Radwin WinLink 1000 User Manual page 328

Trap Parameters
Table D-3: MIB Traps (Sheet 3 of 5)
Name
swVersionsMismatchFullCompatibilityAlarm
swVersionsMismatchRestrictedCompatibilityAlarm
swVersionsMismatchSoftwareUpgradeRequired
swVersionsIncompatible
hssMultipleSourcesDetectedAlarm
hssSyncToProperSourceStoppedAlarm
hssSyncPulseDetectedAlarm
tdmBackupAlarm
linkLockUnauthorizedRemoteODU
linkLockUnauthorizedODU
hotStandbyAlarm
sfpInsertion
sfpPort1DisconnectedAlarm
desiredRatioCanNotBeAppliedAlarm
cbwMismatch
gpsNotSynchronized
pdTooHighDueCbwLimitations
tdmServiceClear
ethServiceOpened
encryptionClear
changeLinkPasswordClear
WinLink 1000 User Manual
ID Severity Description
114 warning The trap is sent if SW versions mismatch with full link functionality.
Contains a single parameter which is its description: 1 - Description:
Software versions mismatch - full link functionality
115 minor The trap is sent if SW versions mismatch with restricted link functionality.
Contains a single parameter which is its description: 1 - Description:
Software versions mismatch - restricted link functionality
116 major The trap is sent if SW versions mismatch and SW upgrade is required.
Contains a single parameter which is its description: 1 - Description:
Software versions mismatch - Software upgrade required
117 critical The trap is sent if SW versions are incompatible. Contains a single
parameter which is its description: 1 - Description: SW Versions
incompatible
118 major Indicates that multiple sync pulse sources were detected. Contains a
single parameter which is its description: 1 - Description: HSS multiple
sync sources were detected.
119 major Indicates that synchronization to a proper sync pulse source was
stopped. Contains a single parameter which is its description: 1 -
Description: HSS sync pulse - Down. The reason is: %s. %s - Is the
reason for the sync down.
120 major Indicates that HSS additional sync pulse was detected. Contains a
single parameter which is its description: 1 - Description: HSS additional
sync pulse was detected.
121 major Indicates that the TDM backup link was activated. Contains a single
parameter which is its description: 1 - Description: TDM backup alarm -
backup link was activated.
122 major Indicates that the remote ODU is unauthorized.
parameter which is its description: 1 - Description: Unauthorized remote
ODU connection rejected.
123 major Indicates that the ODU is unauthorized.
which is its description: 1 - Description: Unauthorized ODU connection
rejected.
124 major Indicates that the hot standby secondary link was activated. Contains a
single parameter which is its description: 1 - Description: Secondary
Link Is Active.
126 normal Indicates that a device was inserted to SFP Port
127 major Indicates the SFP port 1 status changed to disconnected.Contains a
single parameter which is its description: 1 - Description: SFP port 1
status changed to disconnected.
129 normal Indicates Desired UL/DL RAtio Can Not Be Applied.
130 major Indicates that a Channel Bandwidth mismatch was detected.Contains two
parameters: 1 - Description: Channel Bandwidth Mismatch: one side is
%n0 MHz and the other is %n1 MHz. %n0 is the local Channel
Bandwidth value in MHz. %n1 is the remoet Channel Bandwidth value in
MHz.
131 major Indicates that the GPS is not synchronized with satellites. Pulses are
self generated.
132 major Indicates that link cannot be established because link range is too large
for channel bandwidth.
200 major Indicates that TDM Service fault is cleared. Contains a single parameter
which is its description: 1 - Description: TDM Service - Normal.
201 normal Indicates that Ethernet Service has been opened. Contains a single
parameter which is its description: 1 - Description: Ethernet Service has
been opened.
203 normal Indicates that encryption is OK. Contains a single parameter which is its
description: 1 - Description: Encryption Status - Normal.
204 normal Indicates that the Link Password was changed successfully. Contains a
single parameter which is its description: 1 - Description: Link Password
has been changed at/on: %s. %s - Is the Local Site name or Remote
Site name or both sides of the Link.
Release 1.9.40
Appendix D
Contains a single
Contains a single parameter
D-26