Chrysler RAM TRUCK 2500 1994 Service Manual page 840

SPECIFICATIONS—S.OL ENGINE
ENGINE SPECIFICATIONS
Camshaft
Bore Diameter
No.l 5 3 . 1 6 - 53.19 mm
(2.093 - 2.094 in)
No.2 52.76 - 52.78 mm
(2.077 - 2.078 in)
No.3 52.35 - 52.37 mm
(2.061 - 2.062 in)
No.4 5 1 . 9 4 - 5 1 . 9 7 mm
(2.045 - 2.046 in)
No.5 51.54 - 51.56 mm
(2.029 - 2.030 in)
No.6 ..48.74 - 48.77 mm
( 1 . 9 1 9 - 1 . 9 2 0 in)
Diametrical Clearance
No.l & No.3 - No.6 0.0254 - 0.0762 mm
(0.001 - 0.003 in)
No.2 0.0381 - 0.0889 mm
(0.0015 - 0.0035 in)
End Play 0.127-0.381 mm
( 0 . 0 0 5 - 0 . 0 1 5 in)
Bearing Journal Diameter
No.l 53.11 - 5 3 . 1 4 mm
(2.091 - 2.092 in)
No.2 52.69 - 52.72 mm
(2.0745 - 2.0755 in)
No.3 52.30 - 52.32 mm
(2.059 - 2.060 in)
No.4 51.89 - 51.92 mm
(2.043 - 2.044 in)
No.5 51.49-51.51 mm
(2.027 - 2 . 0 2 8 in)
No.6 .48.69 - 48.72 mm
(1.917- 1.918 in)
Connecting Rods
Bearing Clearance 0.005 - 0.074 mm
(0.0002 - 0.0029 in)
Piston Pin Bore Diameter 24.940 - 24.978 mm
(0.9819 - 0.9834 in)
Side Clearance (Two Rods) 0.25 - 0.46 mm
(0.010-0.018 in)
Total Weight (Less Bearing) 744 grams
(26.24 oz)
Crankshaft
Connecting Rod Journal
Diameter 53.950 - 53.975 mm
( 2 . 1 2 4 - 2 . 1 2 5 in)
Out-of-Round (Max.) 0.0254 mm
(0.001 in)
Taper (Max.) 0.0254 mm
(0.001 in)
Crankshaft (Cant.)
Main Bearing Diametrical Clearance
No.l - No.6 ...0.0)51 - 0 . 0 5 8 mm
(0.0002 - 0.0023 in)
Max. Allowable ...0.071 mm
(0.0028 in)
End Play 0.051 - 0 . 4 3 2 mm
( 0 . 0 ) 2 - 0 . 0 1 7 in)
Max. Allowable ....0.559 mm
(0.022 in)
Main Bearing Journals
Diameter 76.187 - 76.213 mm
(2.9995 - 3.0005 in)
Out-of-Round (Max.) 0.0254 mm
(0.0)1 in)
Taper (Max.) ...0.0254 mm
(0.001 in)
Cylinder Block
Cylinder Bore
Diameter ...101.60- 101.61 mm
(4.0000 - 4 . 0 0 ) 5 in)
Out-of-Round (Max.) 0.127 mm
(0.0)5 in)
Taper (Max.) 0.254 mm
(0.010 in)
Tappet Bore Diameter 22.982 - 23.010 mm
(0.9048 - 0.9059 in)
Cylinder Head
Compression Pressure 1172 - 1310 kPa
( 1 7 0 - 1 9 0 psi)
Gasket Thickness (Compressed) 0.991 - 1.118 mm
(0.039 - 0.044 in)
Valve Seat
Angle 44.5°
Runout (Max.) 0.076 mm
(0.003 in)
Width (Finish)
Intake & Exhaust ....1.02 - 1.52 mm
(0.040 - 0.060 in)
Guide Bore Diameter (Std.) 7.95 - 7.98 mm
( 0 . 3 1 3 - 0 . 3 1 4 in)
Hydraulic Tappets
Body Diameter 22.949 - 22.962 mm
(0.9035 - 0.9040 in)
Clearance in Block (Diametrial) 0.2030 - 0.0610 mm
(0.0008 - 0.0)24 in)
Plunger Travel Minimum (Dry) 4.24 mm
(0.167 in)
Push Rod Length 195.52 - 196.02 mm
( 7 . 6 9 8 - 7 . 7 1 7 in)
J9409-121