Huawei NetEngine80E Configuration Manual - Reliability page 1423
Hide thumbs
Also See for NetEngine80E:
- Configuration manual (1301 pages) ,
- Configuration manual - reliability (761 pages) ,
- Installation manual (169 pages)
Table of Contents
Advertisement
HUAWEI NetEngine80E/40E Router
Configuration Guide - Reliability
# Configure user information (user group, IP address pool, user domain, and AAA domain) and
bind the user group to the NAT instance on CGN1.
[CGN1] user-group natbras
[CGN1] ip pool natbras bas local
[CGN1-ip-pool-natbras] gateway 193.32.0.1 255.255.0.0
[CGN1-ip-pool-natbras] section 0 193.32.0.2 193.32.0.254
[CGN1-ip-pool-natbras] quit
[CGN1] aaa
[CGN1-aaa] domain natbras
[CGN1-aaa-domain-natbras] authentication-scheme default0
[CGN1-aaa-domain-natbras] accounting-scheme default0
[CGN1-aaa-domain-natbras] ip-pool natbras
[CGN1-aaa-domain-natbras] user-group natbras bind nat instance nat1
[CGN1-aaa-domain-natbras] quit
[CGN1-aaa] quit
# Configure user information (user group, IP address pool, user domain, and AAA domain) and
bind the user group to the NAT instance on CGN2.
[CGN2] user-group natbras
[CGN2] ip pool natbras bas local
[CGN2-ip-pool-natbras] gateway 193.32.0.1 255.255.0.0
[CGN2-ip-pool-natbras] section 0 193.32.0.2 193.32.0.254
[CGN2-ip-pool-natbras] quit
[CGN2] aaa
[CGN2-aaa] domain natbras
[CGN2-aaa-domain-natbras] authentication-scheme default0
[CGN2-aaa-domain-natbras] accounting-scheme default0
[CGN2-aaa-domain-natbras] ip-pool natbras
[CGN2-aaa-domain-natbras] user-group natbras bind nat instance nat1
[CGN2-aaa-domain-natbras] quit
[CGN2-aaa] quit
Step 7 Configure an RBS on the CGN device.
# Configure an RBS on CGN1 and bind it to the NAT instance.
[CGN1] remote-backup-service natbras
[CGN1-rm-backup-srv-natbras] peer 1.1.1.2 source 1.1.1.1 port 7000
[CGN1-rm-backup-srv-natbras] ip-pool natbras
[CGN1-rm-backup-srv-natbras] nat-instance nat1
[CGN1-rm-backup-srv-natbras] quit
# Configure an RBS on CGN2 and bind it to the NAT instance.
[CGN2] remote-backup-service natbras
[CGN2-rm-backup-srv-natbras] peer 1.1.1.1 source 1.1.1.2 port 7000
[CGN2-rm-backup-srv-natbras] ip-pool natbras
[CGN2-rm-backup-srv-natbras] nat-instance nat1
[CGN2-rm-backup-srv-natbras] quit
Step 8 Configure a user-side unicast VRRP backup group for the CGN and the switch on the CGN
device.
# Configure a user-side unicast VRRP backup group for CGN1 and the switch.
[CGN1] interface LoopBack1
[CGN1-LoopBack1] ip address 8.1.1.1 255.255.255.0
[CGN1-LoopBack1] vrrp vrid 1 peer-ip 8.8.8.1
[CGN1-LoopBack1] vrrp vrid 1 priority 150
[CGN1-LoopBack1] vrrp vrid 1 preempt-mode timer delay 120
[CGN1-LoopBack1] vrrp vrid 1 track interface GigabitEthernet3/0/0 reduced 60
[CGN1-LoopBack1] vrrp vrid 1 track interface GigabitEthernet2/0/1.10 reduced 60
[CGN1-LoopBack1] vrrp vrid 1 track service-location 1 reduced 60
[CGN1-LoopBack1] quit
Issue 02 (2014-09-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
12 CGN Backing Up HA Configuration
1406
Advertisement
Table of Contents
