Xerox 3050 Service Manual page 607

Code
-
021 1
-
0261
7
0262
-
0263
Description
.anguage ROM Test
0
=
Both Language ROMs
are defective.
1 = Primary Language
ROM i s
good.
2
=
Secondary Language
ROM is good.
3
=
Both Language ROMs
are good.
Iountry Configuration
O= 115V
1
=
240 V (Refer t o Note
1)
2 = 220v
Jledia Width
'his code i s used t o control
vhat media width can be
rsed i n the copier.
1
=
inch
2 = metric (mm)
3
=
both
billing Meter Count
'his code i s used t o select the
billing i n meters or inches.
0
= inch
1
=
metric (decimeter)
Value
-
-
-
US0
1
RX
2
-
US0
0
RX
1
-
Note 1 : WIO TaglMOD 6: 50 Hz copiers
requiring 24OVAC: DO NOTset the code
102611
to 240 VAC. Set the code
102611
to
220 VAC. When the code 102611 i s set to 240
VAC,
a fusing temperature run away may
I
occur
in
normal copy mode or when
using
the codes
11004J andf09211.
WI TaglMOD
6: 50 Hz
copiers requiring
240VAC:
The code
[02611
may be set to 240
VAC.
-
Code
-
0360
-
0361
-
0362
-
0363
-
0364
-
0370
-
037 1
-
Description
NVM reset t o default.
Entering the number 1 or 3
resets all the NVM values t o
the default values.
Entering the number
2
allows the electronic billing to
be reset t o any desired value.
1
=
US0 NVM Default
2
=
Billing
3
=
EO NVM Defaults
Watchdog timer test.
Thi s
code can be use t o exit
the dia~nostics mode.
Diagnostic timeout interval.
This code allows the
adjustment of the time
interval that the copier will
stay in the diagnostic mode.
The time interval range is 5 t o
50 minutes.
- -
-
-
NVM Reset
This code allows the NVM
values t o be reset back t o the
previously adjusted values.
The software compares the
NVM values t o a backup file
and will reset the values that
are not the same as the values
in the backup file.
NVM Check sum.
Auditron NVM Reset t o
nominal.
This code allows the Technical
Representative t o change the
administrator number
without resetinrr NVM.
-
Value
-
-
-
5
min.
-
-
-
-
-
-
Code
-
0373
-
0374
-
0379
-
0561
7
0562
Description
Auditron NVM Reset t o
nominal.
This code allows the NVM
values t o be reset t o the
recorded Auditron values.
The software compares the
NVM values t o a backup file
and will reset the values that
are not the same as the values
in the backup file.
4uditron NVM Reset of
checksum.
4uditronl EFA (External
Foreign Accessory) Enable
0
= Auditronl EFA Off
1
=
Auditron On
2
=
External Foreign
Accessory On, billing
in square feet
3
=
External Foreign
Accessary On, billing
once per copy
[WI Tagl
MOD
2): This code
adjusts how far the document
travels on the scan cycle
before it starts the rescan.
Refer t o ADJ 5.2 Document
Etop Position
[WI Tagl
MOD
2): This code
adjusts how far the document
travels on the rescan cycle
before
it
gets scanned again
or stops at the end of the copy
cycle..
Refer t o ADJ 5.2 Document
Stor, Position
31 93
3050
6-5
Diagnostics