Toshiba Strata CTX Programming Manual page 342

Telephone Button Programming
300 Series Programs
Programs 316~317
Button Sequence
317-07 Bearer Svc - 3.1 KHz
Audio
, n,
A7& C‚yq
317-08 Bearer Svc - 7 KHz
Audio
, n,
A7' C‚yq
317-09 Bearer Svc -
Unrestricted 64K
, n,
A7( C‚yq
317-10 Bearer Svc -
Unrestricted 56K
, n,
A7  C‚yq
317-11 Bearer Svc -
Unrestricted 2x64K
, n,
A7 C‚yq
317-12 Outgoing B Ch Select
, n,
A7 ! C‚yq
317-13 B Ch Selection
, n,
A7 " C‚yq
317-14 Initialize Type
, n,
A7 # C‚yq
317-15 Initialization Display
, n,
A7 $ C‚yq
317-16 SPID #1
, n,
A7 % C‚yq
317-17 SPID #2
, n,
A7 & C‚yq
317-18 T-Wait Timer
, n,
A7 ' C‚yq
317-19 Voice Calls
, n,
A7 ( C‚yq
317-20 Trunk Subscriber 1
, n,
A7! C‚yq
317-21 Trunk Subscriber 2
, n, ,
A7! C‚yq
13-64
(continued)
Value(s)
n = 1. Enable (default)
2. Disable
n = 1. Enable
2. Disable (default)
n = 1. Enable (default)
2. Disable
n = 1. Enable
2. Disable (default)
n = 1. Enable
2. Disable (default)
n = 1. Explicit
2. Preferred (default)
3. Any Channel
n = 1. Forward Cyclic
2. Backward Cyclic
(default)
3. Forward Terminal
4. Backward Terminal
n = 1. User Entry Of SPID
Auto SPID ON
2. User Entry Of SPID
Auto SPID OFF
3. Auto SPID
4. None (default)
n = Up to 4 digits
(default = User)
n = Up to 20 digits
n = Up to 20 digits
n = 1. Enable
2. Disable (default)
n = 1. One
2. Two (default)
n = Up to 10 digits
n = Up to 10 digits
C‚yq
Enable 3.1 KHz audio capability.
Enable 7 KHz audio capability.
Enable one of the unrestricted capabilities.
Select originating B Channel method.
•
Explicit – Channel is indicated, and no alternative is acceptable.
•
Preferred – (default) Channel is indicated, and any alternative is
acceptable.
•
Any Channel – Channel is indicated, and any channel is
acceptable.
Choose Idle B Channel selection method.
• Select Forward Cyclic (from lowest number to highest number of
B-channel).
•
Select Backward Cyclic (from highest number to lowest number
of B-channel).
•
Select Forward Terminal for the lowest numbered B-channel.
Select Backward Terminal for the oldest number B-channel. (The
High-High B-channel selection)
Enter the Service Profile Identifier (SPID) type of initialization.
Enter the text to be displayed for SPID Initialization.
Enter the SPID value. These fields are required if you selected
National ISDN in Protocol. When no data is entered, any previously
entered information is overwritten.
Enable the T-Wait Timer. This field is needed if you selected National
ISDN in Protocol above. This timer, used along with the SPID, assigns
random initializing SPID times to prevent BRI interfaces from re-
initialize at the same time after a reset or power outage.
Select the number of simultaneous voice (speech) calls that can exist
at the same time on this interface.
Enter the telephone number for subscriber 1. Telephone number
should be consistent with D channel data. If no data is entered in this
field any previously programmed information is lost.
Enter the telephone number for subscriber number 2. If no data is
entered in this field any previously programmed information is lost.
Strata CTX Programming - Part 3:Telephone Button Programming 04/03
Summary