Effect Guide
090: Limiter - Cho/Flng
(Limiter - Chorus/Flanger)
This effect combines a mono limiter and a chorus/flanger.
You can change the order of the effects.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Limiter
+
Limiter
EQ Trim
Gain Adjust
Right
Envelope - Control
LIMITER
1.0 : 1...
[L]Ratio
50.0 : 1, Inf : 1
a
Threshold
–40...0
[dB]
[L]Attack
1...100
b
Release
1...100
[L]Gain
–Inf,
c
Adjust [dB]
–38...+24
CHORUS/FLANGER
[F]LFO
Frequency
0.02...20.00
[Hz]
d
LFO
Triangle,
Waveform
Sine
[F]Delay
Time [msec] 0.0...1350.0
e
Depth
0...100
Feedback
–100...+100
f
[F]EQ Trim
0...100
[F]Pre LEQ
–15...+15
Gain [dB]
g
Pre HEQ Gain
–15...+15
[dB]
–Wet...
[F]Cho/Flng
–1 : 99, Dry,
Wet/Dry
1 : 99...Wet
h
Src
Off...Tempo
Amt
–100...+100
[F]Output
Normal,
Mode
Wet Invert
Limiter ➝
i
Flanger,
Routing
Flanger ➝
Limiter
Dry, 1 : 99...
Wet/Dry
99 : 1, Wet
j
Src
Off...Tempo
Amt
–100...+100
344
Routing
Chorus/Flanger
Chorus/Flanger
Normal
LEQ HEQ
+
Output Mode
–
Wet Invert
Feedback
Cho/Flng Wet / Dry
LFO: Tri / Sine
Sets the signal compression
ratio
p.343
Sets the level above which the
compressor is applied
p.343
Sets the attack time
Sets the release time
Sets the limiter output gain
p.343
Sets the speed of the LFO
Selects the LFO Waveform
Sets the delay time
Sets the depth of LFO
modulation
Sets the feedback amount
p.310
Sets the EQ input level
Sets the gain of Low EQ
Sets the gain of High EQ
Sets the effect balance of the
chorus/flanger
p.299, p.310
Selects the Wet/Dry
modulation source for the
chorus/flanger
Sets the Wet/Dry modulation
amount for the chorus/flanger
Selects the output mode for the
chorus/flanger
p.341
Switches the order of the
limiter and chorus/flanger
Sets the balance between the
effect and the dry input
Selects a modulation source for
Wet/Dry
Sets the modulation amount
for Wet/Dry
091: Limiter - Phaser
This effect combines a mono limiter and a phaser. You can
change the order of the effects.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Wet / Dry
+
Right
Envelope - Control
Wet / Dry
LIMITER
[L]Ratio
a
Threshold
[dB]
[L]Attack
b
Release
[L]Gain
c
Adjust [dB]
PHASER
[P]LFO
Frequency
[Hz]
d
LFO
Waveform
[P]Manual
e
Depth
Resonance
[P]Phaser
Wet/Dry
f
Src
Amt
[P]Output
g
Mode
h Routing
Wet/Dry
i
Src
Amt
Routing
Limiter
Phaser
Limiter
Phaser
Gain Adjust
+
–
Resonance
Phaser Wet / Dry
LFO: Tri / Sine
1.0 : 1...
Sets the signal compression
50.0 : 1, Inf : 1
ratio
Sets the level above which the
–40...0
compressor is applied
1...100
Sets the attack time
1...100
Sets the release time
–Inf,
Sets the limiter output gain
–38...+24
0.02...20.00
Sets the speed of the LFO
Triangle,
Selects the LFO Waveform
Sine
Sets the frequency to which the
0...100
effect is applied
Sets the depth of LFO
0...100
modulation
Sets the resonance amount
–100...+100
–Wet...
Sets the phaser effect balance
–1 : 99, Dry,
p.299, p.312
1 : 99...Wet
Selects the phaser's Wet/Dry
Off...Tempo
modulation source
Sets the phaser's Wet/Dry
–100...+100
modulation amount
Normal,
Selects the phaser output
Wet Invert
mode
Limiter ➝
Phaser,
Switches the order of the
Phaser ➝
limiter and phaser
Limiter
Dry, 1 : 99...
Sets the balance between the
99 : 1, Wet
effect and the dry input
Selects a modulation source for
Off...Tempo
Wet/Dry
Sets the modulation amount
–100...+100
for Wet/Dry
Wet / Dry
Normal
Output Mode
Wet Invert
Wet / Dry
p.343
p.343
p.343
p.312
p.338
p.341
Comments to this Manuals
Latest comments: