Specifications - Mitsubishi Q00JCPU User Manual

APPENDICES
Number Name
OFF : Power supply on
CPU module startup
SM1517
status ON : Operation system
Tracking execution OFF : Batch operation mode
mode ON : Carryover mode
SM1518
Standby system to
ON
control system
OFF
switching status flag
Previous Control
ON
SM1519 System Identification
OFF
Flag
SM1520
SM1521
SM1522
SM1523
SM1524
SM1525
SM1526
SM1527
SM1528
SM1529
SM1530
SM1531
SM1532
SM1533
Data tracking block OFF : Disable tracking
SM1534
specification trigger ON
SM1535
SM1536
SM1537
SM1538
SM1539
SM1540
SM1541
SM1542
SM1543
SM1544
SM1545
SM1546
SM1547
SM1548
TableApp.13 Special relay
Meaning
• Turns on when the CPU module is started up by the
operation system switch.
• Reset using the user program.
startup
• Turns on when the CPU module is started up by the
system switching (switching from the standby system
switch starup
to the control system). Remains OFF when the
standby system is switched to the control system by
a power-ON startup.
• When this relay is turned OFF, the start of tracking is
delayed until it is executable if the tracking memory
is being used at END.
• When this relay is turned ON, the start of tracking is
carried over to next END if the tracking memory is
being used at END.
• Turns ON once switch between standby system to
control system, (ON for 1 scan only) occurs.
1 scan
• his status flag can only be used for scan execution
type programs
• On the last operation Control System was System
B,if power supply is supplied, or reset is released on
1 scan
both SYSTEM together,After RUN, ON for 1 scan
only by System A side.
SM1520 Block 1
SM1521 Block 2
SM1522 Block 3
SM1523 Block 4
SM1524 Block 5
SM1525 Block 6
SM1526 Block 7
SM1527 Block 8
SM1528 Block 9
SM1529 Block 10
SM1530 Block 11
SM1531 Block 12
SM1532 Block 13
SM1533 Block 14
SM1534 Block 15
: Enable tracking
SM1535 Block 16
SM1536 Block 17
SM1537 Block 18
SM1538 Block 19
SM1539 Block 20
SM1540 Block 21
SM1541 Block 22
SM1542 Block 23
SM1543 Block 24
SM1544 Block 25
SM1545 Block 26
SM1520 Block 27
SM1521 Block 28
SM1522 Block 29
Set by
Explanation
(When Set)
S (Status
change)/U
S (Status change)
S (Each END)
S (Each END)
<In the case of Q4AR>
• When data is transferred
by the data tracking
instruction S. TRUCK, the
target block is specified
as trigger.
<In the case of QnPRH>
• When data is transferred
<In the case of
based on the tracking
Q4AR>
setting of the redundant
parameter dialog box, the
target block is specified
<In the case of
as trigger.
QnPRH>
S (initial)/U
• When "Auto Tracking
block No.1" is enabled in
the tracking setting,
SM1520 is turned ON by
the system at power ON/
STOP to RUN. In other
cases, SM1520 to
SM1583 are turned ON
by the user.
Appendix 1 Special Relay List
Corres-
ponding
Corresponding CPU
ACPU
M9
New Q4AR
New QnPRH
U New Q4AR
New
QnPRH
New
U
Q4AR
New
QnPRH
App
9
10
11
- 22