Telephone Button Programming
300 Series Programs
Programs 318~320
Button
Sequence
318-
Audio Day1/Day2/
05~07
Night Dst Type
~
, n,
A7$
A7&
Audio Day1/Day2/
Night Dst DN
n1,
Cyq
318-
Data Day1/Day2/
08~10
Night Dst Type
~
, n,
A7'
A7
Data Day1/Day2/
Night Dst DN
n1,
Cyq
318-11
VMID for DNIS No.
, n,
7
Cyq
318-12
DNIS Name
, n,
,
A7 !
Cyq
13-66
(continued)
Value(s)
n =
1. No Data (default)
2. Dialing Digits
3. DISA
Tx
4. Built-in modem
5. Night Bell
n1 =
Up to 32 digits
n =
1. No Data (default)
2. Dialing Digits
3. DISA
Tx
4. Built-in modem
5. Night Bell
n1 =
Up to 32 digits
n =
Up to 10 digits
n =
Up to 16 digits
Cyq
Select the Audio/Speech call Day1 destination type.
•
No Data – no destination will ring when the line rings into the
system.
•
Dialing Digits – assigns the line to ring the directory number or
access code defined in the "Destination Digits" assignment
•
DISA – assigns the line to ring in as a DISA call. DISA dial tone
will be returned to the caller.
•
Modem – assigns the line to ring the remote maintenance modem
on the CTX processor. Used to call into the system with a CTX
WinAdmin PC and modem.
•
Night Bell – Assigns the line to cause the night relay to pulse
(one-sec.close/3-sec.open)
Enter the Destination Directory Number. Destination DN is only
required if the destination type is "Dialing Digits"
Select the data call Day1 destination type
•
No Data (default), Dialing Digits, DISA, Built-in Modem or Night
Bell
•
No Data – no destination will ring when the line rings into the
system.
•
Dialing Digits – assigns the line to ring the directory number or
access code defined in the "Destination Digits" assignment
•
DISA – assigns the line to ring in as a DISA call. DISA dial tone
will be returned to the caller.
•
Modem – assigns the line to ring the remote maintenance modem
on the CTX processor. Used to call into the system with a CTX
WinAdmin PC and modem.
•
Night Bell – Assigns the line to cause the night relay to pulse
(one-sec.close/3-sec.open)
Enter the Destination Directory Number. Destination DN is only
required if the destination type is "Dialing Digits"
Enter the VM mail box number which should answer calls for this DID/
DNIS number.
This code is only sent if using SMDI VM integration in Program 580,
01. This code will be replaced, after voice mail answers, by the DTMF
code set in Program 318, 15 DID/DNIS DTMF VMID code - if
programmed; therefore, if using Program 318, 15 code, this VMID
code is not necessary.
This mail box number will be sent to voice mail on a DID/DNIS call
that rings directly to voice mail; and, on a direct DID/DNIS call to a DN
that forwards to voice mail before it is answered by the DN.
If a DID/DNIS call is answered by a station and then transferred to a
DN that forwards to voice mail, this mail box number of the DID/DNIS
number, or the forwarding DN's mail box number will be sent to voice
mail per Program 579, 01.
If this VMID code is not set, direct DID/DNIS calls will go to the VM
general greeting and DID/DNIS calls that forward from a DN to VM
will go to the DN's VMID mail box.
This Voice Mail box number is added to SMDI packets of direct and
forwarded DID\DNIS calls to voice mail as explained above.
Enter DNIS Name. DNIS names can be assigned from the CTX
WinAdmin (not from programming phones).
Strata CTX Programming - Part 3:Telephone Button Programming 04/03
Summary