Danfoss VLT AutomationDrive FC 300 Design Manual page 168

FC 300 Design Guide
400 msec. the resulting reference will ramp
you according to Ramp 2 (par. 3-41).
Unchanged speed
Reduced by %-value
Increased by %-value
Reduced by %-value
• Slow-down [29]: Same as Catch up [28].
Pulse input [32]: Select Pulse input if you
•
use a pulse sequence as either reference or
feedback. Scaling is done in par. group 5-5*.
• Ramp bit 0 [34]
Ramp bit 1 [35]
•
Mains failure inverse
•
activate par. 14-10 Mains Failure. Mains failure
inverse is active in the Logic '0' situation.
DigiPot increase
•
INCREASE signal to the Digital Potentiometer
function described in parameter group 3-9*
• DigiPot decrease
DECREASE signal to the Digital Potentiometer
function described in parameter group 3-9*
DigiPot clear [57]: Uses the input to
•
CLEAR the Digital Potentiometer reference
described in parameter group 3-9*
Counter A (up) [60]: (Terminal 29 only) Input
•
for increment counting in the SLC counter.
• Counter A (down)
Input for decrement counting in the SLC counter.
Reset Counter A
•
reset of counter A.
• Counter B (up) [63]: (Terminal 29 only) Input
for increment counting in the SLC counter.
Counter B (down)
•
Input for decrement counting in the SLC counter.
• Reset Counter B
reset of counter B.
• Slow [22]: Same as Speed up [21].
Set-up select bit 0 [23]
•
Set-up, bit 0 and bit 1 provides the ability to
choose between one of the four set-ups. You
must set par. 0-10 to Multi setup.
Set-up select bit 1 [24]
•
32): Same as Set-up select bit 0 [23].
default setting ( ) display text
*
168
How to Program
Slow-down Catch up
0 0
1 0
0 1
1 1
[36]: Is selected to
[55]: Uses the input as an
[56]: Uses the input as a
[61]: (Terminal 29 only)
[62]: Input for
[64]: (Terminal 29 only)
[65]: Input for
: Selection of
(Default Digital input
[ ] value for use in communication via serial communication port
MG.33.B3.22 - VLT is a registered Danfoss trademark
Catch up [28]: Select Catch up/Slow-down
•
to increase or reduce the reference value
(set in par. 3-12).
5-10 Terminal 18 Digital Input
*
Start
Function:
5-11 Terminal 19 Digital Input
*
Reverse
5-12 Terminal 27 Digital Input
*
Coast inverse
5-13 Terminal 29 Digital Input
*
Jog
5-14 Terminal 32 Digital Input
*
No operation
5-15 Terminal 33 Digital Input
*
No operation
5-3* Digital Outputs
"
The 2 solid-state digital outputs are common
for terminals 27 and 29. Set the I/O function
for terminal 27 in par. 5-01, and set the I/O
function for terminal 29 in par. 5-02.
These parameters cannot be set while running.
No operation
Control ready
Drive ready
Drive ready / remote
Enable / no warning
VLT running
Running / no warning
Run in rnge, no warn
Run on ref., no warn.
Alarm
Alarm or warning
At torque limit
Out of current range
Below current, low
Above current, high
Out of speed range
Below speed, low
Above speed, high
Thermal warning
Ready, no thrm warn
Rmte rdy, no th wrn
[8]
[10]
[2]
[14]
[0]
[0]
[0]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
[13]
[14]
[15]
[16]
[17]
[21]
[22]
[23]