Korg M50-88 Parameter Manual page 225

M50 series music workstation
Table of Contents

Advertisement

Aftertouch Curve (MIDI IN)
This specifies the way in which incoming aftertouch data
will affect the volume or tone when Convert Position
(Global 1–1a) is set to PostMIDI.
This setting has no effect when Convert Position
(Global 1–1a) is set to PreMIDI.
This curve is applied immediately before the tone generator.
The aftertouch Curve setting selects the curve that is
applied to the incoming aftertouch.
After Touch (MIDI In→TG)
Aftertouch
effect
1, 2: This curve produces change when strong aftertouch
pressure is applied.
3 (Normal): The normal curve.
4, 5: This curve produces change even when light pressure is
applied.
6, 7: These curves produce change in 24 or 12 steps. Curve
number 7 allows change over twelve steps, so when using
aftertouch to modify the pitch, you can set the range of
modification to one octave, and use aftertouch to vary the
pitch in semitone steps.
8: This is a random curve. Use this when you wish to create
special effects, or to use aftertouch to apply unpredictable
modulation.
With a setting of aftertouch, the setting you make here
will be applied immediately before the M50's internal
tone generator, meaning that it will affect the data
received via MIDI, but will not affect the transmitted
data.
[1...8]
MAX
5
4
7
3
2
8:RANDOM
6
1
0
127
Global P0: Basic Setup 0–1: Basic
0–1b: Effect Global SW
IFX 1–5 Off
On (checked): All insert effects IFX1–5 will be off.
Off (unchecked): The P8: Insert Effect settings for each IFX
On/Off in Program, Combination, and Sequencer modes
will be valid.
MFX1&2 Off
On (checked): Master Effect1 and 2 (MFX1, 2) will be off.
Off (unchecked): The P9: MFX/TFX setting MFX1 On/Off,
and MFX2 On/Off, in Program, Combination, and
Sequencer modes will be valid.
TFX Off
On (checked): Total effect (TFX) will be off.
Off (unchecked): The P9: MFX/TFX setting TFX On/Off, in
Program, Combination, and Sequencer modes will be valid.
When IFX Off, MFX1&2 Off,, or TFX Off settings are
switched, control change messages CC#92 (effect
control 2), CC#94 (effect control 4), and CC#95 (effect
control 5) will be transmitted respectively. The
transmitted data will be 0 for off, and 127 for on.
0–1c: ARP/Drum Track
All ARP/DT Off
On (checked): All arpeggiator and Drum Track functions
will be off. The arpeggiator will not operate even if the ARP
ON/OFF switch is on. The Drum Track function will not
operate even if the DRUM TRACK ON/OFF switch is on.
Off (unchecked): The arpeggiator settings and ARP ON/
OFF switch settings in Program, Combination, and
Sequencer modes will be used. The Drum Track function
will operate according to the settings in each mode and the
state of the DRUM TRACK ON/OFF switch.
Load ARP when changing:
Program
On (checked): When you switch programs, the arpeggiator
settings stored in that program will be used. Normally you
will use the On setting.
Off (unchecked): The arpeggiator settings will not change
even if you switch programs. Use this setting if you want to
switch Program sounds without changing the phrases from
the arpeggiator.
Combination
On (checked): When you switch combinations, the
arpeggiator settings stored in that combination will be used.
Normally you will use the On setting.
Off (unchecked): The arpeggiator settings will not change
even if you switch combinations. Use this setting if you
want only to switch combination sounds without changing
the phrases from the arpeggiator.
[Off, On]
[Off, On]
[Off, On]
[Off, On]
[Off, On]
[Off, On]
217

Advertisement

Table of Contents
loading

This manual is also suitable for:

M50-73M50-61

Table of Contents