Table D-2 Private Mib P - Radwin WinLink 1000 User Manual

MIB Parameters
MIB Parameters
Table D-2: Private MIB Parameters (Sheet 1 of 18)
Name
winlink1000OduAdmProductType
winlink1000OduAdmHwRev
winlink1000OduAdmSwRev
winlink1000OduAdmLinkName
winlink1000OduAdmResetCmd
winlink1000OduAdmAddres
winlink1000OduAdmMask
winlink1000OduAdmGateway
winlink1000OduAdmBroadcast
winlink1000OduAdmHostsTable
winlink1000OduAdmHostsEntry
winlink1000OduAdmHostsIndex
winlink1000OduAdmHostsIp
winlink1000OduAdmHostsPort
winlink1000OduBuzzerAdminState
winlink1000OduProductId
winlink1000OduReadCommunity
winlink1000OduReadWriteCommunity
winlink1000OduTrapCommunity
WinLink 1000 User Manual
OID
1.3.6.1.4.1.4458.1000.1.1.1
1.3.6.1.4.1.4458.1000.1.1.2
1.3.6.1.4.1.4458.1000.1.1.3
1.3.6.1.4.1.4458.1000.1.1.4
1.3.6.1.4.1.4458.1000.1.1.5
1.3.6.1.4.1.4458.1000.1.1.6
1.3.6.1.4.1.4458.1000.1.1.7
1.3.6.1.4.1.4458.1000.1.1.8
1.3.6.1.4.1.4458.1000.1.1.10
1.3.6.1.4.1.4458.1000.1.1.12.1.2
1.3.6.1.4.1.4458.1000.1.1.12.1.3
1.3.6.1.4.1.4458.1000.1.1.13
1.3.6.1.4.1.4458.1000.1.1.14
1.3.6.1.4.1.4458.1000.1.1.15
1.3.6.1.4.1.4458.1000.1.1.16
1.3.6.1.4.1.4458.1000.1.1.17
Release 1.9.40
Type Description
DisplayString RO ODU configuration description.
DisplayString RO ODU Hardware Version.
DisplayString RO ODU Software Version.
DisplayString RW Link Name. A change is effective immediately.
Integer RW Reset Command. A set command with a value of 3
will cause a device reset. The read value is
always 0.
IpAddress RW ODU IP address. A change is effective after reset.
The parameter is kept for backward compatibility.
Using the alternative parameter:
winlink1000OduAdmIpParamsCnfg is
recommended.
IpAddress RW ODU Subnet Mask. A change is effective after
reset.
compatibility.
winlink1000OduAdmIpParamsCnfg is
recommended.
IpAddress RW ODU default gateway. A change is effective after
reset.
compatibility.
winlink1000OduAdmIpParamsCnfg is
recommended.
Integer RW This parameter is reserved for the Manager
application provided with the product.
N/A Trap destinations table. Each trap destination is
defined by an IP address and a UDP port. Up to
10 addresses can be configured.
N/A Trap destinations table entry. INDEX {
winlink1000OduAdmHostsIndex }
RO Trap destinations table index.
IpAddress RW Trap destination IP address. A change is effective
immediately.
Integer RW UDP port of the trap destination. A change is
effective immediately.
Integer RW This parameter controls the activation of the
buzzer while the unit is in install mode. A change
is effective immediately. The valid values are:
disabled (0) enabledAuto (1)
enabledConstantly(2).
DisplayString RO This parameter is reserved for the Manager
application provided with the product.
DisplayString RW Read Community String. This parameter always
returns ***** when retrieving its value. It is used
by the Manager application to change the Read
Community String. The SNMP agent accepts only
encrypted values.
DisplayString RW Read/Write Community String. This parameter
always returns ***** when retrieving its value. It is
used by the Manager application to change the
Read/Write Community String. The SNMP agent
accepts only encrypted values.
DisplayString RW Trap Community String. This parameter is used by
the Manager application to change the Trap
Community String. The SNMP agent accepts only
encrypted values.
Appendix D
The parameter is kept for backward
Using the alternative parameter:
The parameter is kept for backward
Using the alternative parameter:
D-6