Download Print this page

KORG M50-88 Parameter Manual: Global: Menu Command

M50 music workstation.
Hide thumbs
   
1
2
Table of Contents
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419

Advertisement

Global: Menu Command

Tip: In each page, you can access (or switch on/off) up to the
first ten menu commands by holding down the ENTER
switch and pressing the corresponding numeric key, 0–9.
Tip: While this command is open, the ENTER switch will
operate as the OK button and the EXIT switch will operate
as the Cancel button.
Procedure for menu commands
1. Select the menu command.
2. Make settings in the dialog box.
For details on the content of each dialog box, refer to the
following explanations of each command.
3. To execute, press the OK button. To cancel without exe-
cuting, press the Cancel button.
Write Global Setting
This command writes Global mode settings (except for
Drum Kits and Arpeggio Patterns).
You can also use the SEQUENCER REC/WRITE switch to
write data in the same way as the Write Global Setting
command.
Press the SEQUENCER REC/WRITE switch to access the
Update Global Setting dialog box, and press the OK button
to write the data.
Note: To save the drum kit, execute the P5 menu command.
("Write Drum Kits")
Note: To save the arpeggio pattern, execute the P6 menu
command. ("Write Arpeggio Patterns")
The Effect Global SW setting will not be saved.
Load Preload/Demo Data
This command loads the preloaded data and demo song
data into the M50.
Before you can load this data, you must navigate to
Memory Protect (Global 0–1b) and un-check the protect
setting for the type of data you want to load. If you
execute this operation with the protect setting checked,
the display will indicate "Memory Protected," and the
data will not be loaded.
1. Use Kind to select the type of data you want to load.
Global: Menu Command Write Global Setting
Kind
All PCG (Program, Combination, Global
All (Preload PCG and
settings, drum kit, , arpeggio pattern), and
Demo Songs)
demo song data
All Preload PCG
All PCG data
All Demo Songs
All demo song data
Program
Program data
Combination
Combination data
Drum Kit
Drum kit data
Arpeggio Pattern
Arpeggio pattern data
Global Setting
Global setting data
2. If you selected Program, Combination, Drum Kit, or
Arpeggio Pattern as the Kind, specify the range of data
that you want to load.
All: load all data
Bank: load an individual bank
Single: load one item of data
3. If you're loading Bank or Single, use To to specify the
loading-destination.
Change all bank references
This command changes all program banks specified for
timbres in combinations or tracks of songs.
1. If you wish to change bank references for combina-
tions, check Combination.
If you wish to change bank references for songs, check Song.
2. In Program Bank, specify the replacement for each
bank.
If you change two or more different banks to the same
bank, it will not be possible to use this function to
change them back to different banks. Be careful that the
change destination banks do not overlap.
Content
251

Advertisement

   Related Manuals for KORG M50-88

This manual also for:

M50-73, M50-61

Comments to this Manuals

Symbols: 0
Latest comments: