B.3.4 System Configuration Commands - Comtech EF Data SNM-1001L Installation And Operation Manual

SNM-1001L Satellite Modem
Remote Control Operation
ASYNC Command:
Transmit Response:
Overhead Status:
Baud Rate Response:
Transmit Command:
Data Phase Response:
Status:
Response:
Receive Command:
Data Phase Response:
Status:
Response:
CTS Delay Command:
Time Response:
Status:
Response:

B.3.4 System Configuration Commands

Time Of Command:
Day Response:
Status:
Response:
Date Command:
Response:
Status:
Response:
Remote Command:
Response:
Clear Command:
Stored Response:
Faults
Modem Command:
Operation Response:
Mode Status:
Response:
System Command:
Modem Response:
Type Status:
Response:
Save Command:
Modem Response:
Config.
Recall Command:
Modem Response:
Config.
<add/TOBR_nnnnn'cr'
>add/TOBR_nnnnn'cr''lf']
<add/TOBR_'cr'
>add/TOBR_nnnnn'cr''lf']
<add/TDP_xxxx'cr'
>add/TDP_xxxx'cr''lf']
<add/TDP_'cr'
>add/TDP_xxxx'cr''lf']
<add/RDP_xxxx'cr'
>add/RDP_xxxx'cr''lf']
<add/RDP_'cr'
>add/RDP_xxxx'cr''lf']
<add/CTSD_xx'cr'
>add/CTSD_xx'cr''lf']
<add/CTSD_'cr'
>add/CTSD_xx'cr''lf']
<add/TIME_hh:mmxx'cr'
>add/TIME_hh:mmxx'cr''lf']
<add/TIME_'cr'
>add/TIME_hh:mmxx'cr''lf']
<add/DATE_mm/dd/yyyy'cr'
>add/DATE_mm/dd/yyyy'cr''lf']
<add/DATE_'cr'
>add/DATE_mm/dd/yyyy'cr''lf']
<add/REM_'cr'
>add/REM_'cr''lf']
<add/CLSF_'cr'
>add/CLSF_'cr''lf']
<add/MOM_xxxxxxx'cr'
>add/MOM_xxxxxxx'cr''lf']
<add/MOM_'cr'
>add/MOM_xxxxxxx'cr''lf']
<add/SMT_xxxxxxx'cr'
>add/SMT_xxxxxxx'cr''lf']
<add/SMT_'cr'
>add/SMT_xxxxxxx'cr''lf']
<add/SMC_n'cr'
>add/SMC_n'cr''lf']
<add/RMC_n'cr'
>add/RMC_n'cr''lf']
Where: nnnnn = 110, 150, 300, 600, 1200, 2400,
4800, 9600, 19200, or 38400.
Note: TX ASYNC Overhead only.
Where: xxxx = NRM (normal data phasing), INV
(inverted data phasing).
Where: xxxx = NRM (normal data phasing), INV
(inverted data phasing).
Where: xx = 0 to 60 (number of seconds).
Where:
hh = 1 to 12 (hours).
mm = 00 to 59 (minutes).
xx = AM or PM.
Where:
mm = 1 to 12 (month).
dd = 1 to 31 (day).
yyyy = 00 to 99 (year) in 2 - digit year mode, and 1975
to 1999 and 2000 to 2075 in 4 - digit mode.
Configures the modem for remote operation.
The SDM300L will respond to any status request at any
time. However, the SDM300L must be in 'Remote Mode'
to change configuration parameters.
This command is used to clear all stored faults logged by
the SDM300L.
Where: xxxxxxx = TX_ONLY, RX_ONLY, or DUPLEX.
This command configures the modem for simplex or
duplex operation modes. When transmit only mode is
selected, receive faults are inhibited and when receive
only mode is selected, transmit faults are inhibited.
Where: xxxxxx = AUPC, EFD, or CUSTOM.
Where: n = 1, 2, 3, 4, or 5 (stored configuration number).
This command saves the current modem configuration for
recall at a later time using the 'RMC_' command. Up to
five different modem configurations can be saved.
Where: n = 1, 2, 3, 4, or 5 (stored configuration number).
This command causes the modem to be reprogrammed
with configuration parameters previously saved using the
'SMC_' command. One of five saved configurations can
be specified.
B–11
Revision 1
MN/SNM1001L.IOM