’s directions. • When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Don’t leave it loose in the vehicle.
Page 80
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When using the tether anchorages in the outboard seat- ing positions, ensure that the strap is routed over the top of the seatback and under the head restraint between the head restraint posts. Except for bench seats with split seatbacks, when the tether anchorage is used in the center seating position, the strap should be positioned straight over the top of the seatback.
Page 81
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Fleet vehicles equipped with the LATCH system on the WARNING! 3-passenger bench seat must have the seat adjusted to the full rear position on the tracks when the LATCH system An incorrectly anchored tether strap could lead to is used.
Page 82
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seat belt is tucked behind the child restraint and out of WARNING! reach. If the buckled seat belt interferes with the child restraint installation, instead of tucking the seat belt Fleet Vehicles Only: behind the child restraint, route the seat belt through the Do not install child restraint systems equipped with child restraint belt path and then buckle it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 In general, you will first loosen the adjusters on the lower Transporting Pets straps and tether straps so that you can more easily attach Airbags deploying in the front seat could harm your pet. the hook or connector to the lower anchorages and tether An unrestrained pet could be thrown about and possibly anchorages.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE infant carrier in a vehicle without rear seats. In an Restraining Infants and Small Children with Seat accident, serious injury or death may occur from the Delete Feature (Commercial Vehicles Only) deploying passenger air bag. There are different sizes and types of restraints for children from newborn size to the child almost large This vehicle is equipped with a child restraint tether...
Page 85
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 FACING TO THE REAR IN A VEHICLE EQUIPPED 1. Locate the child restraint tether anchor on the floor WITH THE REAR SEAT DELETE FEATURE (Com- just behind the front passenger seat. mercial Vehicles Only). When a convertible seat is properly installed forward facing, the vehicle seat should be adjusted to the rear most position.
Page 86
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Extend the child restraint tether anchor forward to- 3. Follow the child restraint manufacturer’s directions wards the front passenger seat. for proper use of connecting the child restraint to the extended tether strap. 4.
Page 87
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 7. Following the child seat manufacturer’s instructions, tighten the child restraint tether strap. 8. If necessary, reposition the seat head restraint. 9. Inspect the tether anchor strap for nicks, abrasions, discoloration, and loose threads. If these, or any other condition that might effect the performance of the strap is observed, USE.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE While cruising, brief full-throttle acceleration, within the WARNING! limits of local traffic laws, contributes to a good break-in. Wide open throttle acceleration in low gear can be The vehicle tether anchor is designed to be used detrimental and should be avoided.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 SAFETY TIPS WARNING! Exhaust Gas If you are required to drive with the deck lid / liftgate open, make sure that all windows are closed, WARNING! and the climate control blower switch is set at high speed.
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Light lodged in the tread. Inspect tread and sidewall for cuts or The light should come on and remain on for 6 to 8 cracks. Check wheel nuts for tightness, and tires (includ- seconds as a bulb check when the ignition switch is first ing spare) for proper pressure.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Annoying headlight glare can be reduced by moving the small control under the mirror to the night position Inside Day/Night Mirror (toward rear of vehicle). The mirror should be adjusted Adjust the mirror to center on the view through the rear while set in the day position (toward windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Driver’s Side Outside Mirror Auto Dimmer — If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Folding Outside Mirrors — If Equipped WARNING! Turn the power mirror switch knob all the way down to the left or right to fold in the mirrors. Turn the knob back Vehicles and other objects seen in a passenger side upward to the left mirror, right mirror, or off (center) convex mirror will look smaller and farther away position to the normal (unfolded) driving position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 Heated Remote Control Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the Rear Window Defrost. Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is on the sun visor.
UConnect™ system. The UConnect™ system phone equipped with the Bluetooth Hands-Free Profile, allows up to seven cellular phones to be linked to system. version 0.96 or higher. See www.chrysler.com/uconnect Only one linked (or paired) cellular phone can be used for supported phones.
Voice commands can be used to operate the UConnect™ Free Profile certified Bluetooth™ cellular phone. See system and to navigate through the UConnect™ menu www.chrysler.com/uconnect for supported phones. If structure. Voice commands are required after most your cellular phone supports a different profile (e.g., UConnect™...
Page 102
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Prior to giving a voice command, one must wait for Voice Command Tree the voice on beep, which follows the Ready prompt Refer to “Voice Tree” at the end of this section. or another prompt.
Page 103
• After the Ready prompt and the following beep, say phone equipped with the Bluetooth Hands-Free Profile, Setup Phone Pairing and follow the audible prompts. version 0.96 or higher. See www.chrysler.com/uconnect • When prompted, after the voice on beep, say Pair a for supported phones.
Page 104
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will then be asked to give your cellular phone a • System will prompt you to say the number you want priority level between 1 and 7, 1 being the highest call.
Page 105
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 • When prompted, say the name of the new entry. Use of you can say John Doe, where John Doe is a previ- ously stored name entry in the UConnect™ phone- long names helps the voice recognition and is recom- book.
Page 106
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE four associated phone numbers and designations. Each After you are finished editing an entry in the phonebook, language has a separate 32-name phonebook accessible you will be given the opportunities to edit another entry only in that language.
Page 107
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 • After you enter the Phonebook Delete menu, you will Delete All Entries in the UConnect™ Phonebook then be asked for the name of the entry that you wish • Press the ’Phone’ button to begin. to delete.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To call one of the names in the list, press the Voice Answer or Reject an Incoming Call - No Call Recognition’ button during the playing of the desired Currently in Progress name, and then say Call.
Page 109
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Making a Second Call while Current Call in indicating that the active and hold status of the two calls Progress have switched. Only one call can be placed on hold at one To make a second call while you are currently in a call, time.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After ignition key is switched off, a call can continue Call Termination To end a call in progress, momentarily press the Phone’ on the UConnect™ system either until the call ends or button.
Page 111
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 • After the Ready prompt and the following beep, say If the phone is not reachable and the UConnect™ system the name of the language you wish to switch to is operational, you may reach the emergency number as (English, Espanol, or Francais, if so equipped).
Page 112
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE emergency situations when the cell phone has network Paging coverage and stays paired to the UConnect™ system. To learn how to page, refer to Working with Automated Systems. Paging works properly except for pagers of Towing Assistance certain companies which time-out a little too soon to If you need towing assistance,...
Page 113
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 When calling a number with your UConnect™ system Turning Confirmation Prompts On/Off that normally requires you to enter in a touch-tone Turning confirmation prompts off will stop the system sequence on your cellular phone keypad, you can push from confirming your choices (e.g., the UConnect™...
Page 114
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dialing Using the Cellular Phone Keypad Mute/Un-mute (Mute off) You can dial a phone number with your cellular phone When you mute the UConnect™ system, you will still be keypad and still use the UConnect™ system (while able to hear the conversation coming from the other dialing via the cell phone keypad, the user must exercise party, but the other party will not be able to hear you.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Information Service If you would like to connect or disconnect the Blue- When using AT&T Wireless Service, dialing to phone tooth™ connection between a UConnect™ paired cellular number #121, you can access voice activated automated phone and the UConnect™...
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Select another Cellular Phone Delete UConnect™ Paired Cellular Phones This feature allows you to select and start using another • Press the ’Phone’ button to begin. phone with the UConnect™ system. The phone must •...
Page 117
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 training mode, follow one of the two procedures: From Voice Recognition (VR) outside the UConnect mode (e.g. from radio mode), • Always wait for the beep before speaking. • Press and hold the ‘Voice Recognition’ button for 5 •...
Page 118
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Even though the system is designed for users speaking • Even though international dialing for most number in North American English, French, and Spanish ac- combinations is supported, some shortcut dialing cents, the system may not always work for some. number combinations may not be supported.
Page 119
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 • Performance, such as audio clarity, echo, and loudness Power-Up to a large degree rely on the phone and network, and After switching the ignition key from OFF to either ON not the UConnect™ system. or ACC position, or after a reset, you must wait at least five (5) seconds prior to using the system.
Page 120
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 121
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121...
Page 122
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 SEATS North American English Primary Alternate(s) Manual Front & Second Row Seat Adjuster Phone pairing Pairing The adjusting bar is located under the front of the seat. Pull the bar up and move the seat to the desired position. Phonebook Phone book Release the bar to lock the seat into position.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched. WARNING! Adjust the seat only while the vehicle is parked. Adjusting a seat while the vehicle is moving is dangerous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped You may choose LOW, HIGH or No Heat. The switch This feature heats the front driver and passenger seats. position as well as an indicator light will show when the The controls for the heated seats are located on the LOW or HIGH heat is ON.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Manual Reclining Seats — If Equipped The recliner mechanism control is on the outboard side of the seat. To recline, lean forward slightly, lift the lever, then push back to the desired position and release the lever.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or fatally injured. Use the recliner only when the vehicle is parked.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Middle Rear Bench Seat Recline — If Equipped Stow ’n Go Seating — If Equipped Pull up on the handle located on the side of the seat to On vehicles equipped with Stow ’n Go seating, the release the seatback.
Page 130
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Fold Second Row Seats 1. Lower the head restraint and raise the armrests on the second row seat. 2. Slide storage bin locking mechanism to the Locked position and then pull up on the storage bin latch to open cover.
Page 131
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Second Row Seatback Release Lever Second Row Seat Release Strap NOTE: The cupholder must be in the closed position 5. Close the storage bin cover. before the seat can be tumbled into the floor. 4.
Page 132
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! NOTE: The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover. To Unfold Second Row Seats 1.
Page 133
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 2. Pull release strap marked “1” located on the rear of the seat to lower the seatback. Second Row Seatback Release Lever 4. Close the storage bin cover and adjust the head restraint to the desired position. Third Row Seatback Release Strap 1 To Fold Third Row Seats 1.
Page 134
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull release strap marked “2” to release the anchors. Third Row Seat Release Strap 3 To Unfold Third Row Seats Third Row Seatback Release Strap 2 4. Pull release strap marked “3” and tumble the seat 1.
Page 135
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Third Row Seatback Lift Assist Strap Third Row Seat Release Strap 3 2. Pull release strap marked “1” to unlock the recliner. 4. Adjust the head restraint to the desired position. 3. Pull release strap marked “3” to return the seatback to its full upright position.
Page 136
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments. Always be sure the seats are fully latched. Tailgate Mode 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 WARNING! To avoid serious injury or death, never operate the vehicle with occupants in the third row seat, while in the tailgate mode. Easy Access Seating The passenger’s and driver’s side second row seats can be tilted forward for easy access to the third row seat or rear cargo area.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To tilt the seat on vehicles equipped with Stow ’n Go WARNING! seating, pull forward on the release strap located on the front of the seat between the seat back and seat cushion In the event of a collision you could be injured if the and tilt the seat fully forward.
Page 139
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Seatback Release Lever Seat Release Handle 4. Pull up on the release handle and tumble the seat fully forward.
Page 140
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Pull the release bar located at the bottom front edge of To reinstall the seat, remove any obstructions from the the seat to disengage the front attachments. floor in front of the seat and ensure the head restraint is in its full downward position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 2. Pull up on release lever “2” and tumble the seat fully 50/50 Fold & Tumble Rear Seat Removal forward. 1. Lower the head restraint and pull up on release lever “1” to fold the seatback down. 50/50 Seat Release Lever 2 Location 50/50 Seat Release Lever 1 Location...
Page 142
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull the release strap “3” located at the bottom of the To reinstall the 50/50 rear seat, lower the head restraint to seat to disengage the front attachments. the full down position, tilt the seat forward and engage the front floor attachments, then tilt the seat rearward to engage the rear attachments.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 2 – Passenger and 3 – Passenger Bench Seats Release levers are located on the rear leg assemblies, near the floor. To remove the seat, squeeze each release handle and rotate downwards to deploy the wheels. A lock indicator button pops up when the seat is unlocked.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If not properly latched, the bench seats could be- come loose. Personal injuries could result. After reinstalling these seats, be sure the red indicator button on the release handles return into the handles.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Rear Seat Descriptions 7 Passenger Model — 2– passenger bench or bucket seats in the second position and 3– passenger bench seat or 50/50 bench seat in the third position. All rear seats are removable.
Page 146
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Normal Seating— 3. Additional Storage— The 2nd and 3rd row seats are installed. The 3rd row The 2nd and 3rd row seats installed. The 3rd row bench bench seat is in the full rear position on the tracks. seat is in the full forward position on the tracks and one or both of the rear seatbacks are folded down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Rear Quad and 50/50 Seating Flexibility 2. Increased Storage— The seats may be used with either or both seatbacks Increased storage area is provided by folding either or both seatbacks. With one seatback folded forward, rear folded forward for additional storage space, or with either or both seats removed from the vehicle.
Page 148
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: 4. Auxiliary Seating— Driving with the 2nd-row seats in the tumbled position is The 2nd row seats are removed from the vehicle. Then not recommended when passengers occupy the 3rd row the third row seats can be installed in either the rear or seats.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 TO OPEN AND CLOSE THE HOOD WARNING! To open the hood, two latches must be released. First pull • Not all head restraints in this vehicle are the the hood release lever located under the left side of the same.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Next, push to the left the safety catch located under the cm (12 inches) and then drop it. This should secure both front edge of the hood, near the center. latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 • A door, sliding door or the liftgate is left open. • Any overhead reading light is left on. • If the dimmer control is in the extreme top position. NOTE: The key must be out of the ignition switch or the ignition switch must be in the OFF position for this feature to operate.
Page 152
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dimmer Control Interior light Defeat (OFF) With the park lights or headlights Rotate the dimmer control to the on, rotating the dimmer control OFF position (extreme bottom). for the interior lights on the in- The interior lights will remain off strument panel upward will in- when the doors or liftgate are...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Automatic Headlights — If Equipped Daytime Running Lights (Canada/Fleet Vehicles This system automatically turns Only) your headlights ON or OFF based The Daytime Running Lights will come on whenever the on ambient light levels. To turn vehicle is running, the headlights are off, and the parking the system ON, turn the headlight brake is off.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE OFF or AUTO, the lights will turn off automatically until remain on. refer to Electronic Vehicle Information Center the next cycle of the ignition switch or headlight switch. (EVIC) “Customer Programmable Features” for more information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 MULTIFUNCTION LEVER Turn Signals Move the Multifunction Lever up or down and the arrows on each side of the base instrument cluster or Information Center flash to indicate proper operation of the front and rear turn signal lights. You can signal a lane change by moving the lever partially up or down.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlight Low/High Beam Selector Switch Pull the multifunction lever toward the steering wheel to switch the headlights between HIGH and LOW beam. Passing Light You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward the steer- ing wheel.
Page 157
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 wipers will operate for several seconds after the lever is Intermittent Wiper System released, and then resume the intermittent interval pre- Use the intermittent wipers when weather conditions viously selected. make a single wiping cycle, with a variable pause be- tween cycles, desirable.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN — IF EQUIPPED WARNING! To tilt the column, pull the small lever, located behind the turn signal control, toward you and move the wheel up Tilting the steering column while the vehicle is or down, as desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 NOTE: • The Traction Control System indicator comes on each time the ignition switch is turned ON. This will occur even if you used the switch to turn the system OFF. • The Traction Control will make buzzing or clicking sounds when in operation.
Page 160
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the driver selects Reverse the system scans for The warning display contains two sets of yellow and red objects behind the vehicle using four sensors located in LEDs, one set to warn of obstacles behind the left rear of the rear bumper.
Page 161
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 WARNING DISPLAY DISTANCES DISPLAY LED OBSTACLE DISTANCE FROM: LED COLOR AUDIBLE SIGNAL REAR CORNERS REAR CENTER 1st LED 59 in. (150 cm) Yellow None 2nd LED 47 in. (120 cm) Yellow None 3rd LED 39 in.
Page 162
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • • To avoid vehicle damage the Rear Park Sense Drivers must be careful when backing up even when using the Rear Park Sense System. Always System should only be used as a parking aid and check carefully behind your vehicle, and be sure to is unable to recognize every obstacle, including check for pedestrians, animals, other vehicles, ob-...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 NOTE: • Ensure that the rear bumper is free of dirt and debris to keep the system operating properly. • Jackhammers, large trucks, and other vibrations could affect the performance of the system. If “Service Park Sense System”...
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The pedals can be adjusted while driving. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the accelerator • The pedals cannot be adjusted when the vehicle is in R operation at speeds greater than 30 mph (50 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 To Activate: To Set At A Desired Speed: Push the “ON/OFF” button once and the CRUISE indi- When the vehicle has reached the desired speed, press cator located below the instrument cluster odometer will and release the “SET”...
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Vary the Speed Setting: To Accelerate For Passing: When the speed control is set, speed can be increased by Depress the accelerator as you would normally. When the pressing and holding the “RESUME/ACCEL” button. pedal is released, the vehicle will return to the set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 WARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy/Reading Lights Sunglass Storage At the rear of the overhead console, a compartment is At the forward end of the console are two courtesy/ provided for the storage of two pair of sunglasses. reading lights.
Page 169
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 Automatic Compass Calibration buttons for 10 seconds. Release the RESET button and This compass is self calibrating which eliminates the complete three 360° turns in an area free from large metal need to manually set the compass. When the vehicle is objects.
Page 170
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Compass Variance Compass Variance is the difference between magnetic North and Geographic North. In some areas of the country, the difference between magnetic and geographic North is great enough to cause the compass to give false readings.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 To set the variance: Turn the ignition switch ON and set Mini-Trip Computer the display to Comp/Temp. On vehicles equipped with a This displays information on the following: Compass/Mini Trip Computer press the RESET button •...
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Step Button Electronic Vehicle Information Center (EVIC) — If Push this button to cycle through all the Compass/Mini- Equipped trip Computer displays. The Electronic Vehicle Information Center, when the appropriate conditions exist, displays the following •...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 • CHECK TPM SYSTEM (Refer to ”Tire Pressure Moni- Customer Programmable Features — If Equipped tor System” in the “Starting And Operating, Tire Press the “MENU” button until one of the display choices Section”) following appears: •...
Page 174
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE US or Metric Use Factory Settings Pressing the “STEP” button when in this display selects If “Yes” is selected, all of the customer programmable US or Metric. The overhead console and climate control features will be set to the factory default and not dis- displays will be in the selected units.
Page 175
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 Remote Unlock Driver’s Door 1st If this feature is not selected, the driver’s seat, driver’s When this feature is selected only the driver’s door will mirror, adjustable pedals, and radio settings can only unlock on the first press of the remote keyless entry return to their memory set positions using the memory unlock button and require a second press to unlock the...
Page 176
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Flash Lights On Lock/Unlock? 30, 60, or 90 seconds, or not remain on. Pressing the When this feature is selected, the front and rear turn “STEP” button when in this display will select 30, 60, 90, signals will flash when the doors are locked or unlocked or “OFF.”...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 radio, power vent windows, power outlets, and remov- WARNING! able center console, when the ignition switch is turned off or until the key is removed and either front door is A moving garage door can cause injury to people and opened.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming HomeLink WARNING! NOTE: When programming a garage door opener, it is Vehicle exhaust contains carbon monoxide, a danger- advised to park outside the garage. Some vehicles may ous gas. Do not run the vehicle’s exhaust while require the ignition switch to be turned to the second training the transceiver.
Page 179
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 3. Simultaneously press and hold both the HomeLink button that you want to train and the hand-held trans- mitter buttons. Do not release the buttons until Step Four has been completed. NOTE: Some gate operators and garage door openers may require you to replace this Programming Step 3 with procedures noted in the Gate Operator/Canadian Pro- gramming section.
Page 180
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: To program the remaining two HomeLink but- 2. Firmly press and release the learn or smart button. tons, begin with Programming Step Two. Do not repeat (The name and color of the button may vary by manu- Step One.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 successfully been accepted by HomeLink. (The indicator Canadian Programming/Gate Programming Canadian radio-frequency laws require transmitter sig- light will flash slowly and then rapidly.) Proceed with nals to time-out (or quit) after several seconds of Programming Step Four to complete.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Press and hold the two outer HomeLink buttons until Security the indicator light begins to flash-after 20 seconds. If you sell your vehicle, be sure to erase the frequencies Release both buttons. Do not hold for longer that 30 by following the “Erasing HomeLink Buttons”...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 In the event that you are still having programming Press and hold the switch rearward to fully open the difficulties, questions, or comments, contact HomeLink sunroof. The sunroof can be stopped at any position at: www.homelink.com or 1-800-355-3515.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To close the sunroof, hold the switch in the forward WARNING! position. Again, any release of the switch will stop the movement and the sunroof will remain in a partial open In an accident, there is a greater risk of being thrown condition until the switch is pushed forward again.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The lower outlet is protected by an automatic reset circuit Electrical Outlet Use With Engine Off breaker. The automatic circuit breaker restores power when the overload is removed. The circuit breaker also CAUTION! supplies power to the outlet in the removable floor •...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 When the drawer is pulled out firmly, the arms of the CONVENIENCE TRAY DRAWER AND CUP HOLDERS cupholders will spring out. Place the container to be held into one of the cupholders and then push the arm toward Instrument Panel Cup Holders the container until the container is held stable.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Convenience Tray And Optional Smoker’s Rear Cupholders There are dual stationary cupholders located in the Package Kit Located between the instrument panel cupholders is a passenger side rear trim panel and a single stationary cup convenience tray that has been designed to hold miscel- holder on the driver side rear trim panel.
Page 189
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 • The quad seat cupholders are designed to break away if stepped on. To return the cupholder to its normal position, simply push the cupholder up to snap it into place. • The floor mat must be in position for optimum cup- holder operation.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE Second Row Seat Storage bins — If Equipped The Seat Storage Bins are located on the floor in front of Front Seat Storage Bin — If Equipped the second row seats, the area below the covers can be The storage bin is located under the front passenger’s used for storage when the second row seat is in the seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 Pull up on the storage bin latch to open the cover. Slide Overhead Rail System — If Equipped the storage bin locking mechanism to the Unlocked The overhead rail system contains provisions for three position to allow greater access to the storage bin.
Page 192
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Remove Storage Bins 1. Support the bin with one hand and pull the latch handles out. 3. Remove the storage bin. NOTE: Make sure the latch handle pops out before removing the storage bin. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 twist a ⁄ turn to attach the bin to the rail. Push the latch 1. Open the console lid and remove the storage tray. handle down to lock the storage bin in place. 2.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To reinstall the console, open the console lid and remove 2. Squeeze the legs together to disengage the holder from the storage tray. Pull up on the release handle and slide the floor console and remove the cell phone holder. the console forward to engage the front of the console To reinstall the cell phone holder, align the pivot legs into into the floor tray.
Page 195
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 Removable Floor Console Removable Floor Console Release Handle To remove the console use the following procedure: 3. Using the front and rear grab handles, slide the console rearward to disengage the front of the console 1.
Page 196
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To reinstall the console, remove the rubber mat and Cell Phone Holder relocate to the alternate floor tray, slide the console 1. Open the front lid and remove the cell phone holder forward to engage the front of the console into the floor by pulling rearward and up on the lower edge of the tray.
Page 197
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 2. Plug in the power cord for the cellular phone into the CAUTION! outlet located in the bottom of the forward console bin and reinstall the cell phone holder. • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not 3.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Compartment Storage Bins Cargo Area Storage Your vehicle may be equipped with open storage bins The seats in your vehicle are in-line which enables you to located in each rear trim panel. stow long objects, such as lumber or skis, on the floor without moving the seats.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 Rear Cargo Area Loading Limit Roof Rack ROOF LUGGAGE RACK — IF EQUIPPED Distribute cargo weight evenly on the roof rack crossbars. The crossbars and siderails are designed to carry the The roof rack does not increase the total load carrying weight on vehicles equipped with a luggage rack.
Page 200
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To move the cross bars, loosen the thumb screws located CAUTION! at the upper edge of each cross bar approximately six • turns, then move the cross bar to the desired position, Crossbars should remain equally spaced or parallel keeping the crossbars parallel to the rack frame.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 If the leveled vehicle is not moved for approximately 15 WARNING! hours, the leveling system will bleed itself down. The vehicle must be driven to reset the system. Cargo must be securely tied before driving your vehicle.
Page 203
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS ▫ AM Reception ..... . . 221 Instrument Panels And Controls ... . 208 ▫...
Page 205
UNDERSTANDING YOUR INSTRUMENT PANEL 205 ▫ Time Button ......231 ▫ Operating Instructions — Video Games/Camcorders ....242 ▫...
Page 206
206 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operating Instructions — Radio ... 258 ▫ Electronic Serial Number/Sirius Identification Number (ENS/SID) ....271 ▫...
Page 207
UNDERSTANDING YOUR INSTRUMENT PANEL 207 ▫ Automatic Temperature Control — Radio Operation And Cellular Phones ..274 If Equipped ......289 Remote Sound System Controls —...
UNDERSTANDING YOUR INSTRUMENT PANEL 211 one or more of your tires is significantly underinflated. INSTRUMENT CLUSTER DESCRIPTIONS Accordingly, when the low tire pressure telltale illumi- 1. Fuel Gauge nates, you should stop and check your tires as soon as The pointer shows the level of fuel in the fuel tank when possible, and inflate them to the proper pressure.
Page 212
212 UNDERSTANDING YOUR INSTRUMENT PANEL when a system fault is detected. The flash cycle will 3. Low Fuel Light repeat every ten minutes or until the fault condition is When the fuel level reaches approximately 3.0 removed and reset. gallons (11.0 liters) this light will turn on and remain on until fuel is added.
Page 213
UNDERSTANDING YOUR INSTRUMENT PANEL 213 6. Door Ajar Light The light will remain on until the cause is corrected. This light turns on if a door is not completely NOTE: The light may flash momentarily during sharp closed. cornering maneuvers which change fluid level condi- tions.
Page 214
214 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicles equipped with Anti-Lock brakes (ABS), are also 9. Airbag Light equipped with Electronic Brake Force Distribution (EBD). This light turns on and remains on for 6 to 8 In the event of an EBD failure, the Brake Warning Light seconds as a bulb check when the ignition will turn on along with the ABS Light.
Page 215
UNDERSTANDING YOUR INSTRUMENT PANEL 215 If the ABS light is on, the brake system should be serviced 13. Seat Belt Reminder Light as soon as possible to restore the benefits of Anti-Lock When the ignition switch is first turned ON, this brakes.
Page 216
216 UNDERSTANDING YOUR INSTRUMENT PANEL 15. Vehicle Theft Alarm Light — If Equipped CAUTION! This light will flash for approximately 15 sec- onds when the vehicle theft alarm is arming. Driving with a hot engine cooling system could damage your vehicle. If temperature gauge reads “H“, pull over and stop the vehicle.
Page 217
UNDERSTANDING YOUR INSTRUMENT PANEL 217 NOTE: You must apply the brakes before shifting from WARNING! Park. A hot engine cooling system is dangerous. You or 19. Oil Pressure Warning Light others could be badly burned by steam or boiling This light shows low engine oil pressure. The light coolant.
Page 218
218 UNDERSTANDING YOUR INSTRUMENT PANEL 21. Malfunction Indicator Light 22. Trac Off Indicator — If Equipped This light is part of an onboard diagnostic system This display indicator should illuminate for approxi- called OBD that monitors engine and automatic mately four seconds as a bulb check when the ignition transmission control systems.
Page 219
UNDERSTANDING YOUR INSTRUMENT PANEL 219 This is to prevent overheating of the brake system and is The trip odometer shows individual trip mileage. To a normal condition. The system will remain disabled for switch from odometer to trip odometer, press the Trip about 4 minutes until the brakes have cooled.
220 UNDERSTANDING YOUR INSTRUMENT PANEL 25. Trip Odometer Button Clock Setting Procedure Press this button to change the display from odometer to 1. Turn the ignition switch to the ON or ACC position trip odometer. The word TRIP will appear when in the and press the time button.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 you understand and save you concern about these “ap- AM Reception parent” malfunctions, you must understand a point or AM sound is based on wave amplitude, so AM reception two about the transmission and reception of radio sig- can be disrupted by such things as lightning, power lines nals.
222 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RAZ — AM/ FM STEREO RADIO Operating Instructions — Radio WITH CASSETTE TAPE PLAYER, CD PLAYER NOTE: Power to operate the radio is controlled by the AND CD CHANGER CONTROLS ignition switch. It must be in the ON or ACC position to NOTE: The radio sales code is located on the lower left operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 223 which are broadcasting this information. PTY (Program Tuning Press the TUNE control up or down to increase or Type) is used to characterize the station’s program ma- decrease the frequency. If you press and hold the button, terial, for example Rock Music .
Page 224
224 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Radio Display Program Type Radio Display Country Country Sports Sports Information Inform Talk Talk Jazz Jazz Top 40 Top 40 Foreign Language Language Weather Weather News News By pressing the SEEK button when the PTY icon is Nostalgia Nostalgia displayed, the radio will be tuned to the next frequency...
UNDERSTANDING YOUR INSTRUMENT PANEL 225 Pressing PTY, then SCAN will scan the FM Band and stop Tone Control at all RDS stations. Each RDS station will be played for a Slide the Bass and/or Treble controls up or down to 5 second scan once around the FM Band and stop at the adjust the sound for the desired tone.
226 UNDERSTANDING YOUR INSTRUMENT PANEL To stop the search, press SCAN a second time. To Change From Clock To Radio Mode Press the Time button to change the display between To Set The Radio Push-button Memory radio frequency and time. When you are receiving a station that you wish to commit to push-button memory, press the SET button.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 Press the SEEK button up or down to move the track Tape Eject number to skip forward or backward 1 to 6 selections. Press the EJT Tape button and the cassette will disengage Press the SEEK button once to move 1 selection, twice to and eject from the radio.
228 UNDERSTANDING YOUR INSTRUMENT PANEL Pinch Roller Release Operating Instructions — CD Player If ignition power or the radio ON/OFF switch are turned NOTE: The ignition switch must be in the ON or ACC off, the pinch roller will automatically retract to protect position and the volume control ON before the CD player the tape from any damage.
UNDERSTANDING YOUR INSTRUMENT PANEL 229 If the volume control is ON, the unit will switch from Seek Button radio to CD mode and begin to play. The display will Press the top of the SEEK button for the next selection on show the track number and index time in minutes and the CD.
230 UNDERSTANDING YOUR INSTRUMENT PANEL FF/TUNE/RW MODE Press FF (Fast Forward) and the CD player will begin to Press the MODE button to select between the tape player, fast forward until FF is released. The RW (Reverse) CD player, or satellite radio (if equipped). button works in a similar manner.
UNDERSTANDING YOUR INSTRUMENT PANEL 231 Disc Down/Program Button 5 Time Button Press this button to change the display from elapsed CD Press the DISC down (button 5) button to play the playing time to time of day. previous disc. Scan Button Seek Button Press this button to play the first 10 seconds of each track.
232 UNDERSTANDING YOUR INSTRUMENT PANEL • Water condensation on optics CD Diagnostic Indicators When driving over a very rough road, the CD player may SALES CODE REV — AM & FM STEREO RADIO skip momentarily. Skipping will not damage the disc or WITH CD PLAYER AND CD/DVD CHANGER the player, and play will resume automatically.
UNDERSTANDING YOUR INSTRUMENT PANEL 233 NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. PTY (Program Type) Pressing the INFO button once while in FM mode will turn on the PTY mode for 5 seconds.
Page 234
234 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Radio Display Program Type Radio Display Country Country Sports Sports Information Inform Talk Talk Jazz Jazz Top 40 Top 40 Foreign Language Language Weather Weather News News By pressing the SEEK button when the PTY icon is Nostalgia Nostalgia displayed, the radio will be tuned to the next frequency...
Page 235
UNDERSTANDING YOUR INSTRUMENT PANEL 235 Mode button. The frequency will be displayed and continu- Press the MODE button to select between, AM, FM, CD, ously updated while the button is pressed. CD/DVD changer or the Satellite Radio (if equipped). Balance When the Satellite Radio (if equipped) is selected “SA”...
Page 236
236 UNDERSTANDING YOUR INSTRUMENT PANEL To Set The Radio Push-Button Memory To Change From Clock To Radio Mode When you are receiving a station that you wish to Press the TIME button to change the display between commit to push-button memory, press the SET button. radio frequency and time.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 You may either insert or eject a disc with the radio OFF. CD Player Operation NOTE: If you insert a disc with the ignition ON and the radio • The ignition switch must be in the ON or ACC OFF, the display will show the time of day.
238 UNDERSTANDING YOUR INSTRUMENT PANEL EJT — Eject Press the SEEK button to move to the next randomly Press the EJT button and the disc will unload and move selected track. to the entrance for easy removal. The unit will switch to Press TUNE FF to fast forward through the tracks.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 • Maximum number of files: 255 Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 • Maximum number of folders: 100 file recording media and formats are limited. When • Maximum number of characters in file/folder names: writing MP3 files, pay attention to the following restric- tions.
Page 240
240 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 file formats 160, 128, 144, The radio will recognize only files with the *.mp3 exten- MPEG-2 Audio 112, 96, 80, 64, 24, 22.05, 16 sion as MP3 files. Non-MP3 files named with the *.mp3 Layer 3 56, 48, 40, 32, 24, extension may cause playback problems.
UNDERSTANDING YOUR INSTRUMENT PANEL 241 • Media - CD-RW media may take longer to load than INFO Button (CD Mode For MP3 Play) CD-R media Press and INFO button while playing MP3 disc. The radio scrolls through the following TAG information: •...
242 UNDERSTANDING YOUR INSTRUMENT PANEL DIR Button (CD Mode For MP3 Play) Operating Instructions — MP3 Player, Portable Press the DIR Button to display folders, when playing an Walkman MP3 discs that have a file/folder structure. Press DISC An MP3 player can be connected to the audio system. up (button 1) or DISC down (button 5) to move through Connect the cables to the RCA jacks located on the front the folders.
UNDERSTANDING YOUR INSTRUMENT PANEL 243 Listed below is the standard RCA SALES CODE RBQ — AM/FM STEREO RADIO Jack/Cable connection. You may also WITH 6 - DISC CD CHANGER want to refer to the manufacture’s NOTE: The radio sales code is located on the lower left instructions for the correct colors side of your radio faceplate.
244 UNDERSTANDING YOUR INSTRUMENT PANEL Radio Operation channel number will then be displayed for five seconds. The current channel name and number will then be Power/Volume Control displayed until an action occurs. CD’s may remain in the Press the PWR/VOL control to turn the radio on. Turn player while in the Satellite Radio mode.
Page 245
UNDERSTANDING YOUR INSTRUMENT PANEL 245 To Set The Radio Push-Button Memory Audio When you are receiving a station that you wish to The audio button controls the BASS, TREBLE, BAL- commit to push-button memory, press the SET RND ANCE, and FADE. button.
246 UNDERSTANDING YOUR INSTRUMENT PANEL Time Button CD Player Operation Press the TIME button to change the display between NOTE: The ignition switch must be in the ON or ACC radio frequency and time. position and the Power / Volume control pushed ON before the CD player will operate.
Page 247
UNDERSTANDING YOUR INSTRUMENT PANEL 247 If you insert a disc with the ignition ON and the radio Radio display will show “ejecting” when it is being ON, the unit will switch from radio to CD mode and ejected. begin to play when you insert the disc. The display will If you have ejected a disc and have not removed it within show the disc number, the track number, and index time 15 seconds, it will be reloaded.
Page 248
248 UNDERSTANDING YOUR INSTRUMENT PANEL Scan PTY (Program Type) Button Press the Scan button to scan through each track on the Pressing this button once will turn on the PTY mode for CD currently playing. 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn off.
Page 249
UNDERSTANDING YOUR INSTRUMENT PANEL 249 Program Type Radio Display Program Type Radio Display Information Inform Talk Talk Jazz Jazz Top 40 Top 40 Foreign Language Language Weather Weather News News By pressing the SEEK button when the PTY icon is Nostalgia Nostalgia displayed, the radio will be tuned to the next frequency...
Page 250
250 UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SCAN button when the PTY icon is As a safeguard and to protect your CD player, one of the displayed, the radio will stop at every PTY station on the following warning symbols may appear on your display. band and list each corresponding program type in the A CD HOT symbol indicates the player is too hot.
UNDERSTANDING YOUR INSTRUMENT PANEL 251 SALES CODE RBK — AM/ FM STEREO RADIO Radio Operation WITH CD PLAYER AND CD CHANGER Power/Volume Control CONTROLS Press the ON/VOL control to turn the radio on. Turn the NOTE: The radio sales code is located on the lower left volume control clockwise to increase the volume.
Page 252
252 UNDERSTANDING YOUR INSTRUMENT PANEL the radio will continue to tune until you release the both AM and FM. This allows a total of 10 AM and 10 FM button. The frequency will be displayed and continu- stations to be locked into push-button memory. The ously updated while the button is pressed.
UNDERSTANDING YOUR INSTRUMENT PANEL 253 Press the AUDIO button a third time and BAL will be General Information displayed. Press the SEEK + or SEEK – to adjust the This radio complies with Part 15 of FCC rules and with sound level from the right or left side speakers.
Page 254
254 UNDERSTANDING YOUR INSTRUMENT PANEL Inserting The Compact Disc Seek Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the CAUTION! beginning of the current selection, or return to the beginning of the previous selection if the CD is within the This CD player will accept 4 ⁄...
UNDERSTANDING YOUR INSTRUMENT PANEL 255 FF/TUNE/RW Satellite Radio (if equipped). When Satellite Radio (if Press FF (Fast Forward) and the CD player will begin to equipped) is selected “SAT” will appear in your radio fast forward until FF is released. The RW (Reverse) display.
Page 256
256 UNDERSTANDING YOUR INSTRUMENT PANEL Disc Up/Program Button 1 Random Play (RND) Press the DISC up (button 1) button to play the next Press the Random button to play the tracks on the available disc. selected disc in random order for an interesting change of pace.
UNDERSTANDING YOUR INSTRUMENT PANEL 257 As a safeguard and to protect your CD player, one of the SALES CODE RB1 — AM/FM STEREO RADIO following warning symbols may appear on your display. WITH DVD/GPS NAVIGATION SYSTEM A CD HOT symbol indicates the player is too hot. CD HOT will pause the operation.
258 UNDERSTANDING YOUR INSTRUMENT PANEL stereo radio with CD capability. Refer to your “Naviga- To manually set the clock, change the time zone, or change daylight savings information, use a ball point pen tion User’s Manual” for detailed operating instructions. or similar object to press the hour (H) or minute (M) NOTE: If your vehicle is not equipped with the CD buttons on the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 259 Changing Time Zone 4. Press ENTER. 1. Highlight “Clock Setup” and press ENTER. 5. Select “Done” when finished. 2. At the Clock Setup screen highlight the box next to 6. Select “Done” to exit from the clock setting mode. “Time Zone”...
260 UNDERSTANDING YOUR INSTRUMENT PANEL The CD/DVD Changer will play CD-R, CD-RW, CD- Operating Instructions — CD/DVD Changer Audio and DVD Video disc formats. The video screen Loading The CD/DVD Changer will turn on automatically once a DVD is inserted into the The premium version has a multi-disc changer, changer.
Page 261
UNDERSTANDING YOUR INSTRUMENT PANEL 261 which numbered position the disc will be loaded into. play from the menu options. The radio display will show The disc will automatically be pulled into the CD/DVD the chapter number and index time in hours and minutes changer.
262 UNDERSTANDING YOUR INSTRUMENT PANEL EJECT (EJT) Button If there is a disc in the changer, press the EJT button and the disc will eject. If you do not remove the disc within 10 seconds, it will be reloaded and the display will show PAUSE.
Page 263
UNDERSTANDING YOUR INSTRUMENT PANEL 263 Remote Control Buttons Remote Control Buttons 1. Headphone Transmitter 17. Enter 2. Menu Up/Next Track/Chapter 18. Light 3. Menu Left/Fast Rewind Headphone Transmitter Button (1) 4. Return The headphone transmitter button on the remote control 5.
Page 264
264 UNDERSTANDING YOUR INSTRUMENT PANEL RTN Button (4) PAUSE/PLAY Button (6) This button only functions in CD/DVD mode. Press this This button only functions in DVD video mode. Press this button to return to the previous menu when in the disc button once to pause the video, press a second time to menu mode.
Page 265
UNDERSTANDING YOUR INSTRUMENT PANEL 265 SLOW Button (12) chapter or track. Each press of the NEXT/PREV button This button only functions in DVD video mode. Press this up or down will toggle through the chapters or tracks. button to advance the video. If the DVD is paused, FF/RW Buttons (3, 16) pressing this button will advance the video frame by Press and hold FF (Fast Forward) once and the CD/DVD...
266 UNDERSTANDING YOUR INSTRUMENT PANEL Remote Control Battery Service • To replace the batteries for the remote control slide the cover rearward. The replacement batteries for the remote control are two AAA batteries. Operating Instructions — Video Screen Push up on the release button to lower the video screen. Lowering Video Screen...
Page 267
UNDERSTANDING YOUR INSTRUMENT PANEL 267 1. Screen Width Button Changes the width of the screen picture. 2. Enter Button This button will enter the selection from the on-screen menu. 3. Brightness Button Changes the brightness of the screen picture. Video Screen and Controls 1 —...
268 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Headphones Power Button Pressing the power button will turn the headphones ON/OFF. An indicator light will illuminate on the head- phone earpiece to indicate the headphones are ON. NOTE: • The headphones will turn off automatically in ap- proximately 3 minutes if they lose the signal form the system or when the radio or rear audio/video system is turned off.
Page 269
UNDERSTANDING YOUR INSTRUMENT PANEL 269 harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. If you do not hear sound coming from the headphones, check for the following conditions: 1. Rear Seat Audio/Video System and headphones are on.
270 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — MP3 Player, Portable Listed below is the standard RCA Jack/Cable connection. You may also Walkman An MP3 player can be connected to the audio system. want to refer to the manufacture’s Connect the cables to the RCA jacks located on the front instructions for the correct colors of the CD/DVD changer.
UNDERSTANDING YOUR INSTRUMENT PANEL 271 SATELLITE RADIO — IF EQUIPPED Electronic Serial Number/Sirius Identification Satellite radio uses direct satellite to receiver broadcast- Number (ENS/SID) ing technology to provide clear digital sound, coast to The Electronic Serial Number/Sirius Identification Num- coast. The subscription service provider is Sirius™ Satel- ber is needed to activate your Sirius Satellite Radio lite Radio.
272 UNDERSTANDING YOUR INSTRUMENT PANEL • After 3 seconds, the current channel name and channel ESN/SID Access With RBU, RAZ, RB1 and RBQ number will be displayed for 5 seconds. Radios With the ignition switch in the ACCESSORY position and •...
UNDERSTANDING YOUR INSTRUMENT PANEL 273 moving on to the next channel. The word SCAN will Using the PTY (Program Type) Button — If appear in the display between each channel change. Press Equipped the SCAN button a second time to stop the search. Follow the PTY button instructions that apply to your radio.
274 UNDERSTANDING YOUR INSTRUMENT PANEL • Dense tree coverage may interrupt reception in the PTY Button SEEK When the desired program is obtained, press the SEEK form of short audio mutes. button within five seconds. The channel will change to •...
UNDERSTANDING YOUR INSTRUMENT PANEL 275 The right hand rocker switch has a push button in the REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED center and controls the volume and mode of the sound The remote sound system controls are located on the rear system.
276 UNDERSTANDING YOUR INSTRUMENT PANEL Radio Operation CD Player Pressing the top of the switch will SEEK up for the next Pressing the top of the switch once will go to the next listenable station and pressing the bottom of the switch track on the CD.
UNDERSTANDING YOUR INSTRUMENT PANEL 277 2. Keep the cassette tape in its case to protect from turned all the way down. To prevent this, you should slackness and dust when it is not in use. periodically clean the head with a commercially available WET cleaning cassette.
278 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Do not use solvents such as benzine, thinner, cleaners, Manual Air Conditioning and Heating System or antistatic sprays. 5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7.
Page 279
UNDERSTANDING YOUR INSTRUMENT PANEL 279 mode. When the blower control is set to any position other than off, it selects the amount of air delivered to the passenger compartment. There are four blower speeds. The fan speed increases as you move the control clockwise.
280 UNDERSTANDING YOUR INSTRUMENT PANEL Front Mode Control Panel Mode The mode control allows you to choose from several patterns of air distribution. NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are iden- tified by the small dots.
Page 281
UNDERSTANDING YOUR INSTRUMENT PANEL 281 Air comes from the outlets in the instrument panel. Each Bi-Level Mode of these outlets can be individually adjusted to direct the flow of air. Moving the air vane knob on the center outlets down, will close off the air flow from the center outlets.
Page 282
282 UNDERSTANDING YOUR INSTRUMENT PANEL Air comes from both the instrument panel outlets, floor Floor Mode outlets and defrost. A slight amount of air is also directed through the side window demister outlets. NOTE: In many temperature lever positions, the bi- level mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets.
Page 283
UNDERSTANDING YOUR INSTRUMENT PANEL 283 Mix Mode Defrost Mode Mix Outlets Defrost Outlets Air comes from the floor, defrost and side window Air comes from the windshield and side window demist demist outlets. This mode works best in cold or snowy outlets.
284 UNDERSTANDING YOUR INSTRUMENT PANEL • If your air conditioning performance seems lower than NOTE: For improved safety, the compressor is activated and the recirculation mode is deactivated when Mix or expected, check the A/C air filter, if so equipped, and Defrost modes are selected.
Page 285
UNDERSTANDING YOUR INSTRUMENT PANEL 285 recirculation mode to rapidly cool the inside of the A/C Recirculation Programming vehicle. The recirculation mode can also be used to The recirculation control is programmed to cancel the temporarily block out outside odors, smoke, and dust. recirculation mode when the ignition key is turned OFF and will reset to outside air mode when the ignition key NOTE:...
286 UNDERSTANDING YOUR INSTRUMENT PANEL • Start the engine, and continue to hold in the “Rear Manual Rear Zone Climate Control — If Equipped Wipe/Wash” button until the indicator light starts The Manual Rear Zone Climate Control system has floor flashing repeatedly.
Page 287
UNDERSTANDING YOUR INSTRUMENT PANEL 287 Rear Blower Control The center knob on the front climate control unit has five The primary control for the rear blower is on the front positions, “REAR”, “OFF”, and a range of blower speeds. climate control unit located on the instrument panel. Only when the primary control for the rear blower is in the “REAR”...
Page 288
288 UNDERSTANDING YOUR INSTRUMENT PANEL in the cold position, cold air will be delivered from the CAUTION! headliner outlets. As the rear temperature knob is turned towards hot, the air will get warmer, and the Interior air enters the Manual Rear Zone Climate air will be delivered from both the headliner and floor Control system through an intake grille located in outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 289 The rear temperature knob and the rear blower speed can be adjusted as desired by the second seat occupants. Automatic Temperature Control — If Equipped The Infrared Three-Zone Automatic Temperature Control System automatically maintains the interior comfort level desired by the driver and all passengers.
Page 290
290 UNDERSTANDING YOUR INSTRUMENT PANEL front ATC unit is in the “AUTO” position. Once the To provide you with maximum comfort in the automatic desired temperature is displayed, the system will achieve mode, during cold start-ups the blower fan will remain and maintain that comfort level automatically.
Page 291
UNDERSTANDING YOUR INSTRUMENT PANEL 291 This feature may be enabled using the following proce- NOTE: Each of these features operate independently dure: from each other. If any one feature is controlled manually, the remaining features will continue to operate automati- •...
Page 292
292 UNDERSTANDING YOUR INSTRUMENT PANEL Panel Mode Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vane knob on the center outlets down, will close off the air flow from the center outlets.
Page 293
UNDERSTANDING YOUR INSTRUMENT PANEL 293 Bi-Level Mode Air comes from both the instrument panel outlets, floor outlets and defrost. A slight amount of air is also directed through the side window demister outlets. In many temperature positions, the bi-level NOTE: mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets.
Page 294
294 UNDERSTANDING YOUR INSTRUMENT PANEL Floor Mode Mix Mode Floor Outlets Mix Outlets Air comes from the floor outlets. A slight amount of air is Air comes from the floor, defrost and side window directed through the defrost and side window demister demist outlets.
Page 295
UNDERSTANDING YOUR INSTRUMENT PANEL 295 Defrost Mode of fog, mist, or ice on the windshield. Defrost mode must be manually selected to clear the windshield and side glass. The snowflake or a/c button allows the opera- tor to manually activate or deactivate the air conditioning system.
Page 296
296 UNDERSTANDING YOUR INSTRUMENT PANEL the recirculation button. The recirculation mode should The “REAR SYSTEM” knob for the Rear Automatic only be used temporarily. The recirculation symbol will Temperature Control System is on the front ATC control illuminate in the display when this button is selected. unit located on the instrument panel.
Page 297
UNDERSTANDING YOUR INSTRUMENT PANEL 297 you would like the system to maintain by pressing the Rear Temperature Control button. Once the desired tem- perature is displayed, the system will achieve and main- tain that comfort level automatically. When the system is set up for your comfort level, it is not necessary to change the settings.
Page 298
298 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Blower Control CAUTION! The rear blower control, located in the headliner near the center of Interior air enters the Rear Automatic Temperature vehicle “OFF”, Control System through an intake grille located in “AUTO” and a range of blower the passenger side trim panel behind the third seat.
Page 299
UNDERSTANDING YOUR INSTRUMENT PANEL 299 Rear Mode Control Bi-Level Mode The Rear Mode Control, located in Air comes from both the headliner outlets and the the headliner near the center of floor outlets. the vehicle can be used to select In many temperature positions, the bi-level NOTE: between Auto, Headliner, Bi-...
Page 300
300 UNDERSTANDING YOUR INSTRUMENT PANEL glycol antifreeze coolant in water is recommended. Refer system lubrication to minimize the possibility of com- to section 7, Maintenance Procedures, of this manual for pressor damage when the system is started again. proper coolant selection. Window Fogging Vehicle windows tend to fog on the inside in mild rainy Winter Operation...
UNDERSTANDING YOUR INSTRUMENT PANEL 301 Operating Tips A/C Air Filter — If Equipped On vehicles equipped with Automatic Temperature Con- trol (ATC), the climate control system filters out dust and pollen from the air. Refer to section 7 “Air Conditioning” for filter replacement instructions.
302 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Washer Operation — Manual Temperature Vehicles equipped with Automatic Temperature Control, the controls for these features are located in the middle of Control Only The controls are located on the Manual Tempera- the instrument panel above the radio. ture Control head above the front blower control.
UNDERSTANDING YOUR INSTRUMENT PANEL 303 Rear Wiper Operation — Automatic Temperature Rear Washer Operation — Automatic Control Only Temperature Control Only Press this button to have the rear wiper have a Press and hold the button as long as spray is continuous wipe.
304 UNDERSTANDING YOUR INSTRUMENT PANEL the reservoir with windshield washer solvent (not radia- The washer fluid reservoir will hold a full gallon of fluid tor antifreeze) and operate the system for a few seconds when the Low Washer Fluid Light illuminates. to flush out the residual water.
Page 305
UNDERSTANDING YOUR INSTRUMENT PANEL 305 If your vehicle is equipped with Infrared Three-Zone CAUTION! Automatic Temperature Control the rear defroster sym- bol will show in the display screen when the rear To avoid damaging the electrical conductors of the window defroster is on. rear window defroster, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window.
STARTING AND OPERATING 311 STARTING PROCEDURES WARNING! Before starting your vehicle, adjust your seat, adjust both • Be sure to turn off the engine if you want to rest or inside and outside mirrors, and fasten your seat belts. sleep in your car. Accidents can be caused by inadvertently moving the gear selection lever or by pressing the accelerator pedal.
312 STARTING AND OPERATING Automatic Transmission Extremely Cold Weather Starting (Below 20°F / The gear selector must be in the NEUTRAL or PARK –29°C) position before you can start the engine. Depress the Follow the same instructions in the “Normal Starting” brake pedal before shifting into any driving gear.
STARTING AND OPERATING 313 If Engine Fails To Start WARNING! If the engine fails to start after you have followed the “Normal Starting” procedure, it may be flooded. Push Never pour fuel or other flammable liquid into the the accelerator pedal all the way to the floor and hold it throttle body air inlet opening in an attempt to start there while cranking the engine.
314 STARTING AND OPERATING If the engine has been flooded, it may start to run, but not WARNING! have enough power to continue running when the key is released. If this occurs, continue cranking with the accel- Do not attempt to push or tow your vehicle to get it erator pedal pushed all the way to the floor.
STARTING AND OPERATING 315 ENGINE BLOCK HEATER — IF EQUIPPED AUTOMATIC TRANSMISSION The engine block heater warms engine coolant and permits quicker starts in cold weather. Connect the cord CAUTION! to a standard 110-115 volt AC electrical outlet with a grounded, three-wire extension cord.
316 STARTING AND OPERATING Automatic Transmission Ignition Interlock System WARNING! This system prevents the key from being removed unless the shift lever is in PARK. It also prevents shifting out of It is dangerous to shift the selector lever out of “P” or PARK unless the key is in the OFF or ON positions.
Page 317
STARTING AND OPERATING 317 Reset Mode - Electronic Transmission possible convenience. Your dealer has diagnostic equip- The transmission is monitored electronically for abnor- ment to determine if the problem could recur. mal conditions. If a condition is detected that could cause If the transmission cannot be reset, dealer service is damage, the transmission automatically shifts into sec- required.
Page 318
318 STARTING AND OPERATING vehicle under heavy loading conditions, (i.e. in hilly WARNING! terrain, traveling into strong head winds or while towing heavy trailers), using the “3” position will improve Never use Park position on an automatic transmis- performance and extend transmission life by reducing sion as a substitute for the parking brake.
STARTING AND OPERATING 319 occur only to prevent engine overspeed while downshifts occur earlier than other gear range selections. NOTE: The vehicle computer will over ride Overdrive and “3” Drive ranges by changing shift points if the transmission operating temperature exceeds acceptable limits.
Page 320
320 STARTING AND OPERATING Be sure the parking brake is firmly set when parked and WARNING! the gear shift lever is in the PARK position. When • Always fully apply the parking brake when leav- parking on a hill you should apply the parking brake before placing the gear shift lever in PARK, otherwise the ing your vehicle, or it may roll and cause damage load on the transmission locking mechanism may make it...
STARTING AND OPERATING 321 When parking on a hill, turn the front wheels toward the by increased pedal travel during application, greater curb on a downhill grade and away from the curb on an pedal force required to slow or stop, and potential uphill grade.
Page 322
322 STARTING AND OPERATING The ABS light monitors the Anti-Lock Brake WARNING! System. The light will come on when the • Anti-lock system (ABS) cannot prevent the natu- ignition switch is turned to the ON position and may stay on for as long as four seconds. ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- If the ABS light remains on or comes on while driving, it...
Page 323
STARTING AND OPERATING 323 • and a slight drop or fall away of the brake pedal at the When the vehicle is driven over approximately 7 mph (11 km/h), you may also hear a slight clicking sound as well end of the stop. as some related motor noises.
324 STARTING AND OPERATING TRACTION CONTROL — IF EQUIPPED The system is always in the “stand by” mode unless: • The Traction Control Switch has been used to turn the This system monitors the amount of wheel spin of each of the driven wheels.
STARTING AND OPERATING 325 • There is a Traction Control System malfunction POWER STEERING The standard power steering system will give you good • The system has been deactivated to prevent damage to vehicle response and increased ease of maneuverability the brake system due to overheated brake tempera- in tight spaces.
326 STARTING AND OPERATING DRIVING ON SLIPPERY SURFACES WARNING! Acceleration Continued operation with reduced power steering Rapid acceleration on snow covered, wet, or other slip- assist could pose a safety risk to yourself and others. pery surfaces may cause the front wheels to pull errati- Service should be obtained as soon as possible.
STARTING AND OPERATING 327 Traction TIRE SAFETY INFORMATION When driving on wet or slushy roads, it is possible for a Tire Markings wedge of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability.
Page 328
328 STARTING AND OPERATING • European Metric tire sizing is based on European • Temporary Spare tires are high-pressure compact design standards. Tires designed to this standard have spares designed for temporary emergency use only. the tire size molded into the sidewall beginning with Tires designed to this standard have the letter “T”...
Page 329
STARTING AND OPERATING 329 EXAMPLE: 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.5 = Section Width in Inches (in) R = Construction Code —...
330 STARTING AND OPERATING EXAMPLE: —The maximum speed corresponding to the Speed Symbol should only be achieved un- der specified operating conditions (i.e. tire pressure, vehicle loading, road conditions, and posted speed limits). Load Identification: ..blank..= Absence of any text on sidewall of the tire indicates a Standard Load (SL) Tire Extra Load (XL) = Extra Load (or Reinforced) Tire Light Load = Light Load Tire C,D,E = Load range associated with the maximum load a tire can carry at a specified pressure...
Page 331
STARTING AND OPERATING 331 EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation —This symbol certifies that the tire is in compliance with the U.S. Department of Transportation tire safety standards, and is approved for highway use. MA = Code representing the tire manufacturing location. (2 digits) L9 = Code representing the tire size.
332 STARTING AND OPERATING Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar. Tire and Loading Information Tire Placard Location...
Page 333
STARTING AND OPERATING 333 axles must not be exceeded. For further information on This placard tells you important information about GAWR’s, vehicle loading, and trailer towing, refer to the the: “Vehicle Loading” section of this manual. 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of...
Page 334
334 STARTING AND OPERATING 3. Subtract the combined weight of the driver and pas- manual to determine how this reduces the available sengers from XXX kilograms or XXX pounds. cargo and luggage load capacity of your vehicle. 4. The resulting figure equals the available amount of NOTE: The following table shows examples on how to cargo and luggage load capacity.
336 STARTING AND OPERATING 1. Safety— WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can cause increase your stopping distance. Use tires of the accidents.
STARTING AND OPERATING 337 2. Economy— Some vehicles may have Supplemental Tire Pressure Improper inflation pressures can cause uneven wear Information for vehicle loads that are less than the patterns to develop across the tire tread. These abnormal maximum loaded vehicle condition. These pressure con- wear patterns will reduce tread life resulting in a need for ditions will be found in the “Supplemental Tire Pressure earlier tire replacement.
Page 338
338 STARTING AND OPERATING The pressure should be checked and adjusted as well as Inflation pressures specified on the placard are always inspecting for signs of tire wear or visible damage at least “cold tire inflation pressure.” Cold tire inflation pressure once a month.
STARTING AND OPERATING 339 Example: If garage temperature = 68 °F (20 °C) and the WARNING! outside temperature = 32 °F (0 °C) then the cold tire inflation pressure should be increased by 3 psi (21 kPa), High speed driving with your vehicle under maxi- which equals 1 psi (7 kPa) for every 12 °F (7 °C) for this mum load is dangerous.
340 STARTING AND OPERATING Cuts and punctures in radial tires are repairable only in WARNING! the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs. Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph Compact Spare Tire —...
STARTING AND OPERATING 341 WARNING! CAUTION! The limited use spare tires are for emergency use Because of the reduced ground clearance, do not take only. Installation of this limited use spare tire affects your vehicle through an automatic car wash with the vehicle handling.
342 STARTING AND OPERATING WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) for more than 30 seconds continuously when you are stuck, and don’t let anyone near a spinning wheel, no matter what the speed.
STARTING AND OPERATING 343 Keep dismounted tires in a cool, dry place with as little Life of Tire The service life of a tire is dependent upon varying exposure to light as possible. Protect tires from contact factors including but not limited to: with oil, grease, and gasoline.
344 STARTING AND OPERATING WARNING! CAUTION! • Do not use a tire, wheel size or rating other than Replacing original tires with tires of a different size that specified for your vehicle. Some combina- may result in false speedometer and odometer read- tions of unapproved tires and wheels may change ings.
STARTING AND OPERATING 345 Improper alignment will not cause vehicle vibration. CAUTION! Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and To avoid damage to your vehicle or tires, observe the following precautions: avoid tire cupping and spotty wear.
346 STARTING AND OPERATING NOTE: In order to avoid damage to tires, chains, and Snow tires generally have lower speed ratings than what your vehicle do not drive for a prolonged period of time was originally equipped with your vehicle and should on dry pavement.
STARTING AND OPERATING 347 Section of this manual. More frequent rotation is permis- TIRE PRESSURE MONITOR SYSTEM (TPMS) — IF sible if desired. The reasons for any rapid or unusual EQUIPPED wear should be corrected prior to rotation being per- •...
348 STARTING AND OPERATING • The Tire Pressure Monitor System (TPMS) will warn Base Tire Pressure Monitoring System without the driver of a low tire pressure if the tire pressure falls Electronic Vehicle Information Center (EVIC) — If below the low pressure warning threshold for any Equipped reason, including low temperature effects.
STARTING AND OPERATING 349 NOTE: A low spare or compact tire pressure will not Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Lamp will cause the Tire Pressure Monitor System Telltale Lamp to illuminate in the instrument cluster and an audible illuminate or the chime to sound.
Page 350
350 STARTING AND OPERATING • Receiver Module Should this occur you should stop as soon as possible, check the inflation pressure of each tire on your vehicle, • 4 Tire Pressure Monitoring Sensors and inflate each tire to the pressure recommended by the •...
STARTING AND OPERATING 351 Service Tire System Soon CAUTION! The Tire Pressure Monitoring Telltale Lamp will flash on and off for 60 seconds in the instrument cluster, and an The Tire Pressure Monitoring System (TPMS) has audible chime will be activated when one or more of the been optimized for the original equipment tires and four active...
352 STARTING AND OPERATING • Driving on a significantly underinflated tire causes the CAUTION! tire to overheat and can lead to tire failure. Underin- flation also reduces fuel efficiency and tire tread life, After inspecting or adjusting the tire pressure al- and may affect the vehicle’s handling and stopping ways reinstall the valve stem cap.
STARTING AND OPERATING 353 Pressure Monitoring Lamp to be ON, and a Chime will United States ..... KR5S120123 sound. This sequence will repeat for every key cycle until Canada .
354 STARTING AND OPERATING Poor quality gasoline can cause problems such as hard Reformulated gasolines contain oxygenates, and are spe- starting, stalling and hesitations. If you experience these cifically blended to reduce vehicle emissions and im- symptoms, try another brand of “regular” gasoline be- prove air quality.
STARTING AND OPERATING 355 to reduce spark plug life and reduce emission system CAUTION! performance in some vehicles. The manufacturer recom- mends using gasolines without MMT. Since the MMT DO NOT use gasolines containing Methanol or E85 content of gasoline may not be indicated on the pump, Ethanol.
356 STARTING AND OPERATING • The use of fuel additives which are now being sold as Fuel System Cautions octane enhancers is not recommended. Most of these products contain high concentrations of methanol. CAUTION! Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not Follow these guidelines to maintain your vehicle’s the responsibility of the manufacturer.
STARTING AND OPERATING 357 • Do not inhale exhaust gases. They contain carbon ADDING FUEL monoxide, a colorless and odorless gas which can kill. Fuel Filler Cap (Gas Cap) Never run the engine in a closed area, such as a The gas cap is located behind the fuel filler door on the garage, and never sit in a parked vehicle with the left side of the vehicle.
Page 358
358 STARTING AND OPERATING NOTE: The driver’s side sliding door cannot be opened CAUTION! while the fuel door is open. This feature operates only when the sliding door is fully closed prior to opening the Damage to the fuel system or emission control fuel door.
STARTING AND OPERATING 359 • If the gas cap is not tighten properly, the Malfunction NOTE: When the fuel nozzle “clicks” or shuts off, the fuel tank is full. Indicator Light will come on. Be sure the gas cap is tightened every time the vehicle is refueled.
360 STARTING AND OPERATING • If the problem continues, the message will appear the next time the vehicle is started. See Section 7 of this manual for more information. Make sure that the fuel filler cap is tightened each time the vehicle is refueled. FLEXIBLE FUEL —...
STARTING AND OPERATING 361 ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materials lit in or near the vehicle when remov- ing the fuel filler tube cap (gas cap) or filling the tank.
362 STARTING AND OPERATING For best results, a refueling pattern that alternates be- Selection Of Engine Oil For Flexible Fuel Vehicles tween E-85 and unleaded gasoline should be avoided. (E-85) and Gasoline Vehicles When you do switch fuels, it is recommended that Whether operating the vehicle on an E-85 ethanol fuel or unleaded gasoline the engine oil requirements are the •...
STARTING AND OPERATING 363 Cruising Range Maintenance Because E-85 fuel contains less energy per gallon than If you operate the vehicle using E-85 fuel, follow Sched- gasoline, you will experience an increase in fuel con- ule B in the maintenance schedule section of this manual. sumption.
364 STARTING AND OPERATING Vehicle Certification Label Gross Vehicle Weight Rating (GVWR) Your vehicle has a certification label attached to the The GVWR is the total allowable weight of your vehicle. driver’s door pillar. This includes driver, passengers, and cargo. The total load must be limited so that you do not exceed the The label contains the following information: GVWR.
STARTING AND OPERATING 365 Tire Size Overloading The tire size on the Label represents the actual tire size on The load carrying components (axle, springs, tires, your vehicle. Replacement tires must be equal to the load wheels, etc.) of your vehicle will provide satisfactory capacity of this tire size.
366 STARTING AND OPERATING Loading CAUTION! To load your vehicle properly, first figure out its empty weight, axle by axle and side by side. Store heavier items Do not load your vehicle any heavier than the down low and be sure you distribute their weight as GVWR or the maximum front and rear GAWR.
STARTING AND OPERATING 367 A loaded vehicle is shown in the illustration. Note that Example Only Front Rear Axle neither the GVWR or the GAWR capacities have been Axle exceeded. Empty Weight 2,140 lbs 1,470 lbs (971 kg) (667 kg) Load (Including driver, pas- 360 lbs 980 lbs...
368 STARTING AND OPERATING To maintain warranty coverage, follow the requirements loaded and ready for operation condition. The recom- and recommendations in this manual concerning ve- mended way to measure GTW is to put your fully loaded hicles used for trailer towing. trailer on a vehicle scale.
Page 369
STARTING AND OPERATING 369 that typically provides adjustable friction associated with WARNING! the telescoping motion to dampen any unwanted trailer swaying motions while traveling. It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition Weight-Carrying Hitch can result if either rating is exceeded.
Page 370
370 STARTING AND OPERATING safety. The addition of a friction / hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability. Trailer sway control and a weight distributing (load equalizing) hitch are recommended for heavier Tongue Weights (TW) and may be required depending on Vehicle and Trailer configuration / loading to comply with gross axle weight rating (GAWR) requirements.
STARTING AND OPERATING 371 Trailer Hitch Classification Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional Trailer Tow Prep Package. See your dealer for package content. The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.
372 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Trailer Hitch Classification Ratings) Class III - Heavy Duty 5,000 lbs (2 268 kg) The following chart provides the maximum trailer Class IV - Extra 10,000 lbs (4 540 kg) weight ratings towable for your given drivetrain.
Page 373
STARTING AND OPERATING 373 Engine/Transmission GCWR (Gross Com- Frontal Area Max. GTW (Gross Max. Tongue Wt. bined Wt. Rating) Trailer Wt.) 3.3L & 3.8L Auto- 6,600 lbs (2993 kg) 40 SQ. FT. (3.72 Up to 2 persons & 180 lbs (82 kg) square meters) Luggage 1,800 lbs matic...
374 STARTING AND OPERATING Engine/Transmission GCWR (Gross Com- Frontal Area Max. GTW (Gross Max. Tongue Wt. bined Wt. Rating) Trailer Wt.) 3.3L & 3.8L Auto- 8,600 lbs (3900 kg) 40 SQ. FT. (3.72 Up to 2 persons & 380 lbs (172 kg) matic with trailer square meters) Luggage 3,800 lbs...
Page 375
STARTING AND OPERATING 375 which will cause loss of control of the vehicle and trailer. Consider the following items when computing the Failure to load trailers heavier in front is the cause of weight on the rear axle of the vehicle: many trailer accidents.
376 STARTING AND OPERATING Towing Requirements WARNING! To promote proper break-in of your new vehicle driv- etrain components the following guidelines are recom- Improper towing can lead to an injury accident. mended: Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer CAUTION!
Page 377
STARTING AND OPERATING 377 • When hauling cargo or towing a trailer, do not over- • Total weight must be distributed between the tow load your vehicle or trailer. Overloading can cause a vehicle and the trailer such that the following four loss of control, poor performance or damage to brakes, ratings are not exceeded: axle, engine, transmission, steering, suspension, chas-...
Page 378
378 STARTING AND OPERATING Tires–General Information section of this manual on Towing Requirements — Trailer Brakes Tire Pressures for proper tire inflation procedures. − Do not interconnect the hydraulic brake system or − Also, check the trailer tires for proper tire inflation vacuum system of your vehicle with that of the trailer.
Page 379
STARTING AND OPERATING 379 WARNING! CAUTION! Do not connect trailer brakes to your vehicle’s hy- If the trailer weighs more than 1,000 lbs (454 kg) draulic brake lines. It can overload your brake sys- loaded, it should have its own brakes and they tem and cause it to fail.
Page 380
380 STARTING AND OPERATING Towing Requirements — Trailer Lights & Wiring Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are required for motoring safety. The Trailer Tow Package may include a 4 and 7 pin wiring harness.
STARTING AND OPERATING 381 Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range should be selected. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve perfor- mance and extend transmission life by reducing exces- sive shifting and heat build up.
382 STARTING AND OPERATING Towing Tips — Electronic Speed Control (If − Air Conditioning Turn off temporarily. Equipped) − Don’t use in hilly terrain or with heavy loads. − refer to Cooling System Operating information in the Maintenance section of this manual for more informa- −...
384 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER flash on and off to warn oncoming traffic of an emer- The hazard flasher switch is located in the center of gency. Push the switch a second time to turn off the the instrument panel above the radio.
WHAT TO DO IN EMERGENCIES 385 IF YOUR ENGINE OVERHEATS CAUTION! In any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- Driving with a hot cooling system could damage tion. your vehicle. If temperature gauge reads “H”, pull over and stop the vehicle.
386 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! A hot engine cooling system is dangerous. You or WARNING! others could be badly burned by steam or boiling • Getting under a jacked-up vehicle is dangerous. coolant. You may want to call a service center if your The vehicle could slip off the jack and fall on vehicle overheats.
WHAT TO DO IN EMERGENCIES 387 Jacking Instructions — Stow ’n Go Seating WARNING! Preparations For Jacking Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off WARNING! the road to avoid the danger of being hit when operating the jack or changing the wheel.
Page 388
388 WHAT TO DO IN EMERGENCIES Jack Location — Stow ’n Go Seating Remove the scissors jack and jack handle by rotating the The jack, jack handle and winch handle tools are stowed small wing nut to the left. Also remove the tool pouch behind the rear left side trim panel in the rear cargo area.
Page 389
WHAT TO DO IN EMERGENCIES 389 Spare Tire Stowage — Stow ’n Go Seating For vehicles equipped with Stow ’n Go seating, the spare tire is stowed inside a protective cover located under the center of the vehicle by means of a cable winch mecha- nism.
Page 390
390 WHAT TO DO IN EMERGENCIES Jacking Instructions — Stow ’n Go Seating 1. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground. 2. To remove the compact spare tire/cover assembly, assemble the winch handle extensions to form a “T’...
Page 391
WHAT TO DO IN EMERGENCIES 391 NOTE: If either front tire is flat, it may be necessary to CAUTION! jack up the vehicle to remove the compact spare tire/ cover assembly from under the vehicle. Refer to jack The winch mechanism is designed for use with the engagement locations in the following steps for proper winch “T”...
Page 392
392 WHAT TO DO IN EMERGENCIES 4. When the compact spare tire/cover assembly is clear 5. There are two jack engagement locations on each side of the vehicle, stand the tire/cover assembly upright and of the body, refer to the following illustration. remove the wheel spacer by squeezing the two retaining tabs together.
Page 393
WHAT TO DO IN EMERGENCIES 393 Jack Engagement Locations...
Page 394
394 WHAT TO DO IN EMERGENCIES 6. These locations are on the sill flange of the body and WARNING! consist of a pair of downstanding tabs. The jack is to be located, engaging the flange, between the pair of tabs Raising the vehicle higher than necessary can make closest to the wheel to be changed.
Page 395
WHAT TO DO IN EMERGENCIES 395 10. Lower the vehicle by turning the jack screw to the 13. Place the deflated (flat) tire and compact spare tire left. cover assembly in the rear cargo area, have the tire repaired or replaced as soon as possible. 11.
Page 396
396 WHAT TO DO IN EMERGENCIES 15. Stow the jack, jack handle and winch handle tools. Secure The Spare Tire As Follows: 1. To stow the compact spare tire/cover assembly on vehicles equipped with Stow ’n Go seating, assemble the winch handle extensions to form a “T’...
Page 397
WHAT TO DO IN EMERGENCIES 397 WARNING! A loose compact spare tire/cover assembly, thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the com- pact spare tire with the cover assembly in the place provided.
Page 398
398 WHAT TO DO IN EMERGENCIES 2. Assemble the winch handle extensions to form the WARNING! Spare Tire Hook and pull the wheel spacer from under the vehicle. Verify that ’both’ retainer tabs of the wheel spacer have been properly extended through the center of 3.
WHAT TO DO IN EMERGENCIES 399 WARNING! CAUTION! Do not attempt to change a tire on the side of the For vehicles equipped with Stow ’n Go seating, the vehicle close to moving traffic. Pull far enough off Winch Mechanism is designed specifically to stow a the road to avoid the danger of being hit when COMPACT Spare Tire ONLY.
Page 400
400 WHAT TO DO IN EMERGENCIES Jack Location — Non Stow ’n Go Seating Spare Tire Stowage — Non Stow ’n Go Seating The jack, jack handle are stowed behind the rear left side For vehicles not equipped with Stow ’n Go seating the trim panel in the rear cargo area.
Page 401
WHAT TO DO IN EMERGENCIES 401 2. Fit the jack handle over the drive nut. Rotate the nut to the left until the spare is on the ground with enough slack cable to allow you to pull the tire out from under the vehicle.
Page 402
402 WHAT TO DO IN EMERGENCIES Jack Engagement Locations...
Page 403
WHAT TO DO IN EMERGENCIES 403 5. These locations are on the sill flange of the body and WARNING! consist of a pair of downstanding tabs. The jack is to be located, engaging the flange, between the pair of tabs Raising the vehicle higher than necessary can make closest to the wheel to be changed.
Page 404
404 WHAT TO DO IN EMERGENCIES NOTE: Do not install the wheel cover on the compact WARNING! spare. A loose tire or jack, thrown forward in a collision or Do not use a hammer or force to install the wheel covers. hard stop could endanger the occupants of the ve- 9.
WHAT TO DO IN EMERGENCIES 405 • For convenience in checking the spare tire inflation, JUMP-STARTING PROCEDURE stow with the valve stem toward the rear of the WARNING! vehicle. • Using the jack handle, rotate the drive nut to the •...
Page 406
406 WHAT TO DO IN EMERGENCIES Check the Battery Test Indicator (if equipped). If a light or 4. Connect one end of a jumper cable to the positive bright colored dot is visible in the indicator (if equipped), terminal of the discharged battery. Connect the other end DO NOT jump-start the battery.
WHAT TO DO IN EMERGENCIES 407 WARNING! WARNING! Do not connect the cable to the negative post of the Any procedure other than above could result in: discharge battery. The resulting electrical spark 1. Personal injury caused by electrolyte squirting could cause the battery to explode.
408 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE WARNING! With Ignition Key Fast spinning tires can be dangerous. Forces gener- Your vehicle may be towed under the following condi- ated by excessive wheel speeds may cause tire dam- tions: The gear selector must be in NEUTRAL, the age or failure.
WHAT TO DO IN EMERGENCIES 409 If it is necessary to use the accessories while being towed CAUTION! (wipers, defrosters, etc.), the key must be in the ON position, not the ACCESSORY position. Make certain the • Do not attempt to tow this vehicle from the front transmission remains in NEUTRAL.
410 WHAT TO DO IN EMERGENCIES TOWING THIS VEHICLE BEHIND ANOTHER TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE (Flat towing with all four wheels on the VEHICLE WITH A TOW DOLLY ground) The manufacturer does not recommend that you tow a Flat towing of vehicles equipped with an automatic front wheel drive vehicle on a tow dolly.
416 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors • Prolonged driving with the “Malfunction Indica- the performance of the emissions, engine, and automatic tor Light”...
MAINTAINING YOUR VEHICLE 417 cap until a clicking sound is heard. This is an indication is functioning and is not on when the engine is running, that the gas cap is properly tightened. Press the odometer and that the OBD (On Board Diagnostic) system is ready reset button to turn the message off.
418 MAINTAINING YOUR VEHICLE 4. As soon as you turn your key to the ON position, you you may need to do nothing more than drive your will see your MIL symbol come on as part of a normal vehicle as you normally would in order for your OBD bulb check.
MAINTAINING YOUR VEHICLE 419 DEALER SERVICE MAINTENANCE PROCEDURES Your dealer has the qualified service personnel, special The pages that follow contain the required maintenance tools, and equipment to perform all service operations in services determined by the engineers who designed your an expert manner.
420 MAINTAINING YOUR VEHICLE Engine Oil Checking Oil Level To assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop. The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off or before starting the engine after it has sat overnight.
Page 421
MAINTAINING YOUR VEHICLE 421 • If equipped for and operating with E-85 (ethanol) Change Engine Oil Road conditions and your kind of driving affects the fuel. interval at which your oil should be changed. Check the If ANY of these apply to you, then change your engine oil following list to see if any apply to you.
Page 422
422 MAINTAINING YOUR VEHICLE American Petroleum Institute (API) Engine Oil For information on engine oil filler cap location, refer to the Engine Compartment illustration in this section. Identification Symbol This symbol means that the oil has Lubricants which do not have both, the engine oil certi- been certified by the American fication mark and the correct SAE viscosity grade num- Petroleum Institute (API).
MAINTAINING YOUR VEHICLE 423 Synthetic Engine Oils governmental agency for advice on how and where used There are a number of engine oils being promoted as oil and oil filters can be safely discarded in your area. either synthetic or semi-synthetic. If you chose to use Engine Oil Filter such a product, use only those oils that are American The engine oil filter should be replaced at every engine...
424 MAINTAINING YOUR VEHICLE Belts should be inspected for evidence of cuts, cracks, or replaced if there is any malfunction due to a faulty spark glazing, and replaced if there is indication of damage plug, malfunctioning spark plugs can damage the cata- which could result in belt failure.
MAINTAINING YOUR VEHICLE 425 Under normal operating conditions, the catalytic con- WARNING! verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure The air cleaner can provide a measure of protection proper catalyst operation and prevent possible catalyst in the case of engine backfire.
Page 426
426 MAINTAINING YOUR VEHICLE NOTE: Intentional tampering with emissions control In unusual situations involving grossly malfunctioning systems can result in civil penalties being assessed engine operation, a scorching odor may indicate severe against you. and abnormal catalyst overheating. If this occurs, the vehicle should be stopped, the engine shut off and the vehicle allowed to cool.
MAINTAINING YOUR VEHICLE 427 • Do not idle the engine with any spark plug wires WARNING! disconnected or removed, such as when diagnostic • Battery fluid is a corrosive acid solution and can testing, or for prolonged periods during very rough idling or malfunctioning operating conditions.
428 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance CAUTION! For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer • It is essential when replacing the cables on the at the start of each warm season. This service should battery that the positive cable is attached to the include cleaning of the condenser fins and a system positive post and the negative cable is attached to...
Page 429
MAINTAINING YOUR VEHICLE 429 Refrigerant Recovery And Recycling WARNING! R-134a Air Conditioning Refrigerant is a hydrofluorocar- • Use only refrigerants and compressor lubricants bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product. How- approved by the manufacturer for your air condi- ever, the manufacturer recommends that air conditioning tioning system.
430 MAINTAINING YOUR VEHICLE the black arrow on the bottom of the filter frame with the WARNING! direction of airflow (away from the blower motor and towards the center of the car). Fluid level should be checked on a level surface and with the engine off to prevent injury from moving Refer to the “Maintenance Schedules”...
MAINTAINING YOUR VEHICLE 431 Continued operation could result in failure of the univer- Steering Shaft Seal The steering shaft seal, at the point where the shaft passes sal joint due to water and dirt contamination of the through the bulkhead, is lubricated when it is installed. If grease.
432 MAINTAINING YOUR VEHICLE The external lock cylinders should be lubricated twice a Avoid using the wiper blades to remove frost or ice from year, preferably in the fall and spring. Apply a small the windshield. Keep the blade rubber out of contact with amount of a high quality lubricant such as Mopar Lock petroleum products such as engine oil, gasoline, etc.
MAINTAINING YOUR VEHICLE 433 vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment.
434 MAINTAINING YOUR VEHICLE Cooling System applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front of the A/C condenser for any WARNING! accumulation of bugs, leaves, etc. If dirty, clean by gently •...
Page 435
MAINTAINING YOUR VEHICLE 435 Cooling System — Drain, Flush and Refill CAUTION! At the intervals shown on the Maintenance Schedules, the system should be drained, flushed and refilled. Mixing of coolants other than specified HOAT en- gine coolants, may result in engine damage and may If the solution is dirty or contains a considerable amount decrease corrosion protection.
Page 436
436 MAINTAINING YOUR VEHICLE Adding Engine Coolant The use of lower quality water will reduce the amount of Your vehicle has been built with an improved engine corrosion protection in the engine cooling system. coolant that allows extended maintenance intervals. This Please note that it is the owner’s responsibility to main- coolant can be used up to 5 Years or 100,000 miles before tain the proper level of protection against freezing ac-...
Page 437
MAINTAINING YOUR VEHICLE 437 Disposal of Used Engine Coolant WARNING! Used ethylene glycol based engine coolant is a regulated • The warning words “DO NOT OPEN HOT” on substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your the cooling system pressure cap are a safety pre- community.
Page 438
438 MAINTAINING YOUR VEHICLE The radiator normally remains completely full, so there is If an examination of your engine compartment shows no no need to remove the radiator cap unless checking for evidence of radiator or hose leaks, the vehicle may be coolant freeze point or replacing coolant.
MAINTAINING YOUR VEHICLE 439 • Make sure that the radiator and coolant recovery routing to be sure hoses do not come in contact with any bottle overflow hoses are not kinked or obstructed. heat source or moving component which may cause heat damage or mechanical wear.
Page 440
440 MAINTAINING YOUR VEHICLE Insure nylon tubing in these areas has not melted or WARNING! collapsed. Riding the brakes can lead to brake failure and Inspect all hose connections such as clamps and cou- possibly an accident. Driving with your foot resting plings to make sure they are secure and no leaks are or riding on the brake pedal can result in abnormally present.
MAINTAINING YOUR VEHICLE 441 replaced immediately! Eventual deterioration of the hose Overfilling of fluid is not recommended because it may can take place resulting in a possibility of a burst failure. cause leaking in the system. Add enough fluid to bring the level up to the require- WARNING! ments described on the brake fluid reservoir.
442 MAINTAINING YOUR VEHICLE Fuel System Hoses WARNING! Electronic Fuel Injection high pressure fuel systems are designed with hoses which have unique material charac- Overfilling the brake fluid reservoir can result in teristics to provide adequate sealing and resist attack by spilling brake fluid on hot engine parts and the deteriorated gasoline.
Page 443
MAINTAINING YOUR VEHICLE 443 The dipstick is located just behind the radiator, lower CAUTION! right side. Using a transmission fluid other than the manufac- Selection of Lubricant turers recommended fluid may cause deterioration It is important that the proper lubricant is used in the in transmission shift quality and/or torque converter transmission to assure optimum transmission perfor- shudder.
Page 444
444 MAINTAINING YOUR VEHICLE Procedure For Checking Fluid Level 5. Remove the dipstick and determine if the fluid is hot The fluid level in the automatic transmission should be or warm. Hot fluid is approximately 180°F (82°C), which checked whenever the vehicle is serviced. Operation with is the normal operating temperature after the vehicle has an improper fluid level will greatly reduce the life of the been driven at least 15 miles (24 km).
Page 445
MAINTAINING YOUR VEHICLE 445 Severe Usage is defined as: CAUTION! • Police, taxi, limousine, commercial type operation, or Do not overfill. Dirt and water in the transmission trailer towing where the vehicle is driven regularly for can cause serious damage. To prevent dirt and water more than 45 minutes of continuous operation.
446 MAINTAINING YOUR VEHICLE Front And Rear Wheel Bearings The following maintenance recommendations will enable Front and rear wheel bearings are permanently sealed. you to obtain maximum benefit from the corrosion No regular maintenance is required for these compo- resistance built into your vehicle. nents.
Page 447
MAINTAINING YOUR VEHICLE 447 Washing CAUTION! • Wash your vehicle regularly. Always wash your ve- Do not use abrasive or strong cleaning materials hicle in the shade using Mopar Car Wash or a mild car such as steel wool or scouring powder, which will wash soap, and rinse the panels completely with clear scratch metal and painted surfaces.
Page 448
448 MAINTAINING YOUR VEHICLE • If your vehicle is damaged due to an accident or heavy soil and/or excessive brake dust, use Mopar similar cause which destroys the paint and protective Wheel Cleaner (05066247AB) or equivalent or select a coating, have your vehicle repaired as soon as pos- nonabrasive, non-acidic cleaner.
Page 449
MAINTAINING YOUR VEHICLE 449 Your leather upholstery can be best preserved by regular Cleaning High Gloss Front Door B-pillar cleaning with a damp soft cloth. Small particles of dirt Appliques can act as an abrasive and damage the leather upholstery When cleaning the front door B-pillar appliques, care and should be removed promptly with a damp cloth.
450 MAINTAINING YOUR VEHICLE equipped with electric defrosters or the right rear quarter Seat Belt Maintenance window equipped with the radio antenna. Do not use Do not bleach, dye or clean the belts with chemical scrapers or other sharp instruments which may scratch solvents or abrasive cleaners.
Page 451
MAINTAINING YOUR VEHICLE 451 hour. After one hour pull the drawer from the water and dip it back into the water about six times. This will loosen any remaining debris. Rinse the drawer thoroughly un- der warm running water. Shake the excess water from the drawer and dry the outer surfaces with a clean soft cloth.
452 MAINTAINING YOUR VEHICLE FUSES — INTEGRATED POWER MODULE Cavity Cartridge Description An Integrated Power Module (IPM) located in the engine Fuse compartment near the battery. This center contains car- 30 Amp Front Wipers tridge fuses and mini fuses. A label that identifies each Pink component may be printed on the inside of the cover.
Page 453
MAINTAINING YOUR VEHICLE 453 Cavity Cartridge Description Cavity Mini Fuse Description Fuse 20 Amp Yel- 12 Volt Out Ignition or 40 Amp Power Windows Battery Green 20 Amp Yel- Horn 40 Amp Headlight Washers (Export Green Only) 20 Amp Yel- EWD/ Rear Wiper 40 Amp Power Sliding Door...
Page 454
454 MAINTAINING YOUR VEHICLE Cavity Mini Fuse Description CAUTION! 25 Amp Anti-Lock Brake System • When installing the Integrated Power Module Natural (ABS) Module cover, it is important to ensure the cover is prop- 10 Amp Red Ignition Switch erly positioned and fully latched. Failure to do so 20 Amp Yel- Hazard may allow water to get into the Integrated Power...
MAINTAINING YOUR VEHICLE 455 • Anytime you store your vehicle, or keep it out of The Heated Mirrors, Lower Instrument Panel Power Outlet and Removable Floor Console, when in the front service (i.e. vacation) for two weeks or more, run the position are fused with self resetting fuses that are only air conditioning system at idle for about five minutes serviceable by an authorized dealer.
456 MAINTAINING YOUR VEHICLE NOTE: For lighted switches, see your dealer for replace- BULB REPLACEMENT ment instructions. Headlights All of the interior bulbs are glass wedge base or glass 1. Remove the three screws securing the headlight mod- cartridge types. Aluminum base bulbs are not approved ule.
Page 457
MAINTAINING YOUR VEHICLE 457 2. Turn the bulb socket retaining ring or the bulb assem- NOTE: On some vehicles it may be necessary to slide bly counterclockwise. the red release lock rearward and push forward on the connector while depressing the release tab. CAUTION! Do not touch the new bulb with your fingers.
458 MAINTAINING YOUR VEHICLE Front Park/Turn Signal and Sidemarker Lights 1. Remove the three screws securing the headlight mod- ule. 3. Replace bulb, reinstall socket and then reinstall the headlight module. 2. Twist the turn signal socket to remove from the headlight module and pull bulb from socket.
MAINTAINING YOUR VEHICLE 459 Fog Lights Rear Tail, Stop, Turn Signal, Side Marker and Back-up Lights 1. Reach behind the front fascia from under the vehicle. 1. Raise the liftgate. 2. Twist the front fog light bulb to remove from the fog light housing.
460 MAINTAINING YOUR VEHICLE 3. Squeeze the socket assembly tabs to remove it from the Center High Mounted Stop Light (CHMSL) housing. 1. Remove the two screws securing the CHMSL. 4. Pull the bulb to remove it from the socket. 2.
MAINTAINING YOUR VEHICLE 461 4. Replace the bulb, reinstall the socket and reattach the 2. Pull the bulb out of the socket. Replace the bulb and CHMSL. reattach the lens assembly. License Light 1. Remove the two lens assembly mounting screws. FLUIDS AND CAPACITIES U.S.
Page 462
462 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) or equivalent 2.4 Liter Engine Oil Use API Certified SAE 5W-30 engine oil. Refer to your oil filler cap for cor- rect SAE grade, meeting DaimlerChrysler Material Standard MS-6395.
Page 463
MAINTAINING YOUR VEHICLE 463 Chassis Component Fluids, Lubricants and Genuine Parts. Automatic Transmission Mopar ATF+4 Automatic Transmission Fluid. Brake Master Cylinder Mopar DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids.
Page 465
MAINTENANCE SCHEDULES CONTENTS ▫ Schedule “B” ......469 Emission Control System Maintenance ..466 ▫...
466 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE MAINTENANCE SCHEDULES The “Scheduled” maintenance services, listed in bold There are two maintenance schedules that show the type must be done at the times or mileages specified to required service for your vehicle. assure the continued proper functioning of the emission First is Schedule “B”.
Page 467
MAINTENANCE SCHEDULES 467 • Taxi, police, or delivery service (commercial ser- CAUTION! vice). Failure to perform the required maintenance items • Off-road or desert operation. may result in damage to the vehicle. • If equipped for and operating with E-85 (ethanol) fuel.
Page 468
468 MAINTENANCE SCHEDULES Once a Month At Each Oil Change • Check tire pressure and look for unusual wear or • Change the engine oil filter. damage. • Inspect the exhaust system. • Inspect the battery and clean and tighten the terminals •...
SCHEDULE “B” 469 • Short trips of less than 16 km (10 miles). SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle • More than 50% of your driving is at sustained high under one or more of the following conditions. Change speeds during hot weather, above 32°...
Page 480
480 SCHEDULE “A” Miles 42, 000 48, 000 54, 000 60, 000 66, 000 72, 000 (Kilometers) (70 000) (80 000) (90 000) (100 000) (110 000) (120 000) [Months] [42] [48] [54] [60] [66] [72] Inspect the serpentine drive belt on 3.3 liter and 3.8 liter engines, replace if necessary.
Page 481
SCHEDULE “A” 481 Miles 78, 000 84, 000 90, 000 96, 000 (Kilometers) (130 000) (140 000) (150 000) (160 000) [Months] [78] [84] [90] [96] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. Replace the engine air cleaner filter.
Page 482
482 SCHEDULE “A” Miles 102, 000 108, 000 114, 000 120, 000 (Kilometers) (170 000) (180 000) (190 000) (200 000) [Months] [102] [108] [114] [120] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. Replace the engine air cleaner filter.
Page 483
SCHEDULE “A” 483 Miles 102, 000 108, 000 114, 000 120, 000 (Kilometers) (170 000) (180 000) (190 000) (200 000) [Months] [102] [108] [114] [120] Inspect the serpentine drive belt on 3.3 liter and 3.8 liter engines, replace if necessary. ‡ Flush and replace the engine coolant at 120 months, if not done at 102,000 miles.
Warranty service must be done by an authorized or work done that is not on your maintenance log, let the Chrysler, Dodge, or Jeep dealer. We strongly recommend service advisor know. that you take your vehicle to your selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
Page 487
IF YOU NEED CONSUMER ASSISTANCE 487 • Vehicle identification number technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely • Vehicle delivery date and mileage manner. DaimlerChrysler Motors Corporation Customer Center This is why you should always talk to your dealer’s P.O.
Page 488
488 IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech contract, call the manufacturer’s Service Contract Na- tional Customer Hotline at 1-800-521-9922. Impaired (TDD/TTY) To assist customers who have hearing difficulties, the The manufacturer will not stand behind any service manufacturer has installed special TDD (Telecommuni- contract that is not the manufacturer’s Service Contract.
IF YOU NEED CONSUMER ASSISTANCE 489 campaign. However, NHTSA cannot become involved in WARRANTY INFORMATION (U.S. Vehicles Only) See the Warranty Information Booklet for the terms and individual problems between you, your dealer, and the provisions of DaimlerChrysler’s warranties applicable to manufacturer.
490 IF YOU NEED CONSUMER ASSISTANCE Transport Canada, Motor Vehicle Defect Investigations need in diagnosing/troubleshooting, problem solving, and Recalls, 2780 Sheffield Road, Ottawa, Ontario K1B maintaining, servicing, and repairing DaimlerChrysler 3V9. Corporation vehicles. A complete working knowledge of the vehicle, system, and/or components is written PUBLICATION ORDER FORMS in straightforward language with illustrations, dia- To order the following manuals, you may use either the...
The following describes the tire grading categories estab- of service and engineering specialists to acquaint you lished by the National highway Traffic Safety Adminis- with specific Chrysler group vehicles. Included are tration. The specific grade rating assigned by the tire’s starting, operating, emergency and maintenance pro-...
492 IF YOU NEED CONSUMER ASSISTANCE may depart significantly from the norm due to variations Temperature Grades in driving habits, service practices and differences in road The temperature grades are A (the highest), B, and C, characteristics and climate. representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under Traction Grades controlled conditions on a specified indoor laboratory...
Page 493
IF YOU NEED CONSUMER ASSISTANCE 493 WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under inflation, or excessive load- ing, either separately or in combination, can cause heat buildup and possible tire failure.
Page 502
502 INDEX Fold in Floor (Stow n Go) Seating ... 129 Garage Door Opener (HomeLink ) ... 177 Freeing A Stuck Vehicle ....407 Gas Cap (Fuel Filler Cap) .
Page 503
INDEX 503 Head Phones ......268 Key ....... . . 12 Head Restraints .
Page 504
504 INDEX Jack Location ....388,390,400,401 Liftgate ....... . 40 Jack Operation .
Page 505
INDEX 505 Headlights On Reminder ....153 Service Engine Soon (Malfunction Indicator) . . . 218 High Beam Indicator ....217 Side Marker .
Page 512
512 INDEX Load Capacity ..... 332,333 Traction Control Switch ....158,324 Pressure Monitor System (TPMS) .
Page 513
INDEX 513 Transmitter Battery Service (Remote Vanity Mirrors ......99 Keyless Entry) ......26 Variance, Compass .
Page 514
514 INDEX Wheel and Wheel Trim ....448 Windshield Washers ....156,432 Wheel and Wheel Trim Care .
Page 515
INTRODUCTION Illuminated Vanity Mirrors - If Equipped INTRODUCTION HANDS-FREE COMMUNICATION (UConnect) - IF EQUIPPED HOW TO USE THIS MANUAL Operations WARNINGS AND CAUTIONS Phone Call Features VEHICLE IDENTIFICATION NUMBER UConnect System Features VEHICLE MODIFICATIONS/ALTERATIONS Advanced Phone Connectivity THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Things You Should Know About Your UConnect System A WORD ABOUT YOUR KEYS General Information...
Page 516
Front Seat Storage Bin - If Equipped Operating Instructions - CD/DVD Changer Second Row Seat Storage bins - If Equipped EJECT (EJT) Button Overhead Rail System - If Equipped Remote Control Operating Instructions Removable Floor Console With Stow n Go Seating - If Equipped Operating Instructions - Video Screen Removable Floor Console Without Stow n Go Seating - If Equipped Operating Instructions - Headphones...
Page 517
Tire Pressure Monitoring Low Pressure Warnings Windshield and Rear Window Washers Base Tire Pressure Monitoring System with Electronic Vehicle Information Center (EVIC) - If Equipped Exhaust System Service Tire System Soon Cooling System Using Your Compact Spare - Basic Tire Pressure Monitoring System Only Hoses And Vacuum/Vapor Harnesses General Information Brakes...
Need help?
Do you have a question about the Dodge Caravan 2007 and is the answer not in the manual?
Questions and answers