Konica Minolta bizhub PRO C5500 Solution Manual page 106

bizhub PRO C5500
Check for damaged Tray 1 connectors. In this case, replace male connector - cassette signal wire(p/n 65AA 9017 0E).
SPECIAL NOTE : Solution contribution by Greg Lantowski/Jim Behrends/Mike McCarthy/Ian Lynch , Production Print/SSD
Solution ID TAUS0802207EN*
Description
"Press Start to Restart" message while operating. Machine will stop and message will appear withno jam or faultindicated.
Solution
CAUSE: A hesitation (slippage) has occurred in the paper feed section causing a timing abnormality. This hesitation is not large enough to cause a jam code
but machine will detect the abnormality and halt operation. This issue is most prevelant when running gloss stocks and/or during long runs.
SOLUTION: When issue occurs clean/replace feed components of paper tray currently in use. In the case of thick or glossy stocks adjust the feed roller
tension if issue is occuring frequently.
SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD
TAUS0802498EN*
Solution ID
Description
FS-607, J-7301 error code.
Solution
CAUSE: Either PS5 (p/n 08AA 8551 2) or its actuator (p/n 13QE 4807 0) have failed in the stacker unit.
SOLUTION: Replace PS5 and its actuator as a set.
Note : The operation of the stacker entrance sensor PS5 can be checked in I/O Check Mode using code 72-17.
SPECIAL NOTE : Solution contribution by Gary Scimeca and Ian Lynch, Production Print/SSD
Solution ID TAUS0802669EN*
Description
Finisher option capable of printing 13x19 jobs to the stapler main tray. The selection is "grayed out" in the printer driver properties for the FS-520/FS-607.
Solution
This is a normal operation with the FS-520 and FS-607 finishers for both print and copy operations. The physical specifications for the FS-520/FS-607
finishers do not support the output of 13x19 paper to the main tray. The paper can only be exited to the sub tray.
Output of 13x19 paper to the main tray is only available with the FS-503or FS-521 stapler finisher.Please refer to the attacheddocument for a listing of the
FS-503/FS-521/FS-520/FS-607 specifications.To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the
Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Tony Pizzoferrato, ESS and Ed Bellone/Mike McCarthy, Production Print/SSD
TAUS0808301EN*
Solution ID
Description
PF-601/PF-602, J-1610 jam code.
Solution
PROBABLE CAUSES:
1.The PFU DFeed Detect Adjustment was not performed after replacing the Multi-Feed Detection Board (MFDTB).
Perform the PFU DFeed Detect Adjustment. Please refer to attached pages from the Field Service Manual.
2. The PF Drive Board (PFDB) was just replaced and the multi-feed detection sensors are out of adjustment.
Perform the PFU DFeed Detect Adjustment. Please refer to attached pages from the Field Service Manual.
3. Failed Multi-feed Detection Board(Multi-feed Sensor Assembly).
Replace the sensor board assembly (p/n 15AG -840 1E).
Notes :
a.You can check the operation of the sensor in the I/O mode, Output Check18-04 (pressing the START button).
b. After repacing the MFDTB,perform the PFU DFeed Detect Adjustment. Please refer to attached pages from the Field Service Manual. To viewthe PDF,
Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
Copyright , Konica Minolta Business Solutions U.S.A., Inc.
Paper Conveyance jams, no-feed, folding, tearing, skewing, curling
106
Solution Usage 3
2
Solution Usage
Solution Usage 2
2
Solution Usage
March 2010