Danfoss VLT AutomationDrive FC 300 Design Manual page 274

FC 300 Design Guide
..............................................
Pre-magnetizing
.........................................................
Preheat
..............................................
Preset Reference
Preset Reference Select
...........................................
Process PID Control
.......................................................
Profibus
Profibus Warning Word
............................................
PROFIdrive Profile
Programming of Torque Limit and Stop
..............................................
ProportionalGain
.........................................
Protection
Protection and Features
.......................................................
Protocols
...............................................
Pulse Reference
..........................................
Pulse/encoder inputs
Q
.......................................
Quick Menu
.......................................
Quick Menu mode
........................................
Quick Menu Password
Quick Stop Ramp Time
.............................................
Quick Stop Select
Quick Transfer of Parameter Settings
R
Ramp 1 Ramp-down Time
Ramp 1 Ramp-up Time
...................................................
Ramp 1 Type
Ramp 2 Ramp-down Time
Ramp 3 Ramp-down Time
Ramp 3 Ramp-up Time
Ramp 4 Ramp-down Time
....................................................
Ramp Delay
.....................................................
Ramp Time
..............................................
Rated motor speed
..........................................................
RCD
Read Parameter Description Elements
............................................
Reference Handling
........................................
Reference Resource 1
.............................................
Regional Settings
Relative Scaling Reference Resource
..............................................
Relay connection
.............................................
Relay outputs
......................................................
Reset
Reset Control Word Timeout
...........................................
Reset kWh Counter
....................................................
Reset Mode
............................................
Reset] Key on LCP
274
......................................
.......................................
...................
18, 51, 52, 91
......................................
120, 123, 126
.......................................
.....................
...................................
......................................
...................................
...................................
......................................
...................................
....................
......................
................................
MG.33.B3.22 - VLT is a registered Danfoss trademark
Index
148 Residual Current Device
........................................................
151 Rise time
155 Rotor Leakage Reactance (X2)
185 Rotor Resistance (Rr)
37
6, 70
S
188
248
shielded/armored
42
Step-by-Step
179
....................................................
Safe Stop
Safe Stop Installation
56
Safety Grounding
235
Scaling of References and Feedback
216
Serial communication
58
Side-by-side installation
Smart Logic Controller
Software versions
Speed control, closed loop
Speed control, open loop
123, 126 Speed PID
139 Speed PID Control
161 Speed PID Lowpass Filter Time
184 Start Delay
121 Start Function
Start Speed [Hz]
Start Speed [RPM]
Stator leakage reactance
Stator Leakage Reactance (X1)
157
Stator Resistance (Rs)
156
...........................................................
Status
156
Status messages
158
Status Word
159
.......................................................
Step Size
159
Surroundings
160
Switches S201, S202, and S801
162
Switching Frequency
161
9
11, 52
T
255
25 Telegram Structure
155 Telegram Traffic
132 Temperature-Dependent Switch Frequency
156 Term 32/33 Encoder Direction
102 Term 32/33 Gear Denominator
59, 169 Term 32/33 Gear Numerator
121, 124 Term. 29 Low Frequency
183 Terminal 10
209 Terminal 37
206 Terminal 53 High Current
138 Terminal 53 Low Current
......................................
.............................
........................................
..............................................
..................................................
.........................................
.............................................
........................
......................................
..................................
..............................................
..................................
....................................
...................................................
............................................
.............................
...............................................
...........................................
..............................................
............................................
....................................
............................
.......................................
..............................................
.............................................
...................................................
............................
.........................................
...........................................
...............................................
..............................
.............................
................................
....................................
.....................................................
.....................................................
....................................
....................................
52
61
143
142
96
130
17, 54
99
106
........................
26
10, 60, 109, 253
86
50, 195
70
140
140
19, 20
33
179
147, 147
147, 147
148
148
142
143
142
120
119
246, 251
161
60
96
205
235
235
...............
63
174
174
174
171
94
54
175
175