Konica Minolta bizhub PRO C5500 Solution Manual page 53

bizhub PRO C5500
Procedure for Machine Log Capture :Insert USB drive into the service port on engine=> Press Utility => Utility => PowerSave =>
PowerSave.Interrupt & Accessibility buttons willflash until file is captured.
SPECIAL NOTE : Solution contribution by Mike McCarthy, Production Print/SSD
TAUS0642584EN*
Solution ID
Description
How to install an indicator light system (Status indicator light).
Solution
Konica Minolta does not supply an indicator light system. However, one can be purchased and installed. The following information is needed:
Patlite Corporation www.patlite.com/
Patlite LES-402A-RYGB (four light pole mounted system)
Patlite SZ-012 Mounting Bracket (needed to mount the light pole to the machine)
The following connectors are needed to connect the Light Pole Wiring to the machine:
Tyco Electronics AMP www.tycoelectronics.com/
Connector (concave) - 179228-6 (CRIMP TYPE II RECPT HSG)
Connector (convex) - 292254-6 (CT RELAY HDR ASSY 6P NAT)
Pins (6 needed) - 179518-1
Connector packed in installation kit has 7 wires. Only six are usedfor the light bar. Pin 1 is marked in the plastic of the connector with the black wires
attached;please look closely.
The wires on the machine plug side of the connector are numbered in reverse (pin 1 on the indicator light side of the connector is attached to pin 6 of the
machine side). Keep this in mind when consulting themachine schematics and the Service Manual sectionfor connecting the indicator light.
Connector pins below refer to the harness with the black wires that comes in the kit with the light.
Pin 1 is not used (would be a ground but our system switches to ground)
Pin 2 connected to the BLACK wire in the light harness(+24 volt power lead)
Pin 3 is connected to the ORANGE wire in the light harness and causes the AMBER light to come on. This happens when the machine is out of toner.
Pin 4 is connected to the RED wire in the light harness and causes the RED light to come on. This happens when there is a machine paper jam or when
there is a paper mismatch from the Fiery® controller and the Detail Check button comes on requiring customer interaction.
Pin 5 is connected to the GREEN wire in the light harness and causes the GREEN light to come on. This happens when the machine is operating normally
(making copies). The BLUE light is also on at this time.
Pin 6 is connected to the BLUE wire in the light harness and causes the BLUE light to come on. This happens when the machine is on and ready to copy,
print or scan but not actually running. The BLUE light is also on with the GREEN light when the machine is operating and making copies.
Note : This is a four-light system that indicates Ready, Operating, Low toner, and Jam.The wiring for the light system can be found in the Service
Manual.Please see attachments for reference. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the
Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Ed Bellone/Cesar Jimenez/Jim Behrends, Production Print/SSD and Clinton Marquardt, ESS
TAUS0651550EN*
Solution ID
Description
Konica Minolta Security White Paper.
Solution
See Security White Paper for details.
Notes :
a.To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
b. More in-depth security information is also availableon the Konica Minolta bizhub security page,
http://kmbs.konicaminolta.us/content/about/bizhubsecurity.html .
SPECIAL NOTE : Solution contribution by Jim Behrends and Mark D'Attilio, Production Print/SSD
Copyright , Konica Minolta Business Solutions U.S.A., Inc.
53
Miscellaneous
3
Solution Usage
3
Solution Usage
March 2010