KORG M50-88 Parameter Manual: Realtime Controls

M50 music workstation.
Hide thumbs
   
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419
Program mode
3. While holding down RESET CONTROLS, press the
current CONTROL ASSIGN switch again.
All of the knobs shown on the Control Surface will be reset
to the values stored in the Program.
Resetting Arpeggiator parameters
You can also perform the following reset operations for
Arpeggiator.
• To reset the knobs or switches of each arpeggiator, hold
down the RESET CONTROLS switch and press the ARP
switch.
0–8a: Program Select & Tempo
Bank (Bank Select)
Program Select [A...E: 000...127, GM, g(1)...g(9),
(Tempo)
This area displays information about the program selected
for editing: the program bank/number/ name, and the
tempo settings for the arpeggiator,
information, please see "0–1a: Program Select" on page 2.
0–8b: Control Assign
Control Assign [Realtime Control, External, ARP]
This selects the items that will be affected by the control
surface. You can also press one of the CONTROL ASSIGN
switches to make this selection.
For details on each selection, please see the explanations that
follow.
12
[A...E, GM, g(1)...g(9), g(d)]
g(d): 001...128]
[040.00...300.00, EXT]
etc.
For more

Realtime Controls

0–8a
0–8b
0–8c
Realtime Control lets you use the four knobs to edit the
parameters of a program or effect.
There are two modes of realtime control: A and B. Press the
REALTIME CONTROL switch to toggle between these two
modes. In each mode, you can use knobs 1–4 to control
parameters. Your selection of mode is remembered
independently for Program mode, Combination mode, and
Sequencer mode. If you switch to a different control surface
function, and then press the REALTIME CONTROL switch
to return to realtime control; the mode you had selected will
still be active.
In A mode, the functions assigned to knobs 1–4 are fixed. In
B mode, you can assign a variety of modulation functions to
knobs 1–4. To assign functions, use the P1: Basic/Ctrls–
Controllers Setup page (page 15).
0–8b: Control Assign, RTC Knob Mode,
Selected Parameter Information
Control Assign [Realtime Control, External, ARP]
This selects the items that will be controlled by the control
surface.
RTC Knob Mode
Selects either A or B as the realtime control mode for the
knobs. You can also use the front panel REALTIME
CONTROL switch to make this selection.
Selected Parameter information
When you select a knob, this area shows detailed
information about its parameter assignments.
0–8c: Realtime Control
RealTime Control A knob 1–4 (Knob1A–Knob4A) all have
dedicated functions which correspond to MIDI CCs.
RealTime Control B knob 1–4 (Knob1B–Knob4B) can be
assigned to a wide variety of functions, many of which also
have corresponding MIDI CCs.
When you move a knob, it sends out the corresponding
MIDI CC.
Unless otherwise noted, "scaling" means that the
parameters are at their programmed values when the
controller is at 64, at their minimum when the controller is at
0, and at their maximum when the controller is at 127. For
another look at this, please see the diagram below.
0–8
Menu
[A, B]

Advertising

   Related Manuals for KORG M50-88

This manual also for:

M50-73, M50-61

Comments to this Manuals

Symbols: 0
Latest comments: