B Channel Defaults - Toshiba Strata CTX Programming Manual

Telephone Button Programming
300 Series Programs

B Channel Defaults

B Channel Position
Span Interface Speed
1.5M (T1)
2.0M (E1)
Programs 321~324
Button Sequence
321 Calling Number
Identification
,
"! C‚yq
321-00 OLG Number
n,
C‚yq
321-01 Default Number
, n,
A7 C‚yq
321-02 Number Prefix
, n,
A7! C‚yq
321-03 Number Verification
, n,
A7" C‚yq
321-04 Default Number 2
, n, ,
A7# C‚yq
322 CNIS Presentation
And Special Number
Assignment
,
"!! C‚yq
322-00 OLG Number
n,
C‚yq
322-01 Source Type
, n,
A7 C‚yq
322-02 Source Number
, n,
A7! C‚yq
322-03 Special Number
Assignments
, n, ,
A7" C‚yq
13-68
01~15
ON
ON
Value(s)
n = 1~32 (CTX100)
1~50 (CTX670 Basic)
1~128 (CTX670 Exp.)
n = Up to 10 digits
n = Up to 10 digits
n = 1. Enable
2. Disable
n = Up to 10 digits
C‚yq
n = 1~32 (CTX100)
1~50 (CTX670 Basic)
1~128 (CTX670 Exp.)
n = 1. Primary DN (0~99999)
2. Group CO (1~128)
3. Pooled Line Group
(1~128)
n = Up to 5 digits
GCO and POOL:
1~32 (CTX100)
1~50 (CTX670 Basic)
1~128 (CTX670 Exp.)
n = Up to 7 digits
C‚yq
16 17~23
ON ON
OFF (Dch Pos) ON
The Calling Number ID is what is defined as the user supplied Calling
Number. This number may be optionally screened by the PSTN to
ensure only calls from valid billable telephone numbers are allowed to
originate calls.
Enter the OLG Number.
Enter the telephone number to use by default when originating a call.
This is the number that the PSTN has registered for billing purposes.
Enter the prefix telephone number for which a DID number will be
appended to create a User Identified telephone number. This number
may or may not be a billed number, but is used for Caller ID at the
distant end and could be used for returning your call.
Specify whether the number provided should be screened by the
PSTN before the call is to proceed.
Enter the second telephone number to use by default when
originating a call. This is the number that the PSTN has registered for
billing purposes. The second number is for BRI only
When calls are sent to the PSTN with Calling Number Identification
Service (CNIS), the CTX can supply special CNIS information as part
of the Setup Message. This program may be used for sending a
unique number based on the source directing the call to the Strata
CTX PRI.
OLG Number.
Specify the type of circuit used for outgoing calls: 1- PDN; 2- GCO; 3-
Pooled Line.
Specify the number of the source type selected (PDN, GCO or Pooled
Line).
Note Entries for this field depend on the Destination Type chosen.
There are no default values for this field (default = no value).
•
PDN: 0~99999
•
GCO: 1~128
•
POOL: 1~128
Specify the number to be sent when calling out from the source (max.
seven digits). This number is appended to Program 321 FB02.
Note Destination Type and Destination must be entered before a
DID number can be assigned.
Strata CTX Programming - Part 3:Telephone Button Programming 04/03
24 25~31
OFF (Dch Pos)
ON ON
Summary