Toshiba Strata CTX Programming Manual page 338

Telephone Button Programming
300 Series Programs
Programs 303~315
Button Sequence
309-15 VM Dial
, n, ,
A7 $ C‚yq ÃC‚yq
310 DIT Assignment
,
"  C‚yq
310-00 Line Equipment No.
xxyyzz,
C‚yq
310- Day1/Day2/Night
01~03 Destination Type
~ , n,
A7 A7"
Day1/Day2/Night
Destination Digits
n1,
C‚yq
13-60
(continued)
Value(s)
n = Digits 0~9, * and #. For a
pause enter Px, where
x=0~9 (seconds), up to 10
characters (default = no
value).
xx = Cabinet 1 (CTX100),
01~02 (CTX670 Basic),
01~07 (CTX670 Exp.)
yy = Slot 01~8 (CTX100),
01~10 (CTX670)
zz = Circuit 01~24
n = 1. No Data (default)
2. Dialing Digits
3. DISA
Tƒx…
4. Built-in Modem
5. Night Bell
n1 = Up to 32 digits
Enter the VM mail box number which should answer calls for this DID/
DNIS number.
This mail box number will be sent to voice mail on a DID/DNIS call
that rings directly to voice mail; and, on a direct DID/DNIS call to a DN
that forwards to voice mail before it is answered by the DN.
If a DID/DNIS call is answered by a station and then transferred to a
DN that forwards to voice mail, this mail box number of the DID/DNIS
number or the forwarding DN's mail box number will be sent to voice
mail per Program 579, 01.
If this VMID code is not set, direct DID/DNIS calls will go to the VM
general greeting and DID/DNIS calls that forward from a DN to VM
will go to the DN's VMID mail box. This voice mail box number is sent
to the VM port, as DTMF digits, after the VM port answers a DID/
DNIS call as explained above. These digits are sent to the VM port if
the CTX is set for SMDI or DTMF integration in Program 580, 01.
This command assigns DIT Number Analysis Table for DIT trunks.
DIT trunks are ground and loop start trunks.
Enter the trunk equipment number. Equipment numbers are required
when assigning a new trunk to the system. It can also be used to
display the equipment location of existing trunks.
Example: If a line should be assigned to an RCOU in cabinet shelf 5,
slot 2, circuit 3, enter 050203.
Cabinet numbers:
• CTX100 – Select 01 for Base and Expansion cabinet.
• CTX670 – Select 01 for Base and 02~07 respectively for each
Expansion cabinet.
Slot numbers:
•
CTX100 – Select 01~04 for Base slots and 05~08 for Expansion
slots.
•
CTX670 – Select 01~08 for Base slots and 01~10 for Expansion
slots.
Select Destination Type for each.
•
No Data – no destination will ring when the line rings into the
system.
•
Dialing Digits – assigns the line to ring the directory number or
access code defined in the "Destination Digits" assignment
• DISA – assigns the line to ring in as a DISA call. DISA dial tone
will be returned to the caller.
•
Modem – assigns the line to ring the remote maintenance modem
on the CTX processor. Used to call into the system with a CTX
WinAdmin PC and modem.
•
Night Bell – Assigns the line to cause the night relay to pulse
(one-sec. close/3-sec. open)
Enter Destination, Directory Number or Access Codes for each, only
if Dialing Digits is selected as Destination Type.
•
If Dialing Digits is the Destination Type, enter the Directory
Number that the line should ring.If the line should ring over
external page, enter #31xx, where xx is the external Page group
number.
•
If the default page access code #31 was changed, use the new
page access code as the leading digits.
•
Line access codes and network routing numbers can also be
entered to route incoming calls back out to a public or private
network number.
Strata CTX Programming - Part 3:Telephone Button Programming 04/03
Summary